diff mbox

[4/4] usb: phy: add phy-hi6220

Message ID 1423147620-5760-5-git-send-email-zhangfei.gao@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Zhangfei Gao Feb. 5, 2015, 2:47 p.m. UTC 
Add usb phy controller for hi6220 platform

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
---
 drivers/usb/phy/Kconfig      |   9 ++
 drivers/usb/phy/Makefile     |   1 +
 drivers/usb/phy/phy-hi6220.c | 290 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 300 insertions(+)
 create mode 100644 drivers/usb/phy/phy-hi6220.c

Comments

Peter Chen Feb. 6, 2015, 8:41 a.m. UTC | #1 
On Thu, Feb 05, 2015 at 10:47:00PM +0800, Zhangfei Gao wrote:
> Add usb phy controller for hi6220 platform
> 
> Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
> ---
>  drivers/usb/phy/Kconfig      |   9 ++
>  drivers/usb/phy/Makefile     |   1 +
>  drivers/usb/phy/phy-hi6220.c | 290 +++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 300 insertions(+)
>  create mode 100644 drivers/usb/phy/phy-hi6220.c
> 
> diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
> index c6d0c8e..405a3d0 100644
> --- a/drivers/usb/phy/Kconfig
> +++ b/drivers/usb/phy/Kconfig
> @@ -173,6 +173,15 @@ config USB_MXS_PHY
>  
>  	  MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
>  
> +config USB_HI6220_PHY
> +	tristate "hi6220 USB PHY support"
> +	select USB_PHY
> +	select MFD_SYSCON
> +	help
> +	  Enable this to support the HISILICON HI6220 USB PHY.
> +
> +	  To compile this driver as a module, choose M here.
> +
>  config USB_RCAR_PHY
>  	tristate "Renesas R-Car USB PHY support"
>  	depends on USB || USB_GADGET
> diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
> index 75f2bba..819283c 100644
> --- a/drivers/usb/phy/Makefile
> +++ b/drivers/usb/phy/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_SAMSUNG_USBPHY)		+= phy-samsung-usb.o
>  obj-$(CONFIG_TWL6030_USB)		+= phy-twl6030-usb.o
>  obj-$(CONFIG_USB_EHCI_TEGRA)		+= phy-tegra-usb.o
>  obj-$(CONFIG_USB_GPIO_VBUS)		+= phy-gpio-vbus-usb.o
> +obj-$(CONFIG_USB_HI6220_PHY)		+= phy-hi6220.o

To align the naming method, phy-hi6220-usb is better.

>  obj-$(CONFIG_USB_ISP1301)		+= phy-isp1301.o
>  obj-$(CONFIG_USB_MSM_OTG)		+= phy-msm-usb.o
>  obj-$(CONFIG_USB_MV_OTG)		+= phy-mv-usb.o
> diff --git a/drivers/usb/phy/phy-hi6220.c b/drivers/usb/phy/phy-hi6220.c
> new file mode 100644
> index 0000000..87b1f0e
> --- /dev/null
> +++ b/drivers/usb/phy/phy-hi6220.c
> @@ -0,0 +1,290 @@
> +/*
> + * Copyright (c) 2015 Linaro Ltd.
> + * Copyright (c) 2015 Hisilicon Limited.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of_gpio.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/usb/gadget.h>
> +#include <linux/usb/otg.h>
> +
> +#define SC_PERIPH_CTRL4			0x00c
> +
> +#define PERIPH_CTRL4_PICO_SIDDQ		BIT(6)
> +#define PERIPH_CTRL4_PICO_OGDISABLE	BIT(8)
> +#define PERIPH_CTRL4_PICO_VBUSVLDEXT	BIT(10)
> +#define PERIPH_CTRL4_PICO_VBUSVLDEXTSEL	BIT(11)
> +#define PERIPH_CTRL4_OTG_PHY_SEL	BIT(21)
> +
> +#define SC_PERIPH_CTRL5			0x010
> +
> +#define PERIPH_CTRL5_USBOTG_RES_SEL	BIT(3)
> +#define PERIPH_CTRL5_PICOPHY_ACAENB	BIT(4)
> +#define PERIPH_CTRL5_PICOPHY_BC_MODE	BIT(5)
> +#define PERIPH_CTRL5_PICOPHY_CHRGSEL	BIT(6)
> +#define PERIPH_CTRL5_PICOPHY_VDATSRCEND	BIT(7)
> +#define PERIPH_CTRL5_PICOPHY_VDATDETENB	BIT(8)
> +#define PERIPH_CTRL5_PICOPHY_DCDENB	BIT(9)
> +#define PERIPH_CTRL5_PICOPHY_IDDIG	BIT(10)
> +
> +#define SC_PERIPH_CTRL8			0x018
> +
> +#define EYE_PATTERN_PARA		0x7053348c
> +
> +#define SC_PERIPH_RSTDIS0		0x304
> +
> +#define PERIPH_RSTDIS0_USBOTG_BUS	BIT(4)
> +#define PERIPH_RSTDIS0_POR_PICOPHY	BIT(5)
> +#define PERIPH_RSTDIS0_USBOTG		BIT(6)
> +#define PERIPH_RSTDIS0_USBOTG_32K	BIT(7)
> +
> +enum usb_mode {
> +	USB_EMPTY,
> +	GADGET_DEVICE,
> +	OTG_HOST,
> +};

This usb_mode is a little strange, what state you would like to
use?

