@@ -104,6 +104,13 @@ config MACH_KIRKWOOD
Say 'Y' here if you want your kernel to support boards based
on the Marvell Kirkwood device tree.
+config MACH_NETXBIG
+ bool "LaCie 2Big and 5Big Network v2"
+ depends on MACH_KIRKWOOD
+ help
+ Say 'Y' here if you want your kernel to support the
+ LaCie 2Big and 5Big Network v2
+
endmenu
endif
@@ -14,3 +14,4 @@ endif
obj-$(CONFIG_MACH_DOVE) += dove.o
obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o
+obj-$(CONFIG_MACH_NETXBIG) += board-netxbig.o
new file mode 100644
@@ -0,0 +1,191 @@
+/*
+ * arch/arm/mach-mvbu/board-netxbig.c
+ *
+ * LaCie 2Big and 5Big Network v2 board setup
+ *
+ * Copyright (C) 2010 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/leds-kirkwood-netxbig.h>
+#include "common.h"
+
+/*****************************************************************************
+ * GPIO extension LEDs
+ ****************************************************************************/
+
+/*
+ * The LEDs are controlled by a CPLD and can be configured through a GPIO
+ * extension bus:
+ *
+ * - address register : bit [0-2] -> GPIO [47-49]
+ * - data register : bit [0-2] -> GPIO [44-46]
+ * - enable register : GPIO 29
+ */
+
+static int netxbig_v2_gpio_ext_addr[] = { 47, 48, 49 };
+static int netxbig_v2_gpio_ext_data[] = { 44, 45, 46 };
+
+static struct netxbig_gpio_ext netxbig_v2_gpio_ext = {
+ .addr = netxbig_v2_gpio_ext_addr,
+ .num_addr = ARRAY_SIZE(netxbig_v2_gpio_ext_addr),
+ .data = netxbig_v2_gpio_ext_data,
+ .num_data = ARRAY_SIZE(netxbig_v2_gpio_ext_data),
+ .enable = 29,
+};
+
+/*
+ * Address register selection:
+ *
+ * addr | register
+ * ----------------------------
+ * 0 | front LED
+ * 1 | front LED brightness
+ * 2 | SATA LED brightness
+ * 3 | SATA0 LED
+ * 4 | SATA1 LED
+ * 5 | SATA2 LED
+ * 6 | SATA3 LED
+ * 7 | SATA4 LED
+ *
+ * Data register configuration:
+ *
+ * data | LED brightness
+ * -------------------------------------------------
+ * 0 | min (off)
+ * - | -
+ * 7 | max
+ *
+ * data | front LED mode
+ * -------------------------------------------------
+ * 0 | fix off
+ * 1 | fix blue on
+ * 2 | fix red on
+ * 3 | blink blue on=1 sec and blue off=1 sec
+ * 4 | blink red on=1 sec and red off=1 sec
+ * 5 | blink blue on=2.5 sec and red on=0.5 sec
+ * 6 | blink blue on=1 sec and red on=1 sec
+ * 7 | blink blue on=0.5 sec and blue off=2.5 sec
+ *
+ * data | SATA LED mode
+ * -------------------------------------------------
+ * 0 | fix off
+ * 1 | SATA activity blink
+ * 2 | fix red on
+ * 3 | blink blue on=1 sec and blue off=1 sec
+ * 4 | blink red on=1 sec and red off=1 sec
+ * 5 | blink blue on=2.5 sec and red on=0.5 sec
+ * 6 | blink blue on=1 sec and red on=1 sec
+ * 7 | fix blue on
+ */
+
+static int netxbig_v2_red_mled[NETXBIG_LED_MODE_NUM] = {
+ [NETXBIG_LED_OFF] = 0,
+ [NETXBIG_LED_ON] = 2,
+ [NETXBIG_LED_SATA] = NETXBIG_LED_INVALID_MODE,
+ [NETXBIG_LED_TIMER1] = 4,
+ [NETXBIG_LED_TIMER2] = NETXBIG_LED_INVALID_MODE,
+};
+
+static int netxbig_v2_blue_pwr_mled[NETXBIG_LED_MODE_NUM] = {
+ [NETXBIG_LED_OFF] = 0,
+ [NETXBIG_LED_ON] = 1,
+ [NETXBIG_LED_SATA] = NETXBIG_LED_INVALID_MODE,
+ [NETXBIG_LED_TIMER1] = 3,
+ [NETXBIG_LED_TIMER2] = 7,
+};
+
+static int netxbig_v2_blue_sata_mled[NETXBIG_LED_MODE_NUM] = {
+ [NETXBIG_LED_OFF] = 0,
+ [NETXBIG_LED_ON] = 7,
+ [NETXBIG_LED_SATA] = 1,
+ [NETXBIG_LED_TIMER1] = 3,
+ [NETXBIG_LED_TIMER2] = NETXBIG_LED_INVALID_MODE,
+};
+
+static struct netxbig_led_timer netxbig_v2_led_timer[] = {
+ [0] = {
