@@ -7,6 +7,7 @@ Optional properties:
- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
- regulator-min-microamp: smallest current consumers may set
- regulator-max-microamp: largest current consumers may set
+- regulator-input-current-limit-microamp: maximum input current regulator allows
- regulator-always-on: boolean, regulator should never be disabled
- regulator-boot-on: bootloader/firmware enabled regulator
- regulator-allow-bypass: allow the regulator to go into bypass mode
@@ -1008,6 +1008,15 @@ static int set_machine_constraints(struct regulator_dev *rdev,
if (ret != 0)
goto out;
+ if (rdev->constraints->ilim_uA && ops->set_input_current_limit) {
+ ret = ops->set_input_current_limit(rdev,
+ rdev->constraints->ilim_uA);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set input limit\n");
+ goto out;
+ }
+ }
+
/* do we need to setup our suspend state */
if (rdev->constraints->initial_state) {
ret = suspend_prepare(rdev, rdev->constraints->initial_state);
@@ -58,6 +58,10 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!of_property_read_u32(np, "regulator-max-microamp", &pval))
constraints->max_uA = pval;
+ if (!of_property_read_u32(np, "regulator-input-current-limit-microamp",
+ &pval))
+ constraints->ilim_uA = pval;
+
/* Current change possible? */
if (constraints->min_uA != constraints->max_uA)
constraints->valid_ops_mask |= REGULATOR_CHANGE_CURRENT;
@@ -91,6 +91,7 @@ struct regulator_linear_range {
* @set_current_limit: Configure a limit for a current-limited regulator.
* The driver should select the current closest to max_uA.
* @get_current_limit: Get the configured limit for a current-limited regulator.
+ * @set_input_current_limit: Configure an input limit.
*
* @set_mode: Set the configured operating mode for the regulator.
* @get_mode: Get the configured operating mode for the regulator.
@@ -145,6 +146,8 @@ struct regulator_ops {
int min_uA, int max_uA);
int (*get_current_limit) (struct regulator_dev *);
+ int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
+
/* enable/disable regulator */
int (*enable) (struct regulator_dev *);
int (*disable) (struct regulator_dev *);
@@ -75,6 +75,7 @@ struct regulator_state {
*
* @min_uA: Smallest current consumers may set.
* @max_uA: Largest current consumers may set.
+ * @ilim_uA: Maximum input current.
* @system_load: Load that isn't captured by any consumer requests.
*
* @valid_modes_mask: Mask of modes which may be configured by consumers.
@@ -113,6 +114,7 @@ struct regulation_constraints {
/* current output range (inclusive) - for current control */
int min_uA;
int max_uA;
+ int ilim_uA;
int system_load;
Some regulators can limit their input current (typically annotated as ilim). Add an op (set_input_current_limit) and a DT property + constraint to support this. Cc: <devicetree@vger.kernel.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> --- Documentation/devicetree/bindings/regulator/regulator.txt | 1 + drivers/regulator/core.c | 9 +++++++++ drivers/regulator/of_regulator.c | 4 ++++ include/linux/regulator/driver.h | 3 +++ include/linux/regulator/machine.h | 2 ++ 5 files changed, 19 insertions(+)