> +
> +struct hi6220_priv {
> +	struct usb_phy phy;
> +	struct delayed_work work;
> +	struct regmap *reg;
> +	struct clk *clk;
> +	struct regulator *vcc;
> +	int gpio_vbus_det;
> +	int gpio_id_det;
> +	enum usb_mode mode;
> +};
> +
> +static void hi6220_start_periphrals(struct hi6220_priv *priv, bool on)
> +{
> +	struct usb_otg *otg = priv->phy.otg;
> +
> +	if (!otg->gadget)
> +		return;
> +
> +	if (on)
> +		usb_gadget_connect(otg->gadget);
> +	else
> +		usb_gadget_disconnect(otg->gadget);
> +}
> +
> +static void hi6220_detect_work(struct work_struct *work)
> +{
> +	struct hi6220_priv *priv =
> +		container_of(work, struct hi6220_priv, work.work);
> +	int id_det, vbus_det;
> +	enum usb_mode mode;
> +
> +	if (!gpio_is_valid(priv->gpio_id_det) ||
> +	    !gpio_is_valid(priv->gpio_vbus_det))
> +		return;
> +
> +	id_det = gpio_get_value_cansleep(priv->gpio_id_det);
> +	vbus_det = gpio_get_value_cansleep(priv->gpio_vbus_det);
> +
> +	if (vbus_det == 0) {
> +		if (id_det == 1)
> +			mode = GADGET_DEVICE;
> +		else
> +			mode = OTG_HOST;
> +	} else {
> +		mode = USB_EMPTY;
> +	}
> +
> +	if (mode == GADGET_DEVICE && priv->mode == USB_EMPTY)
> +		hi6220_start_periphrals(priv, true);
> +	if (mode == USB_EMPTY && priv->mode == GADGET_DEVICE)
> +		hi6220_start_periphrals(priv, false);
> +
> +	priv->mode = mode;
> +}
> +
> +static irqreturn_t hiusb_gpio_intr(int irq, void *data)
> +{
> +	struct hi6220_priv *priv = (struct hi6220_priv *)data;
> +
> +	/* add debounce time */
> +	schedule_delayed_work(&priv->work, msecs_to_jiffies(100));
> +	return IRQ_HANDLED;
> +}
> +
> +static int mv_otg_set_peripheral(struct usb_otg *otg,

mv? You may want to use hi

> +				 struct usb_gadget *gadget)
> +{
> +	struct hi6220_priv *priv;
> +
> +	priv = container_of(otg->usb_phy, struct hi6220_priv, phy);
> +	otg->gadget = gadget;
> +	return 0;
> +}
> +
> +static void hi6220_phy_setup(struct hi6220_priv *priv)
> +{
> +	u32 val, mask;
> +	int ret;
> +
> +	if (priv->reg == NULL)
> +		return;
> +
> +	val = PERIPH_RSTDIS0_USBOTG_BUS | PERIPH_RSTDIS0_POR_PICOPHY |
> +	      PERIPH_RSTDIS0_USBOTG | PERIPH_RSTDIS0_USBOTG_32K;
> +	mask = val;
> +	ret = regmap_update_bits(priv->reg, SC_PERIPH_RSTDIS0, mask, val);
> +	if (ret)
> +		return;
> +
> +	ret = regmap_read(priv->reg, SC_PERIPH_CTRL5, &val);
> +	val = PERIPH_CTRL5_USBOTG_RES_SEL | PERIPH_CTRL5_PICOPHY_ACAENB;
> +	mask = val | PERIPH_CTRL5_PICOPHY_BC_MODE;
> +	ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL5, mask, val);
> +	if (ret)
> +		return;
> +
> +	val =  PERIPH_CTRL4_PICO_VBUSVLDEXT | PERIPH_CTRL4_PICO_VBUSVLDEXTSEL |
> +	       PERIPH_CTRL4_OTG_PHY_SEL;
> +	mask = val | PERIPH_CTRL4_PICO_SIDDQ | PERIPH_CTRL4_PICO_OGDISABLE;
> +	ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL4, mask, val);
> +	if (ret)
> +		return;
> +
> +	ret = regmap_write(priv->reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
> +	if (ret)
> +		return;
> +}
> +
> +static int hi6220_phy_probe(struct platform_device *pdev)
> +{
> +	struct hi6220_priv *priv;
> +	struct usb_otg *otg;
> +	struct device_node *np = pdev->dev.of_node;
> +	int ret, irq;
> +
> +	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
> +	if (!otg)
> +		return -ENOMEM;
> +
> +	priv->phy.dev = &pdev->dev;
> +	priv->phy.otg = otg;
> +	priv->phy.label = "hi6220";
> +	platform_set_drvdata(pdev, priv);
> +	otg->set_peripheral = mv_otg_set_peripheral;
> +
> +	priv->gpio_vbus_det = of_get_named_gpio(np, "hisilicon,gpio_vbus_det", 0);
> +	if (priv->gpio_vbus_det == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +	if (!gpio_is_valid(priv->gpio_vbus_det)) {
> +		dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_vbus_det);
> +		return -ENODEV;
> +	}
> +
> +	priv->gpio_id_det = of_get_named_gpio(np, "hisilicon,gpio_id_det", 0);
> +	if (priv->gpio_id_det == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +	if (!gpio_is_valid(priv->gpio_id_det)) {
> +		dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_id_det);
> +		return -ENODEV;
> +	}
> +
> +	priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> +					"hisilicon,peripheral-syscon");
> +	if (IS_ERR(priv->reg))
> +		priv->reg = NULL;

You may differentiate -ENODEV and other errors, for other errors, you 
can show an error, and return directly.