+ .delay_on = 500,
+ .delay_off = 500,
+ .mode = NETXBIG_LED_TIMER1,
+ },
+ [1] = {
+ .delay_on = 500,
+ .delay_off = 1000,
+ .mode = NETXBIG_LED_TIMER2,
+ },
+};
+
+#define NETXBIG_LED(_name, maddr, mval, baddr) \
+ { .name = _name, \
+ .mode_addr = maddr, \
+ .mode_val = mval, \
+ .bright_addr = baddr }
+
+static struct netxbig_led net2big_v2_leds_ctrl[] = {
+ NETXBIG_LED("net2big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled, 1),
+ NETXBIG_LED("net2big-v2:red:power", 0, netxbig_v2_red_mled, 1),
+ NETXBIG_LED("net2big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net2big-v2:red:sata0", 3, netxbig_v2_red_mled, 2),
+ NETXBIG_LED("net2big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net2big-v2:red:sata1", 4, netxbig_v2_red_mled, 2),
+};
+
+static struct netxbig_led_platform_data net2big_v2_leds_data = {
+ .gpio_ext = &netxbig_v2_gpio_ext,
+ .timer = netxbig_v2_led_timer,
+ .num_timer = ARRAY_SIZE(netxbig_v2_led_timer),
+ .leds = net2big_v2_leds_ctrl,
+ .num_leds = ARRAY_SIZE(net2big_v2_leds_ctrl),
+};
+
+static struct netxbig_led net5big_v2_leds_ctrl[] = {
+ NETXBIG_LED("net5big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled, 1),
+ NETXBIG_LED("net5big-v2:red:power", 0, netxbig_v2_red_mled, 1),
+ NETXBIG_LED("net5big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net5big-v2:red:sata0", 3, netxbig_v2_red_mled, 2),
+ NETXBIG_LED("net5big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net5big-v2:red:sata1", 4, netxbig_v2_red_mled, 2),
+ NETXBIG_LED("net5big-v2:blue:sata2", 5, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net5big-v2:red:sata2", 5, netxbig_v2_red_mled, 2),
+ NETXBIG_LED("net5big-v2:blue:sata3", 6, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net5big-v2:red:sata3", 6, netxbig_v2_red_mled, 2),
+ NETXBIG_LED("net5big-v2:blue:sata4", 7, netxbig_v2_blue_sata_mled, 2),
+ NETXBIG_LED("net5big-v2:red:sata5", 7, netxbig_v2_red_mled, 2),
+};
+
+static struct netxbig_led_platform_data net5big_v2_leds_data = {
+ .gpio_ext = &netxbig_v2_gpio_ext,
+ .timer = netxbig_v2_led_timer,
+ .num_timer = ARRAY_SIZE(netxbig_v2_led_timer),
+ .leds = net5big_v2_leds_ctrl,
+ .num_leds = ARRAY_SIZE(net5big_v2_leds_ctrl),
+};
+
+static struct platform_device netxbig_v2_leds = {
+ .name = "leds-netxbig",
+ .id = -1,
+ .dev = {
+ .platform_data = &net2big_v2_leds_data,
+ },
+};
+
+void __init netxbig_init(void)
+{
+
+ if (of_machine_is_compatible("lacie,net5big"))
+ netxbig_v2_leds.dev.platform_data = &net5big_v2_leds_data;
+ platform_device_register(&netxbig_v2_leds);
+}
@@ -13,4 +13,9 @@
#ifndef __ARCH_MVEBU_BOARD_H
#define __ARCH_MVEBU_BOARD_H
+#ifdef CONFIG_MACH_NETXBIG
+void netxbig_init(void);
+#else
+static inline void netxbig_init(void) {};
+#endif
#endif
@@ -180,6 +180,9 @@ static void __init kirkwood_dt_init(void)
kirkwood_pm_init();
kirkwood_dt_eth_fixup();
+ if (of_machine_is_compatible("lacie,netxbig"))
+ netxbig_init();
+
of_platform_populate(NULL, of_default_bus_match_table, auxdata, NULL);
}
There is currently no DT binding for the CPLD which controls the LEDs on the Net 2Big and Net 5Big. So use a platform device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> --- arch/arm/mach-mvebu/Kconfig | 7 ++ arch/arm/mach-mvebu/Makefile | 1 + arch/arm/mach-mvebu/board-netxbig.c | 191 ++++++++++++++++++++++++++++++++++++ arch/arm/mach-mvebu/board.h | 5 + arch/arm/mach-mvebu/kirkwood.c | 3 + 5 files changed, 207 insertions(+) create mode 100644 arch/arm/mach-mvebu/board-netxbig.c