@@ -413,7 +413,7 @@ static struct fixed_voltage_config can_regulator_pdata = {
static struct platform_device can_regulator_device = {
.name = "reg-fixed-volage",
- .id = -1,
+ .id = 0,
.dev = {
.platform_data = &can_regulator_pdata,
},
@@ -510,18 +510,6 @@ struct platform_device zeus_max6369_device = {
.num_resources = 1,
};
-static struct platform_device *zeus_devices[] __initdata = {
- &zeus_serial_device,
- &zeus_mtd_devices[0],
- &zeus_dm9k0_device,
- &zeus_dm9k1_device,
- &zeus_sram_device,
- &zeus_leds_device,
- &zeus_pcmcia_device,
- &zeus_max6369_device,
- &can_regulator_device,
-};
-
/* AC'97 */
static pxa2xx_audio_ops_t zeus_ac97_info = {
.reset_gpio = 95,
@@ -532,44 +520,50 @@ static pxa2xx_audio_ops_t zeus_ac97_info = {
* USB host
*/
-static int zeus_ohci_init(struct device *dev)
-{
- int err;
-
- /* Switch on port 2. */
- if ((err = gpio_request(ZEUS_USB2_PWREN_GPIO, "USB2_PWREN"))) {
- dev_err(dev, "Can't request USB2_PWREN\n");
- return err;
- }
-
- if ((err = gpio_direction_output(ZEUS_USB2_PWREN_GPIO, 1))) {
- gpio_free(ZEUS_USB2_PWREN_GPIO);
- dev_err(dev, "Can't enable USB2_PWREN\n");
- return err;
- }
+static struct regulator_consumer_supply zeus_ohci_regulator_supplies[] = {
+ REGULATOR_SUPPLY("vbus2", "pxa27x-ohci"),
+};
- /* Port 2 is shared between host and client interface. */
- UP2OCR = UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+static struct regulator_init_data zeus_ohci_regulator_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(zeus_ohci_regulator_supplies),
+ .consumer_supplies = zeus_ohci_regulator_supplies,
+};
- return 0;
-}
+static struct fixed_voltage_config zeus_ohci_regulator_config = {
+ .supply_name = "vbus2",
+ .microvolts = 5000000, /* 5.0V */
+ .gpio = ZEUS_USB2_PWREN_GPIO,
+ .enable_high = 1,
+ .startup_delay = 0,
+ .init_data = &zeus_ohci_regulator_data,
+};
-static void zeus_ohci_exit(struct device *dev)
-{
- /* Power-off port 2 */
- gpio_direction_output(ZEUS_USB2_PWREN_GPIO, 0);
- gpio_free(ZEUS_USB2_PWREN_GPIO);
-}
+static struct platform_device zeus_ohci_regulator_device = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &zeus_ohci_regulator_config,
+ },
+};
static struct pxaohci_platform_data zeus_ohci_platform_data = {
.port_mode = PMM_NPS_MODE,
/* Clear Power Control Polarity Low and set Power Sense
* Polarity Low. Supply power to USB ports. */
.flags = ENABLE_PORT_ALL | POWER_SENSE_LOW,
- .init = zeus_ohci_init,
- .exit = zeus_ohci_exit,
};
+static void zeus_register_ohci(void)
+{
+ /* Port 2 is shared between host and client interface. */
+ UP2OCR = UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+
+ pxa_set_ohci_info(&zeus_ohci_platform_data);
+}
+
/*
* Flat Panel
*/
@@ -677,6 +671,19 @@ static struct pxa2xx_udc_mach_info zeus_udc_info = {
.udc_command = zeus_udc_command,
};
+static struct platform_device *zeus_devices[] __initdata = {
+ &zeus_serial_device,
+ &zeus_mtd_devices[0],
+ &zeus_dm9k0_device,
+ &zeus_dm9k1_device,
+ &zeus_sram_device,
+ &zeus_leds_device,
+ &zeus_pcmcia_device,
+ &zeus_max6369_device,
+ &can_regulator_device,
+ &zeus_ohci_regulator_device,
+};
+
#ifdef CONFIG_PM
static void zeus_power_off(void)
{
@@ -847,7 +854,7 @@ static void __init zeus_init(void)
platform_add_devices(zeus_devices, ARRAY_SIZE(zeus_devices));
- pxa_set_ohci_info(&zeus_ohci_platform_data);
+ zeus_register_ohci();
if (zeus_setup_fb_gpios())
pr_err("Failed to setup fb gpios\n");
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- arch/arm/mach-pxa/zeus.c | 89 ++++++++++++++++++++++++++---------------------- 1 file changed, 48 insertions(+), 41 deletions(-)