> +
> +	INIT_DELAYED_WORK(&priv->work, hi6220_detect_work);
> +
> +	ret = devm_gpio_request_one(&pdev->dev, priv->gpio_vbus_det,
> +				    GPIOF_IN, "gpio_vbus_det");
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "gpio request failed for gpio_vbus_det\n");
> +		return ret;
> +	}
> +
> +	ret = devm_gpio_request_one(&pdev->dev, priv->gpio_id_det,
> +				    GPIOF_IN, "gpio_id_det");
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "gpio request failed for gpio_id_det\n");
> +		return ret;
> +	}
> +
> +	priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
> +	if (!IS_ERR(priv->vcc)) {
> +		ret = regulator_enable(priv->vcc);
> +		if (ret) {
> +			dev_err(&pdev->dev, "Failed to enable regulator\n");
> +			return -ENODEV;
> +		}
> +	}
> +
> +	priv->clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(priv->clk)) {
> +		regulator_disable(priv->vcc);
> +		return PTR_ERR(priv->clk);
> +	}
> +	clk_prepare_enable(priv->clk);
> +
> +	irq = gpio_to_irq(priv->gpio_vbus_det);
> +	ret = devm_request_irq(&pdev->dev, gpio_to_irq(priv->gpio_vbus_det),
> +			       hiusb_gpio_intr, IRQF_NO_SUSPEND |
> +			       IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
> +			       "vbus_gpio_intr", priv);
> +	if (ret) {
> +		dev_err(&pdev->dev, "request gpio irq failed.\n");
> +		goto err_irq;
> +	}

You may put the devm_request_irq to the last, in case, the unexpected
interrupt occurs during the setup.

> +
> +	hi6220_phy_setup(priv);
> +	ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);

Use usb_add_phy_dev please, see the doc for usb_add_phy.

> +	if (ret) {
> +		dev_err(&pdev->dev, "Can't register transceiver\n");
> +		goto err_irq;
> +	}
> +	schedule_delayed_work(&priv->work, 0);
> +
> +	return 0;
> +err_irq:
> +	clk_disable_unprepare(priv->clk);
> +	regulator_disable(priv->vcc);
> +	return ret;
> +}
> +
> +static int hi6220_phy_remove(struct platform_device *pdev)
> +{
> +	struct hi6220_priv *priv = platform_get_drvdata(pdev);
> +
> +	clk_disable_unprepare(priv->clk);
> +	regulator_disable(priv->vcc);
> +	return 0;
> +}
> +
> +static const struct of_device_id hi6220_phy_of_match[] = {
> +	{.compatible = "hisilicon,hi6220-usb-phy",},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, hi6220_phy_of_match);
> +
> +static struct platform_driver hi6220_phy_driver = {
> +	.probe	= hi6220_phy_probe,
> +	.remove	= hi6220_phy_remove,
> +	.driver = {
> +		.name	= "hi6220-usb-phy",
> +		.of_match_table	= hi6220_phy_of_match,
> +	}
> +};
> +module_platform_driver(hi6220_phy_driver);
> +
> +MODULE_DESCRIPTION("HISILICON HI6220 USB PHY driver");
> +MODULE_ALIAS("platform:hi6220-usb-phy");
> +MODULE_LICENSE("GPL");
> --
Zhangfei Gao Feb. 6, 2015, 11:47 a.m. UTC | #2 
On 6 February 2015 at 16:41, Peter Chen <peter.chen@freescale.com> wrote:
> On Thu, Feb 05, 2015 at 10:47:00PM +0800, Zhangfei Gao wrote:

>> @@ -18,6 +18,7 @@ obj-$(CONFIG_SAMSUNG_USBPHY)                += phy-samsung-usb.o
>>  obj-$(CONFIG_TWL6030_USB)            += phy-twl6030-usb.o
>>  obj-$(CONFIG_USB_EHCI_TEGRA)         += phy-tegra-usb.o
>>  obj-$(CONFIG_USB_GPIO_VBUS)          += phy-gpio-vbus-usb.o
>> +obj-$(CONFIG_USB_HI6220_PHY)         += phy-hi6220.o
>
> To align the naming method, phy-hi6220-usb is better.
Sure,


>> +enum usb_mode {
>> +     USB_EMPTY,
>> +     GADGET_DEVICE,
>> +     OTG_HOST,
>> +};
>
> This usb_mode is a little strange, what state you would like to
> use?

it is internal state machine, to distinguish otg gadget mode and host mode.
There are two gpio, we use gpio_vbus interrupt as well as gpio_id
status to distinguish gadget or host.

>> +static irqreturn_t hiusb_gpio_intr(int irq, void *data)
>> +{
>> +     struct hi6220_priv *priv = (struct hi6220_priv *)data;
>> +
>> +     /* add debounce time */
>> +     schedule_delayed_work(&priv->work, msecs_to_jiffies(100));
>> +     return IRQ_HANDLED;
>> +}
>> +
>> +static int mv_otg_set_peripheral(struct usb_otg *otg,
>
> mv? You may want to use hi
Yes, my bad.


