new file mode 100644
@@ -0,0 +1,31 @@
+Broadcom Cygnus device tree bindings
+------------------------------------
+
+
+Boards with Cygnus SoCs shall have the following properties:
+
+Required root node property:
+
+BCM11300
+compatible = "brcm,bcm11300", "brcm,cygnus";
+
+BCM11320
+compatible = "brcm,bcm11320", "brcm,cygnus";
+
+BCM11350
+compatible = "brcm,bcm11350", "brcm,cygnus";
+
+BCM11360
+compatible = "brcm,bcm11360", "brcm,cygnus";
+
+BCM58300
+compatible = "brcm,bcm58300", "brcm,cygnus";
+
+BCM58302
+compatible = "brcm,bcm58302", "brcm,cygnus";
+
+BCM58303
+compatible = "brcm,bcm58303", "brcm,cygnus";
+
+BCM58305
+compatible = "brcm,bcm58305", "brcm,cygnus";
new file mode 100644
@@ -0,0 +1,121 @@
+Broadcom Cygnus Clock Controller
+
+This binding uses the common clock binding:
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The Cygnus clock controller manages several PLL's and their channels, found only
+on the Cygnus chip. Clocks that are common to iProc can be found in the iProc
+clock controller. The controllers are split into a parent-child relationship
+where the parent is the PLL and the child controls the PLL's channels.
+
+All PLL's are derived from a 25MHz oscillator. The PLL's controlled are the
+GENPLL, LCPLL, the MIPI PLL. In addition, there are two clocks derived from
+GENPLL channel 0, and three that are derived directly from the oscillator.
+
+Required properties:
+- compatible: Must be one of the following:
+ "brcm,cygnus-lcpll-clk" - Controls LCPLL.
+ "brcm,cygnus-lcpll-ch" - Controls LCPLL (parent) channels
+ "brcm,cygnus-genpll-clk" - Controls parent GENPLL
+ "brcm,cygnus-genpll-ch" - Controls GENPLL (parent) channels
+ "brcm,cygnus-mipipll-clk" - Controls MIPI PLL
+ "brcm,cygnus-mipipll-ch" - Controls parent MIPI PLL (parent) channels
+ "brcm,cygnus-osc-derived" - Controls oscillator (parent) derived channels
+ not controlled by any PLL.
+ "brcm,cygnus-pll-derived" - Controls clocks derived from GENPLL channel 0.
+ These clocks have hard wired internal dividers and their clock rates
+ scale according to the GENPLL channel.
+
+- reg: First register is the base address of the PLL. Register 2 and 3 are
+ required by some clocks. They are the top clock gating control used to
+ enable/disable clocks (ch 1), and the CRMU PLL AON CONTROL register which
+ powers on PLL/LDO's (ch 2).
+
+- clocks: The input parent clock phandle for the clock. This is either a PLL,
+ oscillator, or GENPLL channel 0.
+
+- channel: The PLL channel that the clock belongs to. This is used for
+ "brcm,cygnus-lcpll-ch", "brcm,cygnus-genpll-ch", "brcm,cygnus-mipipll-ch",
+ "brcm,cygnus-osc-derived" only.
+
+- div: Used by "brcm,cygnus-pll-derived" to define the hard coded internal
+ divider value. Used by "brcm,cygnus-osc-derived" to specify the programmable
+ divider.
+
+- #clock-cells: From common clock binding; shall be set to 0.
+
+Examples:
+
+ osc: oscillator {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ lcpll: lcpll@0301d02c {
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-lcpll-clk";
+ reg = <0x0301d02c 0x1c>;
+ clocks = <&osc>;
+ };
+
+ genpll: genpll@0301d000 {
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-genpll-clk";
+ reg = <0x0301d000 0x2c>,
+ <0x180AA024 0x4>,
+ <0x0301C020 0x4>;
+ clocks = <&osc>;
+ };
+
+ axi21_clk: genpll_ch0@0301d000 {
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-genpll-ch";
+ reg = <0x0301d000 0x2c>;
+ clocks = <&genpll>;
+ channel = <0>;
+ };
+
+ pcie_clk: lcpll_ch0@0301d02c {
+ compatible = "brcm,cygnus-lcpll-ch";
+ reg = <0x0301d02c 0x1c>;
+ #clock-cells = <0>;
+ clocks = <&lcpll>;
+ channel = <0>;
+ };
+
+ axi41_clk: axi41_clk {
+ reg = <0x0301d000 0x2c>;
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-pll-derived";
+ clocks = <&axi21_clk>;
+ div = <2>;
+ };
+
+ keypad_clk: keypad_clk@0301D048 {
+ compatible = "brcm,cygnus-osc-derived";
+ reg = <0x0301D048 0x4>,
+ <0x180AA024 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc>;
+ channel = <0>;
+ div = <392>;
+ };
+
+ mipipll: mipipll@180a9800 {
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-mipipll-clk";
+ reg = <0x180a9800 0x2c>,
+ top_clk_gating_ctrl: <0x180AA024 0x4>,
+ crmu_pll_aon_ctrl: <0x0301C020 0x4>;
+ clocks = <&osc>;
+ };
+
+ lcd_clk: mipipll_ch1@180a9800 {
+ #clock-cells = <0>;
+ compatible = "brcm,cygnus-mipipll-ch";
+ reg = <0x180a9800 0x2c>,
+ <0x180AA024 0x4>;
+ clocks = <&mipipll>;
+ channel = <1>;
+ };
new file mode 100644
@@ -0,0 +1,48 @@
+Broadcom iProc Clock Controller
+
+This binding uses the common clock binding:
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The iProc clock controller manages clocks that are common to iProc chips.
+The controllers are split into a parent-child relationship where the parent is
+the PLL and the child controls the PLL's channels.
+
+The only PLL controlled is the ARM PLL which is derived from a 25MHz crystal.
+
+Required properties:
+- compatible: Must be one of the following:
+ "brcm,iproc-arm-a9pll" - Controls ARM PLL.
+ "brcm,iproc-arm-ch" - Controls ARM PLL (parent) channels
+
+- reg: The base address of the PLL.
+
+- clocks: The input parent clock phandle for the clock. This is either a PLL,
+ or oscillator.
+
+- channel: The PLL channel that the clock belongs to. This is used for
+ "brcm,iproc-arm-ch" only.
+
+- #clock-cells: From common clock binding; shall be set to 0.
+
+Example:
+
+ osc: oscillator {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ a9pll: arm_clk@19000000 {
+ compatible = "brcm,iproc-arm-a9pll";
+ reg = <0x19000000 0x1000>;
+ #clock-cells = <0>;
+ clocks = <&osc>;
+ };
+
+ periph_clk: periph_clk@19000000 {
+ compatible = "brcm,iproc-arm-ch";
+ reg = <0x19000000 0x1000>;
+ #clock-cells = <0>;
+ clocks = <&a9pll>;
+ channel = <3>;
+ };