[v11,19/19] serial: imx: Add support for KGDB's FIQ/NMI mode

Commit Message

Daniel Thompson Sept. 2, 2014, 1 p.m. UTC

This patch makes it possible to use the imx uart with KGDB's FIQ/NMI
mode.

Main changes are:

.poll_init() will, if KGDB+FIQ are enabled, perform deeper hardware
initialization to ensure the serial port is always active (required
otherwise FIQ is not triggered by UART activity). This has an impact on
power usage so it is conservatively enabled.

imx_put_poll_char() has been simplified to remove the code to disable
interrupts. The present code can corrupt register state when re-entered
from FIQ handler.

Both imx_put_poll_char() and imx_get_poll_char() adopt _relaxed()
MMIO functions (which are safe for polled I/O and needed to avoid taking
spin locks).

Signed-off-by: Daniel Thompson <[e-mail]>
Cc: Greg Kroah-Hartman <[e-mail]>
Cc: Jiri Slaby <[e-mail]>
Cc: [e-mail]
Acked-by: Dirk Behme <[e-mail]>
---
 drivers/tty/serial/imx.c | 71 +++++++++++++++++++++++++++++++++++-------------
 1 file changed, 52 insertions(+), 19 deletions(-)

Patch

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 983668a..a201c61 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -49,6 +49,7 @@ 
 #include <linux/of_device.h>
 #include <linux/io.h>
 #include <linux/dma-mapping.h>
+#include <linux/kgdb.h>
 
 #include <asm/irq.h>
 #include <linux/platform_data/serial-imx.h>
@@ -1505,44 +1506,73 @@  imx_verify_port(struct uart_port *port, struct serial_struct *ser)
 }
 
 #if defined(CONFIG_CONSOLE_POLL)
+
+#if defined(CONFIG_KGDB_FIQ)
+/*
+ * Prepare the UART to be used from kgdb's NMI support.
+ */
+static int imx_poll_init(struct uart_port *port)
+{
+	struct imx_port *sport = (struct imx_port *)port;
+	unsigned long flags;
+	unsigned long temp;
+	int retval;
+
+	retval = clk_prepare_enable(sport->clk_ipg);
+	if (retval)
+		return retval;
+	retval = clk_prepare_enable(sport->clk_per);
+	if (retval)
+		clk_disable_unprepare(sport->clk_ipg);
+
+	imx_setup_ufcr(sport, 0);
+
+	spin_lock_irqsave(&sport->port.lock, flags);
+
+	temp = readl(sport->port.membase + UCR1);
+	if (is_imx1_uart(sport))
+		temp |= IMX1_UCR1_UARTCLKEN;
+	temp |= UCR1_UARTEN | UCR1_RRDYEN;
+	temp &= ~(UCR1_TXMPTYEN | UCR1_RTSDEN);
+	writel(temp, sport->port.membase + UCR1);
+
+	temp = readl(sport->port.membase + UCR2);
+	temp |= UCR2_RXEN;
+	writel(temp, sport->port.membase + UCR2);
+
+	spin_unlock_irqrestore(&sport->port.lock, flags);
+
+	/* register the FIQ with kgdb */
+	kgdb_register_fiq(sport->port.irq);
+
+	return 0;
+}
+#endif /* CONFIG_KGDB_FIQ */
+
 static int imx_poll_get_char(struct uart_port *port)
 {
-	if (!(readl(port->membase + USR2) & USR2_RDR))
+	if (!(readl_relaxed(port->membase + USR2) & USR2_RDR))
 		return NO_POLL_CHAR;
 
-	return readl(port->membase + URXD0) & URXD_RX_DATA;
+	return readl_relaxed(port->membase + URXD0) & URXD_RX_DATA;
 }
 
 static void imx_poll_put_char(struct uart_port *port, unsigned char c)
 {
-	struct imx_port_ucrs old_ucr;
 	unsigned int status;
 
-	/* save control registers */
-	imx_port_ucrs_save(port, &old_ucr);
-
-	/* disable interrupts */
-	writel(UCR1_UARTEN, port->membase + UCR1);
-	writel(old_ucr.ucr2 & ~(UCR2_ATEN | UCR2_RTSEN | UCR2_ESCI),
-	       port->membase + UCR2);
-	writel(old_ucr.ucr3 & ~(UCR3_DCD | UCR3_RI | UCR3_DTREN),
-	       port->membase + UCR3);
-
 	/* drain */
 	do {
-		status = readl(port->membase + USR1);
+		status = readl_relaxed(port->membase + USR1);
 	} while (~status & USR1_TRDY);
 
 	/* write */
-	writel(c, port->membase + URTX0);
+	writel_relaxed(c, port->membase + URTX0);
 
 	/* flush */
 	do {
-		status = readl(port->membase + USR2);
+		status = readl_relaxed(port->membase + USR2);
 	} while (~status & USR2_TXDC);
-
-	/* restore control registers */
-	imx_port_ucrs_restore(port, &old_ucr);
 }
 #endif
 
@@ -1563,6 +1593,9 @@  static struct uart_ops imx_pops = {
 	.config_port	= imx_config_port,
 	.verify_port	= imx_verify_port,
 #if defined(CONFIG_CONSOLE_POLL)
+#if defined(CONFIG_KGDB_FIQ)
+	.poll_init      = imx_poll_init,
+#endif
 	.poll_get_char  = imx_poll_get_char,
 	.poll_put_char  = imx_poll_put_char,
 #endif