>> +static void hi6220_phy_setup(struct hi6220_priv *priv)
>> +{
>> +     u32 val, mask;
>> +     int ret;
>> +
>> +     if (priv->reg == NULL)
>> +             return;
>> +
>> +     val = PERIPH_RSTDIS0_USBOTG_BUS | PERIPH_RSTDIS0_POR_PICOPHY |
>> +           PERIPH_RSTDIS0_USBOTG | PERIPH_RSTDIS0_USBOTG_32K;
>> +     mask = val;
>> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_RSTDIS0, mask, val);
>> +     if (ret)
>> +             return;
>> +
>> +     ret = regmap_read(priv->reg, SC_PERIPH_CTRL5, &val);
>> +     val = PERIPH_CTRL5_USBOTG_RES_SEL | PERIPH_CTRL5_PICOPHY_ACAENB;
>> +     mask = val | PERIPH_CTRL5_PICOPHY_BC_MODE;
>> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL5, mask, val);
>> +     if (ret)
>> +             return;
>> +
>> +     val =  PERIPH_CTRL4_PICO_VBUSVLDEXT | PERIPH_CTRL4_PICO_VBUSVLDEXTSEL |
>> +            PERIPH_CTRL4_OTG_PHY_SEL;
>> +     mask = val | PERIPH_CTRL4_PICO_SIDDQ | PERIPH_CTRL4_PICO_OGDISABLE;
>> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL4, mask, val);
>> +     if (ret)
>> +             return;
>> +
>> +     ret = regmap_write(priv->reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
>> +     if (ret)
>> +             return;
>> +}
>> +
>> +static int hi6220_phy_probe(struct platform_device *pdev)
>> +{
>> +     struct hi6220_priv *priv;
>> +     struct usb_otg *otg;
>> +     struct device_node *np = pdev->dev.of_node;
>> +     int ret, irq;
>> +
>> +     priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>> +     if (!priv)
>> +             return -ENOMEM;
>> +
>> +     otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
>> +     if (!otg)
>> +             return -ENOMEM;
>> +
>> +     priv->phy.dev = &pdev->dev;
>> +     priv->phy.otg = otg;
>> +     priv->phy.label = "hi6220";
>> +     platform_set_drvdata(pdev, priv);
>> +     otg->set_peripheral = mv_otg_set_peripheral;
>> +
>> +     priv->gpio_vbus_det = of_get_named_gpio(np, "hisilicon,gpio_vbus_det", 0);
>> +     if (priv->gpio_vbus_det == -EPROBE_DEFER)
>> +             return -EPROBE_DEFER;
>> +     if (!gpio_is_valid(priv->gpio_vbus_det)) {
>> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_vbus_det);
>> +             return -ENODEV;
>> +     }
>> +
>> +     priv->gpio_id_det = of_get_named_gpio(np, "hisilicon,gpio_id_det", 0);
>> +     if (priv->gpio_id_det == -EPROBE_DEFER)
>> +             return -EPROBE_DEFER;
>> +     if (!gpio_is_valid(priv->gpio_id_det)) {
>> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_id_det);
>> +             return -ENODEV;
>> +     }
>> +
>> +     priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
>> +                                     "hisilicon,peripheral-syscon");
>> +     if (IS_ERR(priv->reg))
>> +             priv->reg = NULL;
>
> You may differentiate -ENODEV and other errors, for other errors, you
> can show an error, and return directly.

Here I want to set this property as optional, in case other platform
do not need this property.
So phy_setup also add protection if (priv->reg == NULL) return;

>
>> +
>> +     INIT_DELAYED_WORK(&priv->work, hi6220_detect_work);
>> +
>> +     ret = devm_gpio_request_one(&pdev->dev, priv->gpio_vbus_det,
>> +                                 GPIOF_IN, "gpio_vbus_det");
>> +     if (ret < 0) {
>> +             dev_err(&pdev->dev, "gpio request failed for gpio_vbus_det\n");
>> +             return ret;
>> +     }
>> +
>> +     ret = devm_gpio_request_one(&pdev->dev, priv->gpio_id_det,
>> +                                 GPIOF_IN, "gpio_id_det");
>> +     if (ret < 0) {
>> +             dev_err(&pdev->dev, "gpio request failed for gpio_id_det\n");
>> +             return ret;
>> +     }
>> +
>> +     priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
>> +     if (!IS_ERR(priv->vcc)) {
>> +             ret = regulator_enable(priv->vcc);
>> +             if (ret) {
>> +                     dev_err(&pdev->dev, "Failed to enable regulator\n");
>> +                     return -ENODEV;
>> +             }
>> +     }
>> +
>> +     priv->clk = devm_clk_get(&pdev->dev, NULL);
>> +     if (IS_ERR(priv->clk)) {
>> +             regulator_disable(priv->vcc);
>> +             return PTR_ERR(priv->clk);
>> +     }
>> +     clk_prepare_enable(priv->clk);
>> +
>> +     irq = gpio_to_irq(priv->gpio_vbus_det);
>> +     ret = devm_request_irq(&pdev->dev, gpio_to_irq(priv->gpio_vbus_det),
>> +                            hiusb_gpio_intr, IRQF_NO_SUSPEND |
>> +                            IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
>> +                            "vbus_gpio_intr", priv);
>> +     if (ret) {
>> +             dev_err(&pdev->dev, "request gpio irq failed.\n");
>> +             goto err_irq;
>> +     }
>
> You may put the devm_request_irq to the last, in case, the unexpected
> interrupt occurs during the setup.
It does not matter, since otg->gadget = NULL.
In fact we manually call schedule_delayed_work to get the gpio status
for setting internal state machine

>
>> +
>> +     hi6220_phy_setup(priv);
>> +     ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
>
> Use usb_add_phy_dev please, see the doc for usb_add_phy.
OK, got it.

