@@ -48,7 +48,6 @@ endchoice
config SA1100_COLLIE
bool "Sharp Zaurus SL5500"
# FIXME: select ARM_SA11x0_CPUFREQ
- select SHARP_LOCOMO
select SHARP_PARAM
select SHARP_SCOOP
help
@@ -24,13 +24,21 @@
#include <linux/platform_data/sa11x0-serial.h>
#include <linux/platform_device.h>
#include <linux/mfd/ucb1x00.h>
+#include <linux/mfd/locomo.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/timer.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
+#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/power/gpio-charger.h>
+#include <linux/gpio/machine.h>
+#include <linux/iio/machine.h>
+#include <linux/mmc/host.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/spi/mmc_spi.h>
#include <video/sa1100fb.h>
@@ -47,7 +55,6 @@
#include <asm/hardware/scoop.h>
#include <asm/mach/sharpsl_param.h>
-#include <asm/hardware/locomo.h>
#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
@@ -151,36 +158,54 @@ static struct platform_device collie_power_device = {
.dev.platform_data = &collie_power_data,
};
-#ifdef CONFIG_SHARP_LOCOMO
/*
* low-level UART features.
*/
-struct platform_device collie_locomo_device;
+static struct gpio collie_uart_gpio[] = {
+ { COLLIE_GPIO_CTS, GPIOF_IN, "CTS" },
+ { COLLIE_GPIO_RTS, GPIOF_OUT_INIT_LOW, "RTS" },
+ { COLLIE_GPIO_DTR, GPIOF_OUT_INIT_LOW, "DTR" },
+ { COLLIE_GPIO_DSR, GPIOF_IN, "DSR" },
+};
+
+static bool collie_uart_gpio_ok;
static void collie_uart_set_mctrl(struct uart_port *port, u_int mctrl)
{
- if (mctrl & TIOCM_RTS)
- locomo_gpio_write(&collie_locomo_device.dev, LOCOMO_GPIO_RTS, 0);
- else
- locomo_gpio_write(&collie_locomo_device.dev, LOCOMO_GPIO_RTS, 1);
-
- if (mctrl & TIOCM_DTR)
- locomo_gpio_write(&collie_locomo_device.dev, LOCOMO_GPIO_DTR, 0);
- else
- locomo_gpio_write(&collie_locomo_device.dev, LOCOMO_GPIO_DTR, 1);
+ if (!collie_uart_gpio_ok) {
+ int rc = gpio_request_array(collie_uart_gpio,
+ ARRAY_SIZE(collie_uart_gpio));
+ if (rc)
+ pr_err("collie_uart_set_mctrl: gpio request %d\n", rc);
+ else
+ collie_uart_gpio_ok = true;
+ }
+
+ if (collie_uart_gpio_ok) {
+ gpio_set_value(COLLIE_GPIO_RTS, !(mctrl & TIOCM_RTS));
+ gpio_set_value(COLLIE_GPIO_DTR, !(mctrl & TIOCM_DTR));
+ }
}
static u_int collie_uart_get_mctrl(struct uart_port *port)
{
int ret = TIOCM_CD;
- unsigned int r;
- r = locomo_gpio_read_output(&collie_locomo_device.dev, LOCOMO_GPIO_CTS & LOCOMO_GPIO_DSR);
- if (r == -ENODEV)
+ if (!collie_uart_gpio_ok) {
+ int rc = gpio_request_array(collie_uart_gpio,
+ ARRAY_SIZE(collie_uart_gpio));
+ if (rc)
+ pr_err("collie_uart_get_mctrl: gpio request %d\n", rc);
+ else
+ collie_uart_gpio_ok = true;
+ }
+
+ if (!collie_uart_gpio_ok)
return ret;
- if (r & LOCOMO_GPIO_CTS)
+
+ if (gpio_get_value(COLLIE_GPIO_CTS))
ret |= TIOCM_CTS;
- if (r & LOCOMO_GPIO_DSR)
+ if (gpio_get_value(COLLIE_GPIO_DSR))
ret |= TIOCM_DSR;
return ret;
@@ -191,33 +216,35 @@ static struct sa1100_port_fns collie_port_fns __initdata = {
.get_mctrl = collie_uart_get_mctrl,
};
-static int collie_uart_probe(struct locomo_dev *dev)
-{
- return 0;
-}
-
-static int collie_uart_remove(struct locomo_dev *dev)
-{
- return 0;
-}
+static struct regulator_consumer_supply collie_amp_on_consumer_supplies[] = {
+ REGULATOR_SUPPLY("VCC", "1-004e"),
+};
-static struct locomo_driver collie_uart_driver = {
- .drv = {
- .name = "collie_uart",
+static struct regulator_init_data collie_amp_on_init_data = {
+ .constraints = {
+ .name = "AMP_ON",
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
- .devid = LOCOMO_DEVID_UART,
- .probe = collie_uart_probe,
- .remove = collie_uart_remove,
