| Message ID | 1432912764-7073-5-git-send-email-alex.bennee@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 29 May 2015 at 16:19, Alex Bennée <alex.bennee@linaro.org> wrote: > This adds support for single-step. There isn't much to do on the QEMU > side as after we set-up the request for single step via the debug ioctl > it is all handled within the kernel. > > Signed-off-by: Alex Bennée <alex.bennee@linaro.org> > > --- > v2 > - convert to using HSR_EC > v3 > - use internals.h definitions > --- > target-arm/kvm.c | 10 ++++++++++ > 1 file changed, 10 insertions(+) > > diff --git a/target-arm/kvm.c b/target-arm/kvm.c > index c3bad6f..de2865a 100644 > --- a/target-arm/kvm.c > +++ b/target-arm/kvm.c > @@ -528,6 +528,13 @@ static int kvm_handle_debug(CPUState *cs, struct kvm_run *run) > kvm_cpu_synchronize_state(cs); > > switch (hsr_ec) { > + case EC_SOFTWARESTEP: > + if (cs->singlestep_enabled) { > + return true; > + } else { > + error_report("Came out of SINGLE STEP when not enabled"); All-caps there is a bit odd. > + } > + break; > case EC_AA64_BKPT: > if (kvm_find_sw_breakpoint(cs, env->pc)) { > return true; > @@ -588,6 +595,9 @@ int kvm_arch_on_sigbus(int code, void *addr) > > void kvm_arch_update_guest_debug(CPUState *cs, struct kvm_guest_debug *dbg) > { > + if (cs->singlestep_enabled) { > + dbg->control |= KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_SINGLESTEP; > + } > if (kvm_sw_breakpoints_active(cs)) { > dbg->control |= KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_USE_SW_BP; > } Again, is there a guard somewhere to prevent us trying to enable singlestep if the kernel doesn't support it? -- PMM
diff --git a/target-arm/kvm.c b/target-arm/kvm.c index c3bad6f..de2865a 100644 --- a/target-arm/kvm.c +++ b/target-arm/kvm.c @@ -528,6 +528,13 @@ static int kvm_handle_debug(CPUState *cs, struct kvm_run *run) kvm_cpu_synchronize_state(cs); switch (hsr_ec) { + case EC_SOFTWARESTEP: + if (cs->singlestep_enabled) { + return true; + } else { + error_report("Came out of SINGLE STEP when not enabled"); + } + break; case EC_AA64_BKPT: if (kvm_find_sw_breakpoint(cs, env->pc)) { return true; @@ -588,6 +595,9 @@ int kvm_arch_on_sigbus(int code, void *addr) void kvm_arch_update_guest_debug(CPUState *cs, struct kvm_guest_debug *dbg) { + if (cs->singlestep_enabled) { + dbg->control |= KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_SINGLESTEP; + } if (kvm_sw_breakpoints_active(cs)) { dbg->control |= KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_USE_SW_BP; }
This adds support for single-step. There isn't much to do on the QEMU side as after we set-up the request for single step via the debug ioctl it is all handled within the kernel. Signed-off-by: Alex Bennée <alex.bennee@linaro.org> --- v2 - convert to using HSR_EC v3 - use internals.h definitions --- target-arm/kvm.c | 10 ++++++++++ 1 file changed, 10 insertions(+)