| Message ID | 1438347836-29060-3-git-send-email-chunfeng.yun@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, Sorry for my late reply to a prior version of this series, but I still have concerns with some of the properties. I'll repeat those below. On Fri, Jul 31, 2015 at 02:03:53PM +0100, Chunfeng Yun wrote: > add a DT binding documentation of xHCI host controller for the > MT8173 SoC from Mediatek. > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > --- > .../devicetree/bindings/usb/mt8173-xhci.txt | 51 ++++++++++++++++++++++ > 1 file changed, 51 insertions(+) > create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt > > diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt > new file mode 100644 > index 0000000..364be5a > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt > @@ -0,0 +1,51 @@ > +MT65XX xhci > + > +The device node for Mediatek SOC usb3.0 host controller > + > +Required properties: > + - compatible : Supports "mediatek,mt8173-xhci" s/Supports/should contain/ > + - reg : Specifies physical base address and size of the registers, > + the first one for MAC, the second for IPPC > + - interrupts : Interrupt mode, number and trigger mode Just specify what this logically corresponds to; the format of the interrupts proeprty depends on the interrupt controller. > + - power-domains : To enable usb's mtcmos Please describe what this contains. I assume you exped a single power domain to be described, covering the whole xHCI controller? > + - vusb33-supply : Regulator of usb avdd3.3v > + - clocks : Must support all clocks that xhci needs - clocks: a list of phandle + clock-specifier pairs, one for each entry in clock-names. > + - clock-names : Should be "sys_mac" for sys and mac clocks, and > + "wakeup_deb_p0", "wakeup_deb_p1" for wakeup debounce control > + clocks This would be better as a list, e.g. - clock-names: should contain: * "sys_mac" <description here if necessary> * "wakeup_deb_p0" <description here if necessary> * "wakeup_deb_p1" <description here if necessary> Is sys_mac a single clock input line? Or is it jsut the case that a single line feeds two inputs currently? if the latter they should be separate entries. > + - phys : List of PHY specifiers (used by generic PHY framework). The bracketed part should go. The bidnigns should know nothing of Linux internals. > + - phy-names : Must be "usb-phy0", "usb-phy1",.., "usb-phyN", based on > + the number of PHYs as specified in @phys property. This is useless. You either don't need names, and can acquire the phys by index, or you need names which correspond to those on the data sheet for the xHCI controller. > + - mediatek,usb-wakeup : To access usb wakeup control register Please describe what this points to (I guess it's a syscon)/ > + - mediatek,wakeup-src : 1: Ip sleep wakeup mode; 2: line state wakeup > + mode; others means don't enable wakeup source of usb This sounds like a runtime decision. _why_ do you think this needs to be in the DT? > + - mediatek,u2port-num : The number should not greater than the number > + of phys This is useless. Either this is implied by the entries in the phys property, or it should be a runtime decision. Thanks, Mark. > + > +Optional properties: > + - vbus-supply : Reference to the VBUS regulator; > + > +Example: > +usb: usb@11270000 { > + compatible = "mediatek,mt8173-xhci"; > + reg = <0 0x11270000 0 0x4000>, > + <0 0x11280000 0 0x0800>; > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > + clocks = <&topckgen CLK_TOP_USB30_SEL>, > + <&pericfg CLK_PERI_USB0>, > + <&pericfg CLK_PERI_USB1>; > + clock-names = "sys_mac", > + "wakeup_deb_p0", > + "wakeup_deb_p1"; > + phys = <&u3phy 0>, <&u3phy 1>; > + phy-names = "usb-phy0", "usb-phy1"; > + vusb33-supply = <&mt6397_vusb_reg>; > + vbus-supply = <&usb_p1_vbus>; > + usb3-lpm-capable; > + mediatek,usb-wakeup = <&pericfg>; > + mediatek,wakeup-src = <1>; > + mediatek,u2port-num = <2>; > + status = "okay"; > +}; > -- > 1.8.1.1.dirty >
hi, On Fri, 2015-07-31 at 14:45 +0100, Mark Rutland wrote: > Hi, > > Sorry for my late reply to a prior version of this series, but I still > have concerns with some of the properties. > > I'll repeat those below. > > On Fri, Jul 31, 2015 at 02:03:53PM +0100, Chunfeng Yun wrote: > > add a DT binding documentation of xHCI host controller for the > > MT8173 SoC from Mediatek. > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > --- > > .../devicetree/bindings/usb/mt8173-xhci.txt | 51 ++++++++++++++++++++++ > > 1 file changed, 51 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt > > > > diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt > > new file mode 100644 > > index 0000000..364be5a > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt > > @@ -0,0 +1,51 @@ > > +MT65XX xhci > > + > > +The device node for Mediatek SOC usb3.0 host controller > > + > > +Required properties: > > + - compatible : Supports "mediatek,mt8173-xhci" > > s/Supports/should contain/ > done > > + - reg : Specifies physical base address and size of the registers, > > + the first one for MAC, the second for IPPC > > + - interrupts : Interrupt mode, number and trigger mode > > Just specify what this logically corresponds to; the format of the > interrupts proeprty depends on the interrupt controller. > done > > + - power-domains : To