+ .consumer_supplies = collie_amp_on_consumer_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(collie_amp_on_consumer_supplies),
};
-static int __init collie_uart_init(void)
-{
- return locomo_driver_register(&collie_uart_driver);
-}
-device_initcall(collie_uart_init);
-
-#endif
+static struct fixed_voltage_config collie_amp_on_data = {
+ .supply_name = "amp_on",
+ .microvolts = 3300000,
+ .gpio = COLLIE_GPIO_AMP2_ON,
+ .startup_delay = 5,
+ .enable_high = 1,
+ .init_data = &collie_amp_on_init_data,
+};
+static struct platform_device collie_amp_on_device = {
+ .name = "reg-fixed-voltage",
+ .id = -1,
+ .dev = {
+ .platform_data = &collie_amp_on_data,
+ },
+};
static struct resource locomo_resources[] = {
[0] = DEFINE_RES_MEM(0x40000000, SZ_8K),
@@ -225,14 +252,15 @@ static struct resource locomo_resources[] = {
};
static struct locomo_platform_data locomo_info = {
- .irq_base = IRQ_BOARD_START,
+ .gpio_base = COLLIE_LOCOMO_GPIO_BASE,
+ .comadj = 128,
};
-struct platform_device collie_locomo_device = {
+static struct platform_device collie_locomo_device = {
.name = "locomo",
.id = 0,
.dev = {
- .platform_data = &locomo_info,
+ .platform_data = &locomo_info,
},
.num_resources = ARRAY_SIZE(locomo_resources),
.resource = locomo_resources,
@@ -270,7 +298,55 @@ static struct platform_device collie_gpio_keys_device = {
},
};
+static int collie_mmc_init(struct device *dev,
+ irqreturn_t (*isr)(int, void*), void *mmc)
+{
+ int ret;
+
+ ret = gpio_request(COLLIE_GPIO_CARD_POWER, "MMC power");
+ if (!ret)
+ ret = gpio_direction_output(COLLIE_GPIO_CARD_POWER, 0);
+ if (ret)
+ gpio_free(COLLIE_GPIO_CARD_POWER);
+ return ret;
+}
+
+static void collie_mmc_exit(struct device *dev, void *mmc)
+{
+ gpio_free(COLLIE_GPIO_CARD_POWER);
+}
+
+static void collie_mmc_setpower(struct device *dev, unsigned int mask)
+{
+ gpio_set_value(COLLIE_GPIO_CARD_POWER, !!mask);
+}
+
+static struct mmc_spi_platform_data collie_mmc_data = {
+ .init = collie_mmc_init,
+ .exit = collie_mmc_exit,
+ .setpower = collie_mmc_setpower,
+ .detect_delay = 200,
+ .powerup_msecs = 200,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO,
+ .cd_gpio = COLLIE_GPIO_CARD_DETECT,
+ .ro_gpio = COLLIE_GPIO_CARD_RO,
+ .caps2 = MMC_CAP2_RO_ACTIVE_HIGH,
+};
+
+static struct spi_board_info collie_spi_board_info[] __initdata = {
+ {
+ .modalias = "mmc_spi",
+ .platform_data = &collie_mmc_data,
+ .max_speed_hz = 25000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ },
+};
+
static struct platform_device *devices[] __initdata = {
+ &collie_amp_on_device,
&collie_locomo_device,
&colliescoop_device,
&collie_power_device,
@@ -347,10 +423,39 @@ static struct sa1100fb_mach_info collie_lcd_info = {
.lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
.lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+};
-#ifdef CONFIG_BACKLIGHT_LOCOMO
- .lcd_power = locomolcd_power
-#endif
+static struct iio_map locomo_iio_map[] = {
+ {
+ .consumer_dev_name = "locomo-lcd.0",
+ .consumer_channel = "comadj",
+ .adc_channel_label = "CH0",
+ },
+ { }
+};
+
+static struct i2c_board_info locomo_i2c_devs[] __initdata = {
+ {
+ I2C_BOARD_INFO("m62332", 0x4e),
+ .platform_data = locomo_iio_map,
+ },
+};
+
+static struct gpiod_lookup_table collie_bl_gpios_table = {
+ .dev_id = "locomo-backlight.0",
+ .table = {
+ GPIO_LOOKUP("locomo-gpio", 9, "flvr", GPIO_ACTIVE_HIGH),
+ { },
+ },
+}, collie_lcd_gpios_table = {
+ .dev_id = "locomo-lcd.0",
+ .table = {
