[v8,02/16] ARM: ARMv7-M: Enlarge vector table up to 256 entries

Commit Message

Maxime Coquelin May 9, 2015, 7:53 a.m. UTC

From Cortex-M reference manuals, the nvic supports up to 240 interrupts.
So the number of entries in vectors table is up to 256.

This patch adds a new config flag to specify the number of external interrupts.
Some ifdeferies are added in order to respect the natural alignment without
wasting too much space on smaller systems.

Acked-by: Uwe Kleine-König <[e-mail]>
Acked-by: Stefan Agner <[e-mail]>
Tested-by: Chanwoo Choi <[e-mail]>
Signed-off-by: Maxime Coquelin <[e-mail]>
---
 arch/arm/kernel/entry-v7m.S | 13 +++++++++----
 arch/arm/mm/Kconfig         | 15 +++++++++++++++
 2 files changed, 24 insertions(+), 4 deletions(-)

Patch

diff --git a/arch/arm/kernel/entry-v7m.S b/arch/arm/kernel/entry-v7m.S
index 8944f49..b6c8bb9 100644
--- a/arch/arm/kernel/entry-v7m.S
+++ b/arch/arm/kernel/entry-v7m.S
@@ -117,9 +117,14 @@  ENTRY(__switch_to)
 ENDPROC(__switch_to)
 
 	.data
-	.align	8
+#if CONFIG_CPU_V7M_NUM_IRQ <= 112
+	.align	9
+#else
+	.align	10
+#endif
+
 /*
- * Vector table (64 words => 256 bytes natural alignment)
+ * Vector table (Natural alignment need to be ensured)
  */
 ENTRY(vector_table)
 	.long	0			@ 0 - Reset stack pointer
@@ -138,6 +143,6 @@  ENTRY(vector_table)
 	.long	__invalid_entry		@ 13 - Reserved
 	.long	__pendsv_entry		@ 14 - PendSV
 	.long	__invalid_entry		@ 15 - SysTick
-	.rept	64 - 16
-	.long	__irq_entry		@ 16..64 - External Interrupts
+	.rept	CONFIG_CPU_V7M_NUM_IRQ
+	.long	__irq_entry		@ External Interrupts
 	.endr
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index b4f92b9..6173aa3 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -604,6 +604,21 @@  config CPU_USE_DOMAINS
 	  This option enables or disables the use of domain switching
 	  via the set_fs() function.
 
+config CPU_V7M_NUM_IRQ
+	int "Number of external interrupts connected to the NVIC"
+	depends on CPU_V7M
+	default 90 if ARCH_STM32
+	default 38 if ARCH_EFM32
+	default 240
+	help
+	  This option indicates the number of interrupts connected to the NVIC.
+	  The value can be larger than the real number of interrupts supported
+	  by the system, but must not be lower.
+	  The default value is 240, corresponding to the maximum number of
+	  interrupts supported by the NVIC on Cortex-M family.
+
+	  If unsure, keep default value.
+
 #
 # CPU supports 36-bit I/O
 #