@@ -135,6 +135,9 @@ Boards:
- AM335X OrionLXm : Substation Automation Platform
compatible = "novatech,am335x-lxm", "ti,am33xx"
+- AM335X phyBOARD-WEGA: Single Board Computer dev kit
+ compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"
+
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"
@@ -438,7 +438,8 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-nano.dtb \
am335x-pepper.dtb \
am335x-lxm.dtb \
- am335x-chiliboard.dtb
+ am335x-chiliboard.dtb \
+ am335x-wega-rdk.dtb
dtb-$(CONFIG_ARCH_OMAP4) += \
omap4-duovero-parlor.dtb \
omap4-panda.dtb \
new file mode 100644
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2015 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-wega.dtsi"
+
+/* SoM */
+&i2c_eeprom {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,151 @@
+/*
+ * Copyright (C) 2015 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+ model = "Phytec AM335x phyBOARD-WEGA";
+ compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";
+
+};
+
+/* CAN Busses */
+&am33xx_pinmux {
+ dcan1_pins: pinmux_dcan1 {
+ pinctrl-single,pins = <
+ 0x168 (PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+ 0x16c (PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+ >;
+ };
+};
+
+&dcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins>;
+ status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+ ethernet1_pins: pinmux_ethernet1 {
+ pinctrl-single,pins = <
+ 0x40 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a0.mii2_txen */
+ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a1.mii2_rxdv */
+ 0x48 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a2.mii2_txd3 */
+ 0x4c (PIN_OUTPUT | MUX_MODE1) /* gpmc_a3.mii2_txd2 */
+ 0x50 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a4.mii2_txd1 */
+ 0x54 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a5.mii2_txd0 */
+ 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a6.mii2_txclk */
+ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a7.mii2_rxclk */
+ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a8.mii2_rxd3 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a9.mii2_rxd2 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a10.mii2_rxd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a11.mii2_rxd0 */
+ 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_wpn.mii2_rxerr */
+ 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_ben1.mii2_col */
+ >;
+ };
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "mii";
+ dual_emac_res_vlan = <2>;
+};
+
+&mac {
+ slaves = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet0_pins ðernet1_pins>;
+ dual_emac = <1>;
+};
+
+/* MMC */
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1 {
+ pinctrl-single,pins = <
+ 0x0F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+ 0x0F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+ 0x0F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+ 0x0FC (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+ 0x160 (PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */
+ >;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+/* UARTs */
+&am33xx_pinmux {
+ uart0_pins: pinmux_uart0 {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ 0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+/* USB */
+&cppi41dma {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
phyBOARD-WEGA-AM335x represents a direct soldered combination of a phyCORE-AM335x SoM and carrier board. Different kind of SoM options can be connected to the wega carrier board. So we created a separate wega dtsi file. The final dts contains the actual SoM on the carrier board. WEGA carrier board features: * ETH phy on carrier board: 1x MII * 1x CAN * 2x UART * USB0 (device) * USB1 (host) * mSD slot Signed-off-by: Teresa Remmet <t.remmet@phytec.de> --- .../devicetree/bindings/arm/omap/omap.txt | 3 + arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/am335x-wega-rdk.dts | 22 +++ arch/arm/boot/dts/am335x-wega.dtsi | 151 +++++++++++++++++++++ 4 files changed, 178 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am335x-wega-rdk.dts create mode 100644 arch/arm/boot/dts/am335x-wega.dtsi