diff mbox

arm: perf: Directly handle SMP platforms with one SPI

Message ID 1416581603-30557-1-git-send-email-daniel.thompson@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Daniel Thompson Nov. 21, 2014, 2:53 p.m. UTC
Some ARM platforms mux the PMU interrupt of every core into a single
SPI. On such platforms if the PMU of any core except 0 raises an interrupt
then it cannot be serviced and eventually, if you are lucky, the spurious
irq detection might forcefully disable the interrupt.

On these SoCs it is not possible to determine which core raised the
interrupt so workaround this issue by queuing irqwork on the other
cores whenever the primary interrupt handler is unable to service the
interrupt.

The u8500 platform has an alternative workaround that dynamically alters
the affinity of the PMU interrupt. This workaround logic is no longer
required so the original code is removed as is the hook it relied upon.

Tested on imx6q (which has fours cores/PMUs all muxed to a single SPI).

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
---

Notes:
    Thanks to Lucas Stach, Russell King and Thomas Gleixner for critiquing
    an older, completely different way to tackle the same problem.
    

 arch/arm/include/asm/pmu.h       | 10 +++++
 arch/arm/kernel/perf_event.c     | 11 ++---
 arch/arm/kernel/perf_event_cpu.c | 94 ++++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-ux500/cpu-db8500.c | 29 -------------
 4 files changed, 107 insertions(+), 37 deletions(-)

--
1.9.3

Comments

Linus Walleij Dec. 2, 2014, 1:22 p.m. UTC | #1
On Fri, Nov 21, 2014 at 3:53 PM, Daniel Thompson
<daniel.thompson@linaro.org> wrote:

> Some ARM platforms mux the PMU interrupt of every core into a single
> SPI. On such platforms if the PMU of any core except 0 raises an interrupt
> then it cannot be serviced and eventually, if you are lucky, the spurious
> irq detection might forcefully disable the interrupt.
>
> On these SoCs it is not possible to determine which core raised the
> interrupt so workaround this issue by queuing irqwork on the other
> cores whenever the primary interrupt handler is unable to service the
> interrupt.
>
> The u8500 platform has an alternative workaround that dynamically alters
> the affinity of the PMU interrupt. This workaround logic is no longer
> required so the original code is removed as is the hook it relied upon.
>
> Tested on imx6q (which has fours cores/PMUs all muxed to a single SPI).
>
> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>

After som pain I managed to compile and test this with perf.
Works like a charm.

Tested-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
diff mbox

Patch

diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h
index 0b648c541293..36472c3cc283 100644
--- a/arch/arm/include/asm/pmu.h
+++ b/arch/arm/include/asm/pmu.h
@@ -81,6 +81,12 @@  struct pmu_hw_events {
 	raw_spinlock_t		pmu_lock;
 };

+struct arm_pmu_work {
+	struct irq_work work;
+	struct arm_pmu *arm_pmu;
+	atomic_t ret;
+};
+
 struct arm_pmu {
 	struct pmu	pmu;
 	cpumask_t	active_irqs;
@@ -101,6 +107,7 @@  struct arm_pmu {
 	void		(*reset)(void *);
 	int		(*request_irq)(struct arm_pmu *, irq_handler_t handler);
 	void		(*free_irq)(struct arm_pmu *);
+	irqreturn_t	(*handle_irq_none)(struct arm_pmu *);
 	int		(*map_event)(struct perf_event *event);
 	int		num_events;
 	atomic_t	active_events;
@@ -108,6 +115,9 @@  struct arm_pmu {
 	u64		max_period;
 	struct platform_device	*plat_device;
 	struct pmu_hw_events	*(*get_hw_events)(void);
+	int             single_irq;
+	struct arm_pmu_work __percpu *work;
+	atomic_t        remaining_work;
 };

