diff mbox

[05/18] tty: serial: 8250_core: read only RX if there is something in the FIFO

Message ID 1409943773-7874-6-git-send-email-bigeasy@linutronix.de (mailing list archive)
State New, archived
Headers show

Commit Message

Sebastian Andrzej Siewior Sept. 5, 2014, 7:02 p.m. UTC 
The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:

|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
|Control: 10c5387d  Table: 80004019  DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
---
 drivers/tty/serial/8250/8250_core.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
diff mbox

Patch

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index f9dd20ebab52..eaab8974a456 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2086,8 +2086,8 @@  int serial8250_do_startup(struct uart_port *port)
 	/*
 	 * Clear the interrupt registers.
 	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 
@@ -2248,8 +2248,8 @@  int serial8250_do_startup(struct uart_port *port)
 	 * saved flags to avoid getting false values from polling
 	 * routines or the previous session.
 	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 	up->lsr_saved_flags = 0;
@@ -2342,7 +2342,8 @@  void serial8250_do_shutdown(struct uart_port *port)
 	 * Read data port to reset things, and then unlink from
 	 * the IRQ chain.
 	 */
-	serial_port_in(port, UART_RX);
+	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
+		serial_port_in(port, UART_RX);
 	serial8250_rpm_put(up);
 
 	del_timer_sync(&up->timer);