enable usb's mtcmos > > Please describe what this contains. I assume you exped a single power > domain to be described, covering the whole xHCI controller? > > > + - vusb33-supply : Regulator of usb avdd3.3v > > + - clocks : Must support all clocks that xhci needs > > - clocks: a list of phandle + clock-specifier pairs, one for each entry > in clock-names. > > > + - clock-names : Should be "sys_mac" for sys and mac clocks, and > > + "wakeup_deb_p0", "wakeup_deb_p1" for wakeup debounce control > > + clocks > > This would be better as a list, e.g. > > - clock-names: should contain: > * "sys_mac" <description here if necessary> > * "wakeup_deb_p0" <description here if necessary> > * "wakeup_deb_p1" <description here if necessary> > done > Is sys_mac a single clock input line? Or is it jsut the case that a > single line feeds two inputs currently? if the latter they should be > separate entries. > It is a single clock for usb MAC, already rename it > > + - phys : List of PHY specifiers (used by generic PHY framework). > > The bracketed part should go. The bidnigns should know nothing of Linux > internals. > remove it > > + - phy-names : Must be "usb-phy0", "usb-phy1",.., "usb-phyN", based on > > + the number of PHYs as specified in @phys property. > > This is useless. > > You either don't need names, and can acquire the phys by index, or you > need names which correspond to those on the data sheet for the xHCI > controller. > Ok, re-write the phy driver, and here also make use of the new format. > > + - mediatek,usb-wakeup : To access usb wakeup control register > > Please describe what this points to (I guess it's a syscon)/ > > > + - mediatek,wakeup-src : 1: Ip sleep wakeup mode; 2: line state wakeup > > + mode; others means don't enable wakeup source of usb > > This sounds like a runtime decision. > No, the driver do not know whether to enable wakeup function or not and also don't know enable which one, except tell it. And it will set different registers of @mediatek,usb-wakeup to enable the selected wakeup mode when system enter suspend. > _why_ do you think this needs to be in the DT? > > > + - mediatek,u2port-num : The number should not greater than the number > > + of phys > > This is useless. Either this is implied by the entries in the phys > property, or it should be a runtime decision. > Yes, it can be calculated from @phys, already remove it. Thanks a lot for your suggestion > Thanks, > Mark. > > > + > > +Optional properties: > > + - vbus-supply : Reference to the VBUS regulator; > > + > > +Example: > > +usb: usb@11270000 { > > + compatible = "mediatek,mt8173-xhci"; > > + reg = <0 0x11270000 0 0x4000>, > > + <0 0x11280000 0 0x0800>; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>, > > + <&pericfg CLK_PERI_USB0>, > > + <&pericfg CLK_PERI_USB1>; > > + clock-names = "sys_mac", > > + "wakeup_deb_p0", > > + "wakeup_deb_p1"; > > + phys = <&u3phy 0>, <&u3phy 1>; > > + phy-names = "usb-phy0", "usb-phy1"; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + vbus-supply = <&usb_p1_vbus>; > > + usb3-lpm-capable; > > + mediatek,usb-wakeup = <&pericfg>; > > + mediatek,wakeup-src = <1>; > > + mediatek,u2port-num = <2>; > > + status = "okay"; > > +}; > > -- > > 1.8.1.1.dirty > >
diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file mode 100644 index 0000000..364be5a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt @@ -0,0 +1,51 @@ +MT65XX xhci + +The device node for Mediatek SOC usb3.0 host controller + +Required properties: + - compatible : Supports "mediatek,mt8173-xhci" + - reg : Specifies physical base address and size of the registers, + the first one for MAC, the second for IPPC + - interrupts : Interrupt mode, number and trigger mode + - power-domains : To enable usb's mtcmos + - vusb33-supply : Regulator of usb avdd3.3v + - clocks : Must support all clocks that xhci needs + - clock-names : Should be "sys_mac" for sys and mac clocks, and + "wakeup_deb_p0", "wakeup_deb_p1" for wakeup debounce control + clocks + - phys : List of PHY specifiers (used by generic PHY framework). + - phy-names : Must be "usb-phy0", "usb-phy1",.., "usb-phyN", based on + the number of PHYs as specified in @phys property. + - usb3-lpm-capable : Supports USB3 LPM + - mediatek,usb-wakeup : To access usb wakeup control register + - mediatek,wakeup-src : 1: Ip sleep wakeup mode; 2: line state wakeup + mode; others means don't enable wakeup source of usb + - mediatek,u2port-num : The number should not greater than the number + of phys + +Optional properties: + - vbus-supply : Reference to the VBUS regulator; + +Example: +usb: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x4000>, + <0 0x11280000 0 0x0800>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_mac", + "wakeup_deb_p0", + "wakeup_deb_p1"; + phys = <&u3phy 0>, <&u3phy 1>; + phy-names = "usb-phy0", "usb-phy1"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p1_vbus>; + usb3-lpm-capable; + mediatek,usb-wakeup = <&pericfg>; + mediatek,wakeup-src = <1>; + mediatek,u2port-num = <2>; + status = "okay"; +};
add a DT binding documentation of xHCI host controller for the MT8173 SoC from Mediatek. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- .../devicetree/bindings/usb/mt8173-xhci.txt | 51 ++++++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt