| Message ID | 1404541530-27856-3-git-send-email-peter.griffin@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Subject is wrong, this has nothing to do with ARM. Should be USB. On Sat, 05 Jul 2014, Peter Griffin wrote: > This patch documents the device tree documentation required for > the ST usb3 controller glue layer found in STiH407 devices. > > Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > --- > Documentation/devicetree/bindings/usb/dwc3-st.txt | 58 +++++++++++++++++++++++ > 1 file changed, 58 insertions(+) > create mode 100644 Documentation/devicetree/bindings/usb/dwc3-st.txt > > diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt > new file mode 100644 > index 0000000..befd964 > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt > @@ -0,0 +1,58 @@ > +ST DWC3 glue logic > + > +This file documents the parameters for the dwc3-st driver. Does this line really add anything to do the document, considering the name and location of the file and the title above? > +This driver provides the glue logic to use the dwc3 on STiH407 based platforms. s/This driver/The DWC2 driver/ > +Required properties: > + - compatible : must be "st,stih407-dwc3" > + - reg : glue logic base address and USB syscfg ctrl register offset > + - reg-names : should be "reg-glue" and "syscfg-reg" Any reason why you have reg-* and *-reg? If you have to put 'reg' in the name, it's usually appended, rather than prefixed. > + - st,syscon : should be phandle to system configuration node which > + encompasses the glue registers > + - resets : phandle pointing to the system powerdown controller > +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt > +See: Documentation/devicetree/bindings/reset/reset.txt > + > + - #address-cells, #size-cells : should be '1' if the device has sub-nodes > + with 'reg' property > + > + - pinctl-names : A pinctrl state named "default" must be defined > +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt > + > + - pinctrl-0 : Pin control group > +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt > + > + - ranges : allows valid 1:1 translation between child's address space and > + parent's address space > + > +Optional properties: > + - st,dwc3-drd-device: to program the HC as "device" (static setup) This will require a DT Ack. > +Sub-nodes: > +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the > +example below. The DT binding details of dwc3 can be found in: > +Documentation/devicetree/bindings/usb/dwc3.txt > + > +Example: > + > +st_dwc3: dwc3@8f94000 { > + status = "disabled"; Probably not good to disable the node in the example. > + compatible = "st,stih407-dwc3"; > + reg = <0x08f94000 0x1000>, <0x110 0x4>; > + reg-names = "reg-glue", "syscfg-reg"; > + st,syscfg = <&syscfg_core>; > + resets = <&powerdown STIH407_USB3_POWERDOWN>; > + #address-cells = <1>; > + #size-cells = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb3>; > + ranges; > + > + dwc3: dwc3@9900000 { > + compatible = "synopsys,dwc3"; > + reg = <0x09900000 0x100000>; > + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; > + > + usb-phy = <&usb2_phy>, <&usb3_phy>; > + }; > +};
diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt new file mode 100644 index 0000000..befd964 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -0,0 +1,58 @@ +ST DWC3 glue logic + +This file documents the parameters for the dwc3-st driver. +This driver provides the glue logic to use the dwc3 on STiH407 based platforms. + +Required properties: + - compatible : must be "st,stih407-dwc3" + - reg : glue logic base address and USB syscfg ctrl register offset + - reg-names : should be "reg-glue" and "syscfg-reg" + - st,syscon : should be phandle to system configuration node which + encompasses the glue registers + - resets : phandle pointing to the system powerdown controller +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property + + - pinctl-names : A pinctrl state named "default" must be defined +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - pinctrl-0 : Pin control group +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + +Optional properties: + - st,dwc3-drd-device: to program the HC as "device" (static setup) + +Sub-nodes: +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the +example below. The DT binding details of dwc3 can be found in: +Documentation/devicetree/bindings/usb/dwc3.txt + +Example: + +st_dwc3: dwc3@8f94000 { + status = "disabled"; + compatible = "st,stih407-dwc3"; + reg = <0x08f94000 0x1000>, <0x110 0x4>; + reg-names = "reg-glue", "syscfg-reg"; + st,syscfg = <&syscfg_core>; + resets = <&powerdown STIH407_USB3_POWERDOWN>; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; + ranges; + + dwc3: dwc3@9900000 { + compatible = "synopsys,dwc3"; + reg = <0x09900000 0x100000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + + usb-phy = <&usb2_phy>, <&usb3_phy>; + }; +};