[v2,9/9] ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board

Message ID	1441722886-22798-10-git-send-email-gary.bisson@boundarydevices.com (mailing list archive)
State	New, archived
Headers	show Return-Path: <linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org> From: Gary Bisson <gary.bisson@boundarydevices.com> To: devicetree@vger.kernel.org Subject: [PATCH v2 9/9] ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board Date: Tue, 8 Sep 2015 16:34:46 +0200 Message-Id: <1441722886-22798-10-git-send-email-gary.bisson@boundarydevices.com> In-Reply-To: <1441722886-22798-1-git-send-email-gary.bisson@boundarydevices.com> References: <1441645069-27263-1-git-send-email-gary.bisson@boundarydevices.com> <1441722886-22798-1-git-send-email-gary.bisson@boundarydevices.com> Precedence: list Cc: fabio.estevam@freescale.com, linux@arm.linux.org.uk, p.zabel@pengutronix.de, Gary Bisson <gary.bisson@boundarydevices.com>, robh+dt@kernel.org, kernel@pengutronix.de, shawn.guo@linaro.org, linux-arm-kernel@lists.infradead.org MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "linux-arm-kernel" <linux-arm-kernel-bounces@lists.infradead.org> Errors-To: linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index cc29515..b4afb42 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -284,6 +284,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-hummingboard.dtb \ + imx6dl-nit6xlite.dtb \ imx6dl-nitrogen6x.dtb \ imx6dl-phytec-pbab01.dtb \ imx6dl-rex-basic.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-nit6xlite.dts b/arch/arm/boot/dts/imx6dl-nit6xlite.dts new file mode 100644 index 0000000..e0161e4 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-nit6xlite.dts @@ -0,0 +1,49 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; + +#include "imx6dl.dtsi" +#include "imx6qdl-nit6xlite.dtsi" + +/ { + model = "Boundary Devices i.MX6 Solo Nitrogen6_Lite Board"; + compatible = "boundary,imx6dl-nit6xlite", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi new file mode 100644 index 0000000..a3b86ed --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi @@ -0,0 +1,631 @@ +/* + * Copyright 2015 Boundary Devices, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + stdout-path = &uart2; + }; + + memory { + reg = <0x10000000 0x20000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_2p5v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_wlan_vmmc: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan_vmmc>; + regulator-name = "reg_wlan_vmmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + }; + }; + + bt_rfkill { + compatible = "rfkill-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_bt_rfkill>; + gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>; + name = "bt_rfkill"; + type = <2>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + home { + label = "Home"; + gpios = <&gpio7 13 IRQ_TYPE_LEVEL_LOW>; + linux,code = <102>; + }; + + back { + label = "Back"; + gpios = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>; + linux,code = <158>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + j14-pin1 { + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j14-pin3 { + gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j14-pins8-9 { + gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j46-pin2 { + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + + j46-pin3 { + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + retain-state-suspended; + default-state = "off"; + }; + }; + + backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <&reg_3p3v>; + status = "okay"; + }; + + backlight_lvds0: backlight_lvds0 { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <&reg_3p3v>; + status = "okay"; + }; + + panel_lvds0 { + compatible = "hannstar,hsd100pxn1"; + backlight = <&backlight_lvds0>; + + port { + panel_in_lvds0: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + sound { + compatible = "fsl,imx6dl-nit6xlite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6dl-nit6xlite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, + <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "microchip,sst25vf016b"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sgtl5000>; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <&reg_2p5v>; + VDDIO-supply = <&reg_3p3v>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + ft5x06_ts@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + isl1208@6f { + compatible = "isil,isl1208"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + reg = <0x6f>; + interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_j10>; + pinctrl-1 = <&pinctrl_j28>; + + imx6dl-nit6xlite { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_bt_rfkill: bt_rfkillgrp { + fsl,pins = < + /* BT wake */ + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + /* BT reset */ + MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0b0b0 + /* BT reg en */ + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 + /* BT host wake irq */ + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x100b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x0f0b0 + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + /* Home Button: J14 pin 5 */ + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 + /* Back Button: J14 pin 7 */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + /* Touch IRQ: J7 pin 4 */ + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 + /* tcs2004 IRQ */ + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0 + /* tsc2004 reset */ + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x0b0b0 + >; + }; + + pinctrl_j10: j10grp { + fsl,pins = < + /* Broadcom WiFi module pins */ + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0 + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0 + MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0 + MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0 + >; + }; + + pinctrl_j28: j28grp { + fsl,pins = < + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0b0b0 + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x0b0b0 + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x030b0 + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x0b0b0 + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 + >; + }; + + pinctrl_wlan_vmmc: wlan_vmmcgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x030b0 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b0 + >; + }; + + pinctrl_sgtl5000: sgtl5000grp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in_lvds0>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbotg { + vbus-supply = <&reg_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + non-removable; + vmmc-supply = <&reg_3p3v>; + vqmmc-supply = <&reg_wlan_vmmc>; + vqmmc-1-8-v; + ocr-limit = <0x180>; /* 1.65v - 2.1v */ + cap-power-off-card; + keep-power-in-suspend; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; + vmmc-supply = <&reg_3p3v>; + status = "okay"; +};

[v2,9/9] ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board

Commit Message

Patch