 #define to_arm_pmu(p) (container_of(p, struct arm_pmu, pmu))
diff --git a/arch/arm/kernel/perf_event.c b/arch/arm/kernel/perf_event.c
index b50a770f8c99..0792c913b9bb 100644
--- a/arch/arm/kernel/perf_event.c
+++ b/arch/arm/kernel/perf_event.c
@@ -306,22 +306,17 @@  validate_group(struct perf_event *event)
 static irqreturn_t armpmu_dispatch_irq(int irq, void *dev)
 {
 	struct arm_pmu *armpmu;
-	struct platform_device *plat_device;
-	struct arm_pmu_platdata *plat;
 	int ret;
 	u64 start_clock, finish_clock;

 	if (irq_is_percpu(irq))
 		dev = *(void **)dev;
 	armpmu = dev;
-	plat_device = armpmu->plat_device;
-	plat = dev_get_platdata(&plat_device->dev);

 	start_clock = sched_clock();
-	if (plat && plat->handle_irq)
-		ret = plat->handle_irq(irq, dev, armpmu->handle_irq);
-	else
-		ret = armpmu->handle_irq(irq, dev);
+	ret = armpmu->handle_irq(irq, dev);
+	if (ret == IRQ_NONE && armpmu->handle_irq_none)
+		ret = armpmu->handle_irq_none(dev);
 	finish_clock = sched_clock();

 	perf_sample_event_took(finish_clock - start_clock);
diff --git a/arch/arm/kernel/perf_event_cpu.c b/arch/arm/kernel/perf_event_cpu.c
index eb2c4d55666b..e7153dc3b489 100644
--- a/arch/arm/kernel/perf_event_cpu.c
+++ b/arch/arm/kernel/perf_event_cpu.c
@@ -88,6 +88,75 @@  static void cpu_pmu_disable_percpu_irq(void *data)
 	disable_percpu_irq(irq);
 }

+/*
+ * Workaround logic that is distributed to all cores if the PMU has only
+ * a single IRQ and the CPU receiving that IRQ cannot handle it. Its
+ * job is to try to service the interrupt on the current CPU. It will
+ * also enable the IRQ again if all the other CPUs have already tried to
+ * service it.
+ */
+static void cpu_pmu_do_percpu_work(struct irq_work *w)
+{
+	struct arm_pmu_work *work = container_of(w, struct arm_pmu_work, work);
+	struct arm_pmu *cpu_pmu = work->arm_pmu;
+
+	atomic_set(&work->ret,
+		   cpu_pmu->handle_irq(cpu_pmu->single_irq, cpu_pmu));
+
+	if (atomic_dec_and_test(&cpu_pmu->remaining_work))
+		enable_irq(cpu_pmu->single_irq);
+}
+
+/*
+ * This callback, which is enabled only on SMP platforms that are
+ * running with a single IRQ, is called when the PMU handler running in
+ * the current CPU cannot service the interrupt.
+ *
+ * It will disable the interrupt and distribute irqwork to all other
+ * processors in the system. Hopefully one of them will clear the
+ * interrupt...
+ */
+static irqreturn_t cpu_pmu_handle_irq_none(struct arm_pmu *cpu_pmu)
+{
+	int num_online = num_online_cpus();
+	irqreturn_t ret = IRQ_NONE;
+	int cpu, cret;
+
+	if (num_online <= 1)
+		return IRQ_NONE;
+
+	disable_irq_nosync(cpu_pmu->single_irq);
+	atomic_add(num_online, &cpu_pmu->remaining_work);
+	smp_mb__after_atomic();
+
+	for_each_online_cpu(cpu) {
+		struct arm_pmu_work *work = per_cpu_ptr(cpu_pmu->work, cpu);
+
+		if (cpu == smp_processor_id())
+			continue;
+
+		/*
+		 * We can be extremely relaxed about memory ordering
+		 * here. All we are doing is gathering information
+		 * about the past to help us give a return value that
+		 * will keep the spurious interrupt detector both happy
+		 * *and* functional. We are not shared so we can
+		 * tolerate the occasional spurious IRQ_HANDLED.
+		 */
+		cret = atomic_read(&work->ret);
+		if (cret != IRQ_NONE)
+			ret = cret;
+
+		if (!irq_work_queue_on(&work->work, cpu))
+			atomic_dec(&cpu_pmu->remaining_work);
+	}
+
+	if (atomic_dec_and_test(&cpu_pmu->remaining_work))
+		enable_irq(cpu_pmu->single_irq);
+
+	return ret;
+}
+
 static void cpu_pmu_free_irq(struct arm_pmu *cpu_pmu)
 {
 	int i, irq, irqs;
@@ -107,6 +176,9 @@  static void cpu_pmu_free_irq(struct arm_pmu *cpu_pmu)
 			if (irq >= 0)
 				free_irq(irq, cpu_pmu);
 		}
+
+		cpu_pmu->handle_irq_none = cpu_pmu_handle_irq_none;
+		free_percpu(cpu_pmu->work);
 	}
 }

