@@ -136,6 +136,14 @@ config QCOM_SCM
bool
depends on ARM || ARM64
+config QCOM_SCM_32
+ def_bool y
+ depends on QCOM_SCM && ARM
+
+config QCOM_SCM_64
+ def_bool y
+ depends on QCOM_SCM && ARM64
+
source "drivers/firmware/broadcom/Kconfig"
source "drivers/firmware/google/Kconfig"
source "drivers/firmware/efi/Kconfig"
@@ -12,7 +12,8 @@ obj-$(CONFIG_ISCSI_IBFT_FIND) += iscsi_ibft_find.o
obj-$(CONFIG_ISCSI_IBFT) += iscsi_ibft.o
obj-$(CONFIG_FIRMWARE_MEMMAP) += memmap.o
obj-$(CONFIG_QCOM_SCM) += qcom_scm.o
-obj-$(CONFIG_QCOM_