diff mbox

[v2,2/3] usb: host: st-hcd: Add st-hcd devicetree bindings documentation.

Message ID 1406199616-10533-3-git-send-email-peter.griffin@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Peter Griffin July 24, 2014, 11 a.m. UTC 
This patch documents the device tree documentation required for
the ST HCD controller found in STMicroelectronics SoCs.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 Documentation/devicetree/bindings/usb/st-hcd.txt | 49 ++++++++++++++++++++++++
 1 file changed, 49 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/st-hcd.txt

Comments

Lee Jones July 24, 2014, 11:16 a.m. UTC | #1 
On Thu, 24 Jul 2014, Peter Griffin wrote:

> This patch documents the device tree documentation required for
> the ST HCD controller found in STMicroelectronics SoCs.
> 
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
>  Documentation/devicetree/bindings/usb/st-hcd.txt | 49 ++++++++++++++++++++++++
>  1 file changed, 49 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/st-hcd.txt

If you've fixed the nits from the previous review, you should have
applied my Ack for this submission.

Acked-by: Lee Jones <lee.jones@linaro.org>
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/usb/st-hcd.txt b/Documentation/devicetree/bindings/usb/st-hcd.txt
new file mode 100644
index 0000000..b963be2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/st-hcd.txt
@@ -0,0 +1,49 @@ 
+ST HCD (Host Controller Driver) for USB 2.0 and 1.1
+
+The device node has the following properties.
+
+Required properties:
+ - compatible		: must be "st,usb-300x"
+ - reg			: physical base addresses of the controller and length of memory mapped
+			  region
+ - reg-names		: names associated to the reg defines above, should be "ehci" and "ohci"
+ - interrupts		: interrupt numbers to the cpu
+ - interrupt-names	: should be "ehci" and "ohci"
+
+ - pinctrl-names	: a pinctrl state named "default" must be defined
+-  pinctrl-0		: phandle referencing pin configuration of the USB controller
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - clocks		: phandle list of usb clocks.
+ - clock-names		: should be "ic" for interconnect clock and "ohci" for the 48MHz clock
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+ - resets		: phandle to the powerdown and reset controller for the USB IP
+ - reset-names		: should be "powerdown" and "softreset".
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+usb0: usb@fe100000 {
+	compatible	= "st,usb-300x";
+	reg		= <0xfe1ffc00 0x100>,
+			  <0xfe1ffe00 0x100>;
+	reg-names	= "ohci", "ehci";
+
+	interrupts	=  <GIC_SPI 148 IRQ_TYPE_NONE>,
+			   <GIC_SPI 149 IRQ_TYPE_NONE>;
+	interrupt-names	= "ehci", "ohci";
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_usb0>;
+	clocks		= <&clk_s_a1_ls CLK_ICN_IF_2>,
+			  <&clockgen_b0 0>;
+	clock-names	= "ic", "ohci";
+
+	resets		= <&powerdown STIH416_USB0_POWERDOWN>,
+			  <&softreset STIH416_USB0_SOFTRESET>;
+	reset-names	= "powerdown", "softreset";
+
+	phys		= <&usb2_phy>;
+	phy-names	= "usb2-phy";
+};