@@ -162,6 +234,28 @@  static int cpu_pmu_request_irq(struct arm_pmu *cpu_pmu, irq_handler_t handler)

 			cpumask_set_cpu(i, &cpu_pmu->active_irqs);
 		}
+
+		/*
+		 * If we are running SMP and have only one interrupt source
+		 * then get ready to share that single irq among the cores.
+		 */
+		if (nr_cpu_ids > 1 && irqs == 1) {
+			cpu_pmu->single_irq = platform_get_irq(pmu_device, 0);
+			cpu_pmu->work = alloc_percpu(struct arm_pmu_work);
+			if (!cpu_pmu->work) {
+				pr_err("no memory for shared IRQ workaround\n");
+				return -ENOMEM;
+			}
+
+			for_each_possible_cpu(i) {
+				struct arm_pmu_work *w =
+				    per_cpu_ptr(cpu_pmu->work, i);
+				init_irq_work(&w->work, cpu_pmu_do_percpu_work);
+				w->arm_pmu = cpu_pmu;
+			}
+
+			cpu_pmu->handle_irq_none = cpu_pmu_handle_irq_none;
+		}
 	}

 	return 0;
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 6f63954c8bde..917774999c5c 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -12,8 +12,6 @@ 
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/amba/bus.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/mfd/abx500/ab8500.h>
@@ -23,7 +21,6 @@ 
 #include <linux/regulator/machine.h>
 #include <linux/random.h>

-#include <asm/pmu.h>
 #include <asm/mach/map.h>

 #include "setup.h"
@@ -99,30 +96,6 @@  static void __init u8500_map_io(void)
 		iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));
 }

-/*
- * The PMU IRQ lines of two cores are wired together into a single interrupt.
- * Bounce the interrupt to the other core if it's not ours.
- */
-static irqreturn_t db8500_pmu_handler(int irq, void *dev, irq_handler_t handler)
-{
-	irqreturn_t ret = handler(irq, dev);
-	int other = !smp_processor_id();
-
-	if (ret == IRQ_NONE && cpu_online(other))
-		irq_set_affinity(irq, cpumask_of(other));
-
-	/*
-	 * We should be able to get away with the amount of IRQ_NONEs we give,
-	 * while still having the spurious IRQ detection code kick in if the
-	 * interrupt really starts hitting spuriously.
-	 */
-	return ret;
-}
-
-static struct arm_pmu_platdata db8500_pmu_platdata = {
-	.handle_irq		= db8500_pmu_handler,
-};
-
 static const char *db8500_read_soc_id(void)
 {
 	void __iomem *uid = __io_address(U8500_BB_UID_BASE);
@@ -143,8 +116,6 @@  static struct device * __init db8500_soc_device_init(void)
 }

 static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
-	/* Requires call-back bindings. */
-	OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
 	/* Requires DMA bindings. */
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
 		       "ux500-msp-i2s.0", &msp0_platform_data),