@@ -32,6 +32,9 @@
#include <asm/cputype.h>
#include <asm/smp_plat.h>
+extern int qcom_idle_enter(unsigned long index);
+extern int qcom_cpuidle_init(struct device_node *cpu_node, u32 cpu);
+
static DEFINE_RAW_SPINLOCK(boot_lock);
DEFINE_PER_CPU(int, cold_boot_done);
@@ -339,5 +342,7 @@ static const struct cpu_operations msm_cortex_a_ops = {
.cpu_prepare = msm_cpu_prepare,
.cpu_boot = msm_cpu_boot,
.cpu_postboot = msm_cpu_postboot,
+ .cpu_suspend = qcom_idle_enter,
+ .cpu_init_idle = qcom_cpuidle_init,
};
CPU_METHOD_OF_DECLARE(msm_cortex_a_ops, &msm_cortex_a_ops);
@@ -29,6 +29,7 @@
#include <asm/cpuidle.h>
#include <asm/proc-fns.h>
#include <asm/suspend.h>
+#include <asm/cpu_ops.h>
#define MAX_PMIC_DATA 2
#define MAX_SEQ_DATA 64
@@ -185,7 +186,11 @@ static int qcom_cpu_spc(int cpu)
struct spm_driver_data *drv = per_cpu(cpu_spm_drv, cpu);
spm_set_low_power_mode(drv, PM_SLEEP_MODE_SPC);
+#if defined (CONFIG_ARCH_ARM)
ret = cpu_suspend(0, qcom_pm_collapse);
+#else
+ ret = __cpu_suspend(0, qcom_pm_collapse);
+#endif
/*
* ARM common code executes WFI without calling into our driver and
* if the SPM mode is not reset, then we may accidently power down the
@@ -197,7 +202,7 @@ static int qcom_cpu_spc(int cpu)
return ret;
}
-static int qcom_idle_enter(unsigned long index)
+int qcom_idle_enter(unsigned long index)
{
int cpu = smp_processor_id();
return per_cpu(qcom_idle_ops, cpu)[index](cpu);
@@ -208,7 +213,7 @@ static const struct of_device_id qcom_idle_state_match[] __initconst = {
{ },
};
-static int __init qcom_cpuidle_init(struct device_node *cpu_node, u32 cpu)
+int __init qcom_cpuidle_init(struct device_node *cpu_node, u32 cpu)
{
const struct of_device_id *match_id;
struct device_node *state_node;
@@ -275,13 +280,14 @@ check_spm:
return per_cpu(cpu_spm_drv, cpu) ? 0 : -ENXIO;
}
+#if defined (CONFIG_ARCH_ARM)
static struct cpuidle_ops qcom_cpuidle_ops __initdata = {
.suspend = qcom_idle_enter,
.init = qcom_cpuidle_init,
};
-
CPUIDLE_METHOD_OF_DECLARE(qcom_idle_v1, "qcom,kpss-acc-v1", &qcom_cpuidle_ops);
CPUIDLE_METHOD_OF_DECLARE(qcom_idle_v2, "qcom,kpss-acc-v2", &qcom_cpuidle_ops);
+#endif
static struct spm_driver_data *spm_get_drv(struct platform_device *pdev,
int *spm_cpu)
The SAW power controller can be used with both ARM v7 and v8 cpus. The driver registers with the cpuidle framework as a provider of idle entry points for all idle states. Certain aspects of cpuidle callback registration are different been ARM and ARM64 variants. Use compile time definitions to use appropriate idle and registration functions. Signed-off-by: Lina Iyer <lina.iyer@linaro.org> --- drivers/soc/qcom/cpu_ops.c | 5 +++++ drivers/soc/qcom/spm.c | 12 +++++++++--- 2 files changed, 14 insertions(+), 3 deletions(-)