Thanks Peter for the review.
Peter Chen Feb. 9, 2015, 1:57 a.m. UTC | #3 
On Fri, Feb 06, 2015 at 07:47:12PM +0800, Zhangfei Gao wrote:
> On 6 February 2015 at 16:41, Peter Chen <peter.chen@freescale.com> wrote:
> > On Thu, Feb 05, 2015 at 10:47:00PM +0800, Zhangfei Gao wrote:
> 
> >> @@ -18,6 +18,7 @@ obj-$(CONFIG_SAMSUNG_USBPHY)                += phy-samsung-usb.o
> >>  obj-$(CONFIG_TWL6030_USB)            += phy-twl6030-usb.o
> >>  obj-$(CONFIG_USB_EHCI_TEGRA)         += phy-tegra-usb.o
> >>  obj-$(CONFIG_USB_GPIO_VBUS)          += phy-gpio-vbus-usb.o
> >> +obj-$(CONFIG_USB_HI6220_PHY)         += phy-hi6220.o
> >
> > To align the naming method, phy-hi6220-usb is better.
> Sure,
> 
> 
> >> +enum usb_mode {
> >> +     USB_EMPTY,
> >> +     GADGET_DEVICE,
> >> +     OTG_HOST,
> >> +};
> >
> > This usb_mode is a little strange, what state you would like to
> > use?
> 
> it is internal state machine, to distinguish otg gadget mode and host mode.
> There are two gpio, we use gpio_vbus interrupt as well as gpio_id
> status to distinguish gadget or host.
> 
> >> +static irqreturn_t hiusb_gpio_intr(int irq, void *data)
> >> +{
> >> +     struct hi6220_priv *priv = (struct hi6220_priv *)data;
> >> +
> >> +     /* add debounce time */
> >> +     schedule_delayed_work(&priv->work, msecs_to_jiffies(100));
> >> +     return IRQ_HANDLED;
> >> +}
> >> +
> >> +static int mv_otg_set_peripheral(struct usb_otg *otg,
> >
> > mv? You may want to use hi
> Yes, my bad.
> 
> 
> >> +static void hi6220_phy_setup(struct hi6220_priv *priv)
> >> +{
> >> +     u32 val, mask;
> >> +     int ret;
> >> +
> >> +     if (priv->reg == NULL)
> >> +             return;
> >> +
> >> +     val = PERIPH_RSTDIS0_USBOTG_BUS | PERIPH_RSTDIS0_POR_PICOPHY |
> >> +           PERIPH_RSTDIS0_USBOTG | PERIPH_RSTDIS0_USBOTG_32K;
> >> +     mask = val;
> >> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_RSTDIS0, mask, val);
> >> +     if (ret)
> >> +             return;
> >> +
> >> +     ret = regmap_read(priv->reg, SC_PERIPH_CTRL5, &val);
> >> +     val = PERIPH_CTRL5_USBOTG_RES_SEL | PERIPH_CTRL5_PICOPHY_ACAENB;
> >> +     mask = val | PERIPH_CTRL5_PICOPHY_BC_MODE;
> >> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL5, mask, val);
> >> +     if (ret)
> >> +             return;
> >> +
> >> +     val =  PERIPH_CTRL4_PICO_VBUSVLDEXT | PERIPH_CTRL4_PICO_VBUSVLDEXTSEL |
> >> +            PERIPH_CTRL4_OTG_PHY_SEL;
> >> +     mask = val | PERIPH_CTRL4_PICO_SIDDQ | PERIPH_CTRL4_PICO_OGDISABLE;
> >> +     ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL4, mask, val);
> >> +     if (ret)
> >> +             return;
> >> +
> >> +     ret = regmap_write(priv->reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
> >> +     if (ret)
> >> +             return;
> >> +}
> >> +
> >> +static int hi6220_phy_probe(struct platform_device *pdev)
> >> +{
> >> +     struct hi6220_priv *priv;
> >> +     struct usb_otg *otg;
> >> +     struct device_node *np = pdev->dev.of_node;
> >> +     int ret, irq;
> >> +
> >> +     priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> >> +     if (!priv)
> >> +             return -ENOMEM;
> >> +
> >> +     otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
> >> +     if (!otg)
> >> +             return -ENOMEM;
> >> +
> >> +     priv->phy.dev = &pdev->dev;
> >> +     priv->phy.otg = otg;
> >> +     priv->phy.label = "hi6220";
> >> +     platform_set_drvdata(pdev, priv);
> >> +     otg->set_peripheral = mv_otg_set_peripheral;
> >> +
> >> +     priv->gpio_vbus_det = of_get_named_gpio(np, "hisilicon,gpio_vbus_det", 0);
> >> +     if (priv->gpio_vbus_det == -EPROBE_DEFER)
> >> +             return -EPROBE_DEFER;
> >> +     if (!gpio_is_valid(priv->gpio_vbus_det)) {
> >> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_vbus_det);
> >> +             return -ENODEV;
> >> +     }
> >> +
> >> +     priv->gpio_id_det = of_get_named_gpio(np, "hisilicon,gpio_id_det", 0);
> >> +     if (priv->gpio_id_det == -EPROBE_DEFER)
> >> +             return -EPROBE_DEFER;
> >> +     if (!gpio_is_valid(priv->gpio_id_det)) {
> >> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_id_det);
> >> +             return -ENODEV;
> >> +     }
> >> +
> >> +     priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> >> +                                     "hisilicon,peripheral-syscon");
> >> +     if (IS_ERR(priv->reg))
> >> +             priv->reg = NULL;
> >
> > You may differentiate -ENODEV and other errors, for other errors, you
> > can show an error, and return directly.
> 
> Here I want to set this property as optional, in case other platform
> do not need this property.
> So phy_setup also add protection if (priv->reg == NULL) return;
> 

If syscon_regmap_lookup_by_phandle returns -EPROBE_DEFER, you may want
to try later.

