@@ -545,12 +545,13 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
armada-xp-netgear-rn2120.dtb \
armada-xp-openblocks-ax3-4.dtb \
armada-xp-synology-ds414.dtb
-dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
+dtb-$(CONFIG_MACH_DOVE) += \
dove-cubox.dtb \
dove-cubox-es.dtb \
dove-d2plug.dtb \
dove-d3plug.dtb \
- dove-dove-db.dtb
+ dove-dove-db.dtb \
+ dove-sbc-a510.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6589-aquaris5.dtb \
mt6592-evb.dtb \
mt8127-moose.dtb \
deleted file mode 100644
@@ -1,38 +0,0 @@
-/dts-v1/;
-
-#include "dove.dtsi"
-
-/ {
- model = "Compulab CM-A510";
- compatible = "compulab,cm-a510", "marvell,dove";
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x40000000>;
- };
-
- chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk";
- };
-};
-
-&uart0 { status = "okay"; };
-&uart1 { status = "okay"; };
-&sdio0 { status = "okay"; };
-&sdio1 { status = "okay"; };
-&sata0 { status = "okay"; };
-
-&spi0 {
- status = "okay";
-
- /* spi0.0: 4M Flash Winbond W25Q32BV */
- spi-flash@0 {
- compatible = "st,w25q32";
- spi-max-frequency = <20000000>;
- reg = <0>;
- };
-};
-
-&i2c0 {
- status = "okay";
-};
new file mode 100644
@@ -0,0 +1,195 @@
+/*
+ * Device Tree include for Compulab CM-A510 System-on-Module
+ *
+ * Copyright (C) 2015, Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * The CM-A510 comes with several optional components:
+ *
+ * Memory options:
+ * D512: 512M
+ * D1024: 1G
+ *
+ * NAND options:
+ * N512: 512M NAND
+ *
+ * Ethernet options:
+ * E1: PHY RTL8211D on internal GbE (SMI address 0x03)
+ * E2: Additional ethernet NIC RTL8111D on PCIe1
+ *
+ * Audio options:
+ * A: TI TLV320AIC23b audio codec (I2C address 0x1a)
+ *
+ * Touchscreen options:
+ * I: TI TSC2046 touchscreen controller (on SPI1)
+ *
+ * USB options:
+ * U2: 2 dual-role USB2.0 ports
+ * U4: 2 additional USB2.0 host ports (via USB1)
+ *
+ * WiFi options:
+ * W: Broadcom BCM4319 802.11b/g/n (USI WM-N-BM-01 on SDIO1)
+ *
+ * GPIOs used on CM-A510:
+ * 1 GbE PHY reset (active low)
+ * 3 WakeUp
+ * 8 PowerOff (active low)
+ * 13 Touchscreen pen irq (active low)
+ * 65 System LED (active high)
+ * 69 USB Hub reset (active low)
+ * 70 WLAN reset (active low)
+ * 71 WLAN regulator (active high)
+ */
+
+#include "dove.dtsi"
+
+/ {
+ model = "Compulab CM-A510";
+ compatible = "compulab,cm-a510", "marvell,dove";
+
+ /*
+ * Set the minimum memory size here and let the
+ * bootloader set the real size.
+ */
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ /* Set upper NAND data bit to GPO */
+ pinctrl-0 = <&pmx_nand_gpo>;
+ pinctrl-names = "default";
+
+ system {
+ label = "cm-a510:system:green";
+ gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi_power: regulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "WiFi Power";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+/* Optional RTL8211D GbE PHY on SMI address 0x03 */
+ðphy {
+ reg = <3>;
+ status = "disabled";
+};
+
+&i2c0 {
+ /* Optional TI TLV320AIC23b audio codec */
+ opt_audio: audio@1a {
+ compatible = "ti,tlv320aic23";
+ reg = <0x1a>;
+ status = "disabled";
+ };
+};
+
+/* Optional RTL8111D GbE NIC on PCIe1 */
+&pcie { status = "disabled"; };
+
+&pcie1 {
+ pinctrl-0 = <&pmx_pcie1_clkreq>;
+ pinctrl-names = "default";
+ status = "disabled";
+};
+
+&pinctrl {
+ pmx_uart2: pmx-uart2 {
+ marvell,pins = "mpp14", "mpp15";
+ marvell,function = "uart2";
+ };
+};
+
+/* Optional Broadcom BCM4319 802.11b/g/n WiFi module */
+&sdio1 {
+ non-removable;
+ vmmc-supply = <&wifi_power>;
+ reset-gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+};
+
+&spi0 {
+ status = "okay";
+
+ /* 1M Flash Winbond W25Q80BL */
+ flash@0 {
+ compatible = "winbond,w25q80";
+ spi-max-frequency = <80000000>;
+ reg = <0>;
+ };
+};
+
+&spi1 {
+ pinctrl-0 = <&pmx_spi1_20_23>;
+ pinctrl-names = "default";
+ status = "disabled";
+
+ /* Optional TI TSC2046 touchscreen controller */
+ opt_touch: touchscreen@0 {
+ compatible = "ti,tsc2046";
+ spi-max-frequency = <2500000>;
+ reg = <0>;
+ pinctrl-0 = <&pmx_gpio_13>;
+ pinctrl-names = "default";
+ interrupts-extended = <&gpio0 13 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&uart2 {
+ pinctrl-0 = <&pmx_uart2>;
+ pinctrl-names = "default";
+};
new file mode 100644
@@ -0,0 +1,182 @@
+/*
+ * Device Tree file for Compulab SBC-A510 Single Board Computer
+ *
+ * Copyright (C) 2015, Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * SBC-A510 comprises a PCA9555 I2C GPIO expander its GPIO lines connected to
+ *
+ * 0.0 USB0 VBUS_EN (active high)
+ * 0.1 USB0 VBUS_GOOD
+ * 0.2 DVI transmitter TI TFP410 MSEN
+ * 0.3 DVI transmitter TI TFP410 PD# (active low power down)
+ * 0.4 LVDS transmitter DS90C365 PD# (active low power down)
+ * 0.5 LCD nRST (active low reset)
+ * 0.6 PCIe0 nRST (active low reset)
+ * 0.7 mini-PCIe slot W_DISABLE#
+ *
+ * 1.0 MMC WP
+ * 1.1 Camera Input FPC FLASH_STB and P21.5
+ * 1.2 Camera Input FPC WE and P21.22
+ * 1.3 MMC VCC_EN (active high) and P21.7
+ * 1.4 Camera Input FPC AFTR_RST and P21.17
+ * 1.5 Camera Input FPC OE and P21.19
+ * 1.6 Camera Input FPC SNPSHT and P21.6
+ * 1.7 Camera Input FPC SHTR and P21.10
+ */
+
+/dts-v1/;
+
+#include "dove-cm-a510.dtsi"
+
+/ {
+ model = "Compulab SBC-A510";
+ compatible = "compulab,sbc-a510", "compulab,cm-a510", "marvell,dove";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ regulators {
+ usb0_power: regulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ mmc_power: regulator@3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MMC Power";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+/* Ethernet0 depends on CM-A510 option E1 */
+&mdio { status = "disabled"; };
+ð { status = "disabled"; };
+ðphy { status = "disabled"; };
+
+/*
+ * USB port 0 can be powered and monitored by I2C GPIO expander:
+ * VBUS_ENABLE on GPIO0, VBUS_GOOD on GPIO1
+ */
+&ehci0 {
+ status = "okay";
+ vbus-supply = <&usb0_power>;
+};
+
+/* USB port 1 (and ports 2, 3 if CM-A510 has U4 option) */
+&ehci1 { status = "okay"; };
+
+/*
+ * I2C bus layout:
+ * i2c0:
+ * - Audio Codec, 0x1a (option from CM-A510)
+ * - DVI transmitter TI TFP410, 0x39
+ * - HDMI/DVI DDC channel
+ * i2c1:
+ * - GPIO expander, NXP PCA9555, 0x20
+ * - VGA DDC channel
+ */
+&i2c {
+ pinctrl-0 = <&pmx_i2c1>;
+ pinctrl-names = "default";
+};
+
+&i2c0 {
+ /* TI TFP410 DVI transmitter */
+ dvi: video@39 {
+ compatible = "ti,tfp410";
+ reg = <0x39>;
+ powerdown-gpio = <&gpio_ext 3 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ /* NXP PCA9555 GPIO expander */
+ gpio_ext: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ #gpio-cells = <2>;
+ };
+};
+
+&pcie { status = "okay"; };
+
+/*
+ * PCIe0 can be configured by Jumper E1 to be either connected to
+ * a mini-PCIe slot or a Pericom PI7C9X111 PCIe-to-PCI bridge.
+ */
+&pcie0 {
+ status = "okay";
+ pinctrl-0 = <&pmx_pcie0_clkreq>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio_ext 6 GPIO_ACTIVE_LOW>;
+};
+
+/* Ethernet1 depends on CM-A510 option E2 */
+&pcie1 { status = "disabled"; };
+
+/* SATA connector */
+&sata0 { status = "okay"; };
+
+/*
+ * SDIO0 is connected to a MMC/SD/SDIO socket, I2C GPIO expander has
+ * VCC_MMC_ENABLE on GPIO13, MMC_WP on GPIO10
+ */
+&sdio0 {
+ vmmc-supply = <&mmc_power>;
+ wp-gpios = <&gpio_ext 10 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+/* UART0 on RS232 mini-connector */
+&uart0 { status = "okay"; };
+/* UART2 on pin headers */
+&uart2 { status = "okay"; };