@@ -73,6 +73,9 @@ static int dw_mci_rockchip_init(struct dw_mci *host)
/* It is slot 8 on Rockchip SoCs */
host->sdio_id0 = 8;
+ /* It needs this quirk on all Rockchip SoCs */
+ host->pdata->quirks |= DW_MCI_QUIRK_BROKEN_DTO;
+
return 0;
}
@@ -1464,6 +1464,8 @@ static void dw_mci_tasklet_func(unsigned long priv)
enum dw_mci_state state;
enum dw_mci_state prev_state;
unsigned int err;
+ unsigned int drto_clks;
+ unsigned int drto_ms;
spin_lock(&host->lock);
@@ -1529,8 +1531,17 @@ static void dw_mci_tasklet_func(unsigned long priv)
}
if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
- &host->pending_events))
+ &host->pending_events)) {
+ if (host->quirks & DW_MCI_QUIRK_BROKEN_DTO) {
+ drto_clks = mci_readl(host, TMOUT) >> 8;
+ drto_ms = DIV_ROUND_UP(drto_clks * 1000,
+ host->bus_hz);
+
+ mod_timer(&host->dto_timer, jiffies +
+ msecs_to_jiffies(drto_ms));
+ }
break;
+ }
set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
@@ -2122,6 +2133,9 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
}
if (pending & SDMMC_INT_DATA_OVER) {
+ if (host->quirks & DW_MCI_QUIRK_BROKEN_DTO)
+ del_timer(&host->dto_timer);
+
mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
if (!host->data_status)
host->data_status = pending;
@@ -2509,6 +2523,28 @@ ciu_out:
return ret;
}
+static void dw_mci_dto_timer(unsigned long arg)
+{
+ struct dw_mci *host = (struct dw_mci *)arg;
+
+ switch (host->state) {
+ case STATE_SENDING_DATA:
+ case STATE_DATA_BUSY:
+ /*
+ * If DTO interrupt does NOT come in sending data state,
+ * we should notify the driver to terminate current transfer
+ * and report a data timeout to the core.
+ */
+ host->data_status = SDMMC_INT_DRTO;
+ set_bit(EVENT_DATA_ERROR, &host->pending_events);
+ set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ break;
+ default:
+ break;
+ }
+}
+
#ifdef CONFIG_OF
static struct dw_mci_of_quirks {
char *quirk;
@@ -2661,6 +2697,9 @@ int dw_mci_probe(struct dw_mci *host)
spin_lock_init(&host->lock);
INIT_LIST_HEAD(&host->queue);
+ if (host->quirks & DW_MCI_QUIRK_BROKEN_DTO)
+ setup_timer(&host->dto_timer,
+ dw_mci_dto_timer, (unsigned long)host);
/*
* Get the host data width - this assumes that HCON has been set with
@@ -98,6 +98,7 @@ struct mmc_data;
* @irq_flags: The flags to be passed to request_irq.
* @irq: The irq value to be passed to request_irq.
* @sdio_id0: Number of slot0 in the SDIO interrupt registers.
+ * @dto_timer: Timer for broken data transfer over scheme.
*
* Locking
* =======
@@ -196,6 +197,8 @@ struct dw_mci {
int irq;
int sdio_id0;
+
+ struct timer_list dto_timer;
};
/* DMA ops for Internal/External DMAC interface */
@@ -220,6 +223,8 @@ struct dw_mci_dma_ops {
#define DW_MCI_QUIRK_BROKEN_CARD_DETECTION BIT(3)
/* No write protect */
#define DW_MCI_QUIRK_NO_WRITE_PROTECT BIT(4)
+/* Timer for broken data transfer over scheme */
+#define DW_MCI_QUIRK_BROKEN_DTO BIT(5)
/* Slot level quirks */
/* This slot has no write protect */
This patch add a new quirk to add a s/w timer to notify the driver to terminate current transfer and report a data timeout to the core, if DTO interrupt does NOT come within the given time. dw_mmc call mmc_request_done func to finish transfer depends on DTO interrupt. If DTO interrupt does not come in sending data state, the current transfer will be blocked. But this case really exists, when driver reads tuning data from card on RK3288-pink2 board. I measured waveforms by oscilloscope and found that card clock was always on and data lines were always holded high level in sending data state. We got the reply from synopsys: There are two counters but both use the same value of [31:8] bits. Data timeout counter doesn't wait for stop clock and you should get DRTO even when the clock is not stopped. Host Starvation timeout counter is triggered with stop clock condition. This means that host should get DRTO and DTO interrupt. But we really don't get any data-related interrupt in RK3X SoCs. And driver can't get data transfer state, it can do nothing but wait for. We don't know why we have this problem, but we need it to fix this problem now. And I will post a follow up change when we find the root cause. Signed-off-by: Addy Ke <addy.ke@rock-chips.com> --- Changes in v2: - fix some typo. - remove extra timeout value (250ms). - remove dw_mci_dto_start_monitor func. - use "broken-dto" for new quirk and change Subject for it. Changes in v3: - Remove dts for broken-dto, just add this quirk in dw_mci_rockchip_init drivers/mmc/host/dw_mmc-rockchip.c | 3 +++ drivers/mmc/host/dw_mmc.c | 41 +++++++++++++++++++++++++++++++++++++- include/linux/mmc/dw_mmc.h | 5 +++++ 3 files changed, 48 insertions(+), 1 deletion(-)