Peter
> >
> >> +
> >> +     INIT_DELAYED_WORK(&priv->work, hi6220_detect_work);
> >> +
> >> +     ret = devm_gpio_request_one(&pdev->dev, priv->gpio_vbus_det,
> >> +                                 GPIOF_IN, "gpio_vbus_det");
> >> +     if (ret < 0) {
> >> +             dev_err(&pdev->dev, "gpio request failed for gpio_vbus_det\n");
> >> +             return ret;
> >> +     }
> >> +
> >> +     ret = devm_gpio_request_one(&pdev->dev, priv->gpio_id_det,
> >> +                                 GPIOF_IN, "gpio_id_det");
> >> +     if (ret < 0) {
> >> +             dev_err(&pdev->dev, "gpio request failed for gpio_id_det\n");
> >> +             return ret;
> >> +     }
> >> +
> >> +     priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
> >> +     if (!IS_ERR(priv->vcc)) {
> >> +             ret = regulator_enable(priv->vcc);
> >> +             if (ret) {
> >> +                     dev_err(&pdev->dev, "Failed to enable regulator\n");
> >> +                     return -ENODEV;
> >> +             }
> >> +     }
> >> +
> >> +     priv->clk = devm_clk_get(&pdev->dev, NULL);
> >> +     if (IS_ERR(priv->clk)) {
> >> +             regulator_disable(priv->vcc);
> >> +             return PTR_ERR(priv->clk);
> >> +     }
> >> +     clk_prepare_enable(priv->clk);
> >> +
> >> +     irq = gpio_to_irq(priv->gpio_vbus_det);
> >> +     ret = devm_request_irq(&pdev->dev, gpio_to_irq(priv->gpio_vbus_det),
> >> +                            hiusb_gpio_intr, IRQF_NO_SUSPEND |
> >> +                            IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
> >> +                            "vbus_gpio_intr", priv);
> >> +     if (ret) {
> >> +             dev_err(&pdev->dev, "request gpio irq failed.\n");
> >> +             goto err_irq;
> >> +     }
> >
Zhangfei Gao Feb. 9, 2015, 3:31 a.m. UTC | #4 
On 9 February 2015 at 09:57, Peter Chen <peter.chen@freescale.com> wrote:
>> >> +static int hi6220_phy_probe(struct platform_device *pdev)
>> >> +{
>> >> +     struct hi6220_priv *priv;
>> >> +     struct usb_otg *otg;
>> >> +     struct device_node *np = pdev->dev.of_node;
>> >> +     int ret, irq;
>> >> +
>> >> +     priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>> >> +     if (!priv)
>> >> +             return -ENOMEM;
>> >> +
>> >> +     otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
>> >> +     if (!otg)
>> >> +             return -ENOMEM;
>> >> +
>> >> +     priv->phy.dev = &pdev->dev;
>> >> +     priv->phy.otg = otg;
>> >> +     priv->phy.label = "hi6220";
>> >> +     platform_set_drvdata(pdev, priv);
>> >> +     otg->set_peripheral = mv_otg_set_peripheral;
>> >> +
>> >> +     priv->gpio_vbus_det = of_get_named_gpio(np, "hisilicon,gpio_vbus_det", 0);
>> >> +     if (priv->gpio_vbus_det == -EPROBE_DEFER)
>> >> +             return -EPROBE_DEFER;
>> >> +     if (!gpio_is_valid(priv->gpio_vbus_det)) {
>> >> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_vbus_det);
>> >> +             return -ENODEV;
>> >> +     }
>> >> +
>> >> +     priv->gpio_id_det = of_get_named_gpio(np, "hisilicon,gpio_id_det", 0);
>> >> +     if (priv->gpio_id_det == -EPROBE_DEFER)
>> >> +             return -EPROBE_DEFER;
>> >> +     if (!gpio_is_valid(priv->gpio_id_det)) {
>> >> +             dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_id_det);
>> >> +             return -ENODEV;
>> >> +     }
>> >> +
>> >> +     priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
>> >> +                                     "hisilicon,peripheral-syscon");
>> >> +     if (IS_ERR(priv->reg))
>> >> +             priv->reg = NULL;
>> >
>> > You may differentiate -ENODEV and other errors, for other errors, you
>> > can show an error, and return directly.
>>
>> Here I want to set this property as optional, in case other platform
>> do not need this property.
>> So phy_setup also add protection if (priv->reg == NULL) return;
>>
>
> If syscon_regmap_lookup_by_phandle returns -EPROBE_DEFER, you may want
> to try later.
>
It should not.
syscon is postcore_initcall(syscon_init);

Thanks
diff mbox

Patch

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index c6d0c8e..405a3d0 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -173,6 +173,15 @@  config USB_MXS_PHY
 