+ GPIO_LOOKUP("locomo-gpio", 4, "VSHA", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("locomo-gpio", 5, "VSHD", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("locomo-gpio", 6, "Vee", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("locomo-gpio", 7, "MOD", GPIO_ACTIVE_HIGH),
+ { },
+ },
};
static void __init collie_init(void)
@@ -381,11 +486,19 @@ static void __init collie_init(void)
GPSR |= _COLLIE_GPIO_UCB1x00_RESET;
+ sharpsl_save_param();
+
sa11x0_ppc_configure_mcp();
platform_scoop_config = &collie_pcmcia_config;
+ if (sharpsl_param.comadj != -1)
+ locomo_info.comadj = sharpsl_param.comadj;
+
+ gpiod_add_lookup_table(&collie_bl_gpios_table);
+ gpiod_add_lookup_table(&collie_lcd_gpios_table);
+
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
if (ret) {
printk(KERN_WARNING "collie: Unable to register LoCoMo device\n");
@@ -397,7 +510,13 @@ static void __init collie_init(void)
sa11x0_register_mcp(&collie_mcp_data);
sa11x0_register_irda(&collie_ir_data);
- sharpsl_save_param();
+ i2c_register_board_info(1,
+ locomo_i2c_devs, ARRAY_SIZE(locomo_i2c_devs));
+
+ spi_register_board_info(collie_spi_board_info,
+ ARRAY_SIZE(collie_spi_board_info));
+
+ regulator_has_full_constraints();
}
static struct map_desc collie_io_desc[] __initdata = {
@@ -419,9 +538,7 @@ static void __init collie_map_io(void)
sa1100_map_io();
iotable_init(collie_io_desc, ARRAY_SIZE(collie_io_desc));
-#ifdef CONFIG_SHARP_LOCOMO
sa1100_register_uart_fns(&collie_port_fns);
-#endif
sa1100_register_uart(0, 3);
sa1100_register_uart(1, 1);
}
@@ -24,12 +24,12 @@ extern void locomolcd_power(int on);
#define COLLIE_SCP_MUTE_L SCOOP_GPCR_PA14
#define COLLIE_SCP_MUTE_R SCOOP_GPCR_PA15
#define COLLIE_SCP_5VON SCOOP_GPCR_PA16
-#define COLLIE_SCP_AMP_ON SCOOP_GPCR_PA17
+#define COLLIE_GPIO_AMP2_ON (COLLIE_SCOOP_GPIO_BASE + 6)
#define COLLIE_GPIO_VPEN (COLLIE_SCOOP_GPIO_BASE + 7)
#define COLLIE_SCP_LB_VOL_CHG SCOOP_GPCR_PA19
#define COLLIE_SCOOP_IO_DIR (COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R | \
- COLLIE_SCP_5VON | COLLIE_SCP_AMP_ON | \
+ COLLIE_SCP_5VON | \
COLLIE_SCP_LB_VOL_CHG)
#define COLLIE_SCOOP_IO_OUT (COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R)
@@ -81,7 +81,7 @@ extern void locomolcd_power(int on);
#define COLLIE_TC35143_GPIO_TBL_CHK UCB_IO_1
#define COLLIE_TC35143_GPIO_VPEN_ON UCB_IO_2
#define COLLIE_GPIO_IR_ON (COLLIE_TC35143_GPIO_BASE + 3)
-#define COLLIE_TC35143_GPIO_AMP_ON UCB_IO_4
+#define COLLIE_GPIO_AMP1_ON (COLLIE_TC35143_GPIO_BASE + 4)
#define COLLIE_TC35143_GPIO_VERSION1 UCB_IO_5
#define COLLIE_TC35143_GPIO_FS8KLPF UCB_IO_5
#define COLLIE_TC35143_GPIO_BUZZER_BIAS UCB_IO_6
@@ -92,4 +92,14 @@ extern void locomolcd_power(int on);
#define COLLIE_TC35143_GPIO_OUT (UCB_IO_1 | UCB_IO_3 | UCB_IO_4 \
| UCB_IO_6)
+/* GPIOs on LoCoMo GA */
+#define COLLIE_LOCOMO_GPIO_BASE (GPIO_MAX + 13 + 10)
+#define COLLIE_GPIO_RTS (COLLIE_LOCOMO_GPIO_BASE + 0)
+#define COLLIE_GPIO_CTS (COLLIE_LOCOMO_GPIO_BASE + 1)
+#define COLLIE_GPIO_DSR (COLLIE_LOCOMO_GPIO_BASE + 2)
+#define COLLIE_GPIO_DTR (COLLIE_LOCOMO_GPIO_BASE + 3)
+#define COLLIE_GPIO_CARD_DETECT (COLLIE_LOCOMO_GPIO_BASE + 13)
+#define COLLIE_GPIO_CARD_RO (COLLIE_LOCOMO_GPIO_BASE + 14)
+#define COLLIE_GPIO_CARD_POWER (COLLIE_LOCOMO_GPIO_BASE + 15)
+
#endif
Switch collie to new mfd-based locomo driver. Update platform data and add necessary spi, i2c and regulator devices. Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> --- arch/arm/mach-sa1100/Kconfig | 1 - arch/arm/mach-sa1100/collie.c | 213 ++++++++++++++++++++++------- arch/arm/mach-sa1100/include/mach/collie.h | 16 ++- 3 files changed, 178 insertions(+), 52 deletions(-)