new file mode 100644
@@ -0,0 +1,77 @@
+* NXP LPC1850 Clock Control Unit (CCU)
+
+Each CGU base clock has several clock branches which can be turned on
+or off independently by the Clock Control Units CCU1 or CCU2. The
+branch clocks are distributed between CCU1 and CCU2.
+
+ - Above text taken from NXP LPC1850 User Manual.
+
+This binding uses the common clock binding:
+ Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible:
+ Should be "nxp,lpc1850-ccu"
+- reg:
+ Shall define the base and range of the address space
+ containing clock control registers
+- #clock-cells:
+ Shall have value <1>. The permitted clock-specifier values
+ are the branch clock names defined in table below.
+- clocks:
+ Shall contain a list of phandles for the base clocks routed
+ from the CGU to the specific CCU. See mapping of base clocks
+ and CCU in table below.
+- clock-names:
+ Shall contain a list of names for the base clock routed
+ from the CGU to the specific CCU. Valid CCU clock names:
+ "base_usb0_clk", "base_periph_clk", "base_usb1_clk",
+ "base_cpu_clk", "base_spifi_clk", "base_spi_clk",
+ "base_apb1_clk", "base_apb3_clk", "base_adchs_clk",
+ "base_sdio_clk", "base_ssp0_clk", "base_ssp1_clk",
+ "base_uart0_clk", "base_uart1_clk", "base_uart2_clk",
+ "base_uart3_clk", "base_audio_clk"
+
+Which branch clocks that are available on the CCU depends on the
+specific LPC part. Check the user manual for your specific part.
+
+A list of CCU clocks can be found in dt-bindings/clock/lpc18xx-ccu.h.
+
+Example board file:
+
+soc {
+ ccu1: clock-controller@40051000 {
+ compatible = "nxp,lpc1850-ccu";
+ reg = <0x40051000 0x1000>;
+ #clock-cells = <1>;
+ clocks = <&cgu BASE_APB3_CLK>, <&cgu BASE_APB1_CLK>,
+ <&cgu BASE_SPIFI_CLK>, <&cgu BASE_CPU_CLK>,
+ <&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>,
+ <&cgu BASE_USB1_CLK>, <&cgu BASE_SPI_CLK>;
+ clock-names = "base_apb3_clk", "base_apb1_clk",
+ "base_spifi_clk", "base_cpu_clk",
+ "base_periph_clk", "base_usb0_clk",
+ "base_usb1_clk", "base_spi_clk";
+ };
+
+ ccu2: clock-controller@40052000 {
+ compatible = "nxp,lpc1850-ccu";
+ reg = <0x40052000 0x1000>;
+ #clock-cells = <1>;
+ clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>,
+ <&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>,
+ <&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>,
+ <&cgu BASE_SSP0_CLK>, <&cgu BASE_SDIO_CLK>;
+ clock-names = "base_audio_clk", "base_uart3_clk",
+ "base_uart2_clk", "base_uart1_clk",
+ "base_uart0_clk", "base_ssp1_clk",
+ "base_ssp0_clk", "base_sdio_clk";
+ };
+
+ /* A user of CCU brach clocks */
+ uart1: serial@40082000 {
+ ...
+ clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>;
+ ...
+ };
+};
Add DT binding documentation for lpc1850-ccu clk driver. Signed-off-by: Joachim Eastwood <manabian@gmail.com> --- .../devicetree/bindings/clock/lpc1850-ccu.txt | 77 ++++++++++++++++++++++ 1 file changed, 77 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/lpc1850-ccu.txt