 	  MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 
+config USB_HI6220_PHY
+	tristate "hi6220 USB PHY support"
+	select USB_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the HISILICON HI6220 USB PHY.
+
+	  To compile this driver as a module, choose M here.
+
 config USB_RCAR_PHY
 	tristate "Renesas R-Car USB PHY support"
 	depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 75f2bba..819283c 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -18,6 +18,7 @@  obj-$(CONFIG_SAMSUNG_USBPHY)		+= phy-samsung-usb.o
 obj-$(CONFIG_TWL6030_USB)		+= phy-twl6030-usb.o
 obj-$(CONFIG_USB_EHCI_TEGRA)		+= phy-tegra-usb.o
 obj-$(CONFIG_USB_GPIO_VBUS)		+= phy-gpio-vbus-usb.o
+obj-$(CONFIG_USB_HI6220_PHY)		+= phy-hi6220.o
 obj-$(CONFIG_USB_ISP1301)		+= phy-isp1301.o
 obj-$(CONFIG_USB_MSM_OTG)		+= phy-msm-usb.o
 obj-$(CONFIG_USB_MV_OTG)		+= phy-mv-usb.o
diff --git a/drivers/usb/phy/phy-hi6220.c b/drivers/usb/phy/phy-hi6220.c
new file mode 100644
index 0000000..87b1f0e
--- /dev/null
+++ b/drivers/usb/phy/phy-hi6220.c
@@ -0,0 +1,290 @@ 
+/*
+ * Copyright (c) 2015 Linaro Ltd.
+ * Copyright (c) 2015 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
+
+#define SC_PERIPH_CTRL4			0x00c
+
+#define PERIPH_CTRL4_PICO_SIDDQ		BIT(6)
+#define PERIPH_CTRL4_PICO_OGDISABLE	BIT(8)
+#define PERIPH_CTRL4_PICO_VBUSVLDEXT	BIT(10)
+#define PERIPH_CTRL4_PICO_VBUSVLDEXTSEL	BIT(11)
+#define PERIPH_CTRL4_OTG_PHY_SEL	BIT(21)
+
+#define SC_PERIPH_CTRL5			0x010
+
+#define PERIPH_CTRL5_USBOTG_RES_SEL	BIT(3)
+#define PERIPH_CTRL5_PICOPHY_ACAENB	BIT(4)
+#define PERIPH_CTRL5_PICOPHY_BC_MODE	BIT(5)
+#define PERIPH_CTRL5_PICOPHY_CHRGSEL	BIT(6)
+#define PERIPH_CTRL5_PICOPHY_VDATSRCEND	BIT(7)
+#define PERIPH_CTRL5_PICOPHY_VDATDETENB	BIT(8)
+#define PERIPH_CTRL5_PICOPHY_DCDENB	BIT(9)
+#define PERIPH_CTRL5_PICOPHY_IDDIG	BIT(10)
+
+#define SC_PERIPH_CTRL8			0x018
+
+#define EYE_PATTERN_PARA		0x7053348c
+
+#define SC_PERIPH_RSTDIS0		0x304
+
+#define PERIPH_RSTDIS0_USBOTG_BUS	BIT(4)
+#define PERIPH_RSTDIS0_POR_PICOPHY	BIT(5)
+#define PERIPH_RSTDIS0_USBOTG		BIT(6)
+#define PERIPH_RSTDIS0_USBOTG_32K	BIT(7)
+
+enum usb_mode {
+	USB_EMPTY,
+	GADGET_DEVICE,
+	OTG_HOST,
+};
+
+struct hi6220_priv {
+	struct usb_phy phy;
+	struct delayed_work work;
+	struct regmap *reg;
+	struct clk *clk;
+	struct regulator *vcc;
+	int gpio_vbus_det;
+	int gpio_id_det;
+	enum usb_mode mode;
+};
+
+static void hi6220_start_periphrals(struct hi6220_priv *priv, bool on)
+{
+	struct usb_otg *otg = priv->phy.otg;
+
+	if (!otg->gadget)
+		return;
+
+	if (on)
+		usb_gadget_connect(otg->gadget);
+	else
+		usb_gadget_disconnect(otg->gadget);
+}
+
+static void hi6220_detect_work(struct work_struct *work)
+{
+	struct hi6220_priv *priv =
+		container_of(work, struct hi6220_priv, work.work);
+	int id_det, vbus_det;
+	enum usb_mode mode;
+
+	if (!gpio_is_valid(priv->gpio_id_det) ||
+	    !gpio_is_valid(priv->gpio_vbus_det))
+		return;
+
+	id_det = gpio_get_value_cansleep(priv->gpio_id_det);
+	vbus_det = gpio_get_value_cansleep(priv->gpio_vbus_det);
+
+	if (vbus_det == 0) {
+		if (id_det == 1)
+			mode = GADGET_DEVICE;
+		else
+			mode = OTG_HOST;
+	} else {
+		mode = USB_EMPTY;
+	}
+
+	if (mode == GADGET_DEVICE && priv->mode == USB_EMPTY)
+		hi6220_start_periphrals(priv, true);
+	if (mode == USB_EMPTY && priv->mode == GADGET_DEVICE)
+		hi6220_start_periphrals(priv, false);
+
+	priv->mode = mode;
+}
+
+static irqreturn_t hiusb_gpio_intr(int irq, void *data)
+{
+	struct hi6220_priv *priv = (struct hi6220_priv *)data;
+
+	/* add debounce time */
+	schedule_delayed_work(&priv->work, msecs_to_jiffies(100));
+	return IRQ_HANDLED;
+}
+
+static int mv_otg_set_peripheral(struct usb_otg *otg,
+				 struct usb_gadget *gadget)
+{
+	struct hi6220_priv *priv;
+
+	priv = container_of(otg->usb_phy, struct hi6220_priv, phy);
+	otg->gadget = gadget;
+	return 0;
+}
+
+static void hi6220_phy_setup(struct hi6220_priv *priv)
+{
+	u32 val, mask;
+	int ret;
+
+	if (priv->reg == NULL)
+		return;
+
+	val = PERIPH_RSTDIS0_USBOTG_BUS | PERIPH_RSTDIS0_POR_PICOPHY |
+	      PERIPH_RSTDIS0_USBOTG | PERIPH_RSTDIS0_USBOTG_32K;
+	mask = val;
+	ret = regmap_update_bits(priv->reg, SC_PERIPH_RSTDIS0, mask, val);
+	if (ret)
+		return;
+
+	ret = regmap_read(priv->reg, SC_PERIPH_CTRL5, &val);
+	val = PERIPH_CTRL5_USBOTG_RES_SEL | PERIPH_CTRL5_PICOPHY_ACAENB;
+	mask = val | PERIPH_CTRL5_PICOPHY_BC_MODE;
+	ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL5, mask, val);
+	if (ret)
+		return;
+
+	val =  PERIPH_CTRL4_PICO_VBUSVLDEXT | PERIPH_CTRL4_PICO_VBUSVLDEXTSEL |
+	       PERIPH_CTRL4_OTG_PHY_SEL;
+	mask = val | PERIPH_CTRL4_PICO_SIDDQ | PERIPH_CTRL4_PICO_OGDISABLE;
+	ret = regmap_update_bits(priv->reg, SC_PERIPH_CTRL4, mask, val);
+	if (ret)
+		return;
+
+	ret = regmap_write(priv->reg, SC_PERIPH_CTRL8, EYE_PATTERN_PARA);
+	if (ret)
+		return;
+}
+
+static int hi6220_phy_probe(struct platform_device *pdev)
+{
+	struct hi6220_priv *priv;
+	struct usb_otg *otg;
+	struct device_node *np = pdev->dev.of_node;
+	int ret, irq;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg)
+		return -ENOMEM;
+
+	priv->phy.dev = &pdev->dev;
+	priv->phy.otg = otg;
+	priv->phy.label = "hi6220";
+	platform_set_drvdata(pdev, priv);
+	otg->set_peripheral = mv_otg_set_peripheral;
+
+	priv->gpio_vbus_det = of_get_named_gpio(np, "hisilicon,gpio_vbus_det", 0);
+	if (priv->gpio_vbus_det == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+	if (!gpio_is_valid(priv->gpio_vbus_det)) {
+		dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_vbus_det);
+		return -ENODEV;
+	}
+
+	priv->gpio_id_det = of_get_named_gpio(np, "hisilicon,gpio_id_det", 0);
+	if (priv->gpio_id_det == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+	if (!gpio_is_valid(priv->gpio_id_det)) {
+		dev_err(&pdev->dev, "invalid gpio %d\n", priv->gpio_id_det);
+		return -ENODEV;
+	}
+
+	priv->reg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+					"hisilicon,peripheral-syscon");
+	if (IS_ERR(priv->reg))
+		priv->reg = NULL;
+
+	INIT_DELAYED_WORK(&priv->work, hi6220_detect_work);
+
+	ret = devm_gpio_request_one(&pdev->dev, priv->gpio_vbus_det,
+				    GPIOF_IN, "gpio_vbus_det");
+	if (ret < 0) {
+		dev_err(&pdev->dev, "gpio request failed for gpio_vbus_det\n");
+		return ret;
+	}
+
+	ret = devm_gpio_request_one(&pdev->dev, priv->gpio_id_det,
+				    GPIOF_IN, "gpio_id_det");
+	if (ret < 0) {
+		dev_err(&pdev->dev, "gpio request failed for gpio_id_det\n");
+		return ret;
+	}
+
+	priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
+	if (!IS_ERR(priv->vcc)) {
+		ret = regulator_enable(priv->vcc);
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to enable regulator\n");
+			return -ENODEV;
+		}
+	}
+
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		regulator_disable(priv->vcc);
+		return PTR_ERR(priv->clk);
+	}
+	clk_prepare_enable(priv->clk);
+
+	irq = gpio_to_irq(priv->gpio_vbus_det);
+	ret = devm_request_irq(&pdev->dev, gpio_to_irq(priv->gpio_vbus_det),
+			       hiusb_gpio_intr, IRQF_NO_SUSPEND |
+			       IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+			       "vbus_gpio_intr", priv);
+	if (ret) {
+		dev_err(&pdev->dev, "request gpio irq failed.\n");
+		goto err_irq;
+	}
+
+	hi6220_phy_setup(priv);
+	ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't register transceiver\n");
+		goto err_irq;
+	}
+	schedule_delayed_work(&priv->work, 0);
+
+	return 0;
+err_irq:
+	clk_disable_unprepare(priv->clk);
+	regulator_disable(priv->vcc);
+	return ret;
+}
+
+static int hi6220_phy_remove(struct platform_device *pdev)
+{
+	struct hi6220_priv *priv = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(priv->clk);
+	regulator_disable(priv->vcc);
+	return 0;
+}
+
+static const struct of_device_id hi6220_phy_of_match[] = {
+	{.compatible = "hisilicon,hi6220-usb-phy",},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, hi6220_phy_of_match);
+
+static struct platform_driver hi6220_phy_driver = {
+	.probe	= hi6220_phy_probe,
+	.remove	= hi6220_phy_remove,
+	.driver = {
+		.name	= "hi6220-usb-phy",
+		.of_match_table	= hi6220_phy_of_match,
+	}
+};
+module_platform_driver(hi6220_phy_driver);
+
+MODULE_DESCRIPTION("HISILICON HI6220 USB PHY driver");
+MODULE_ALIAS("platform:hi6220-usb-phy");
+MODULE_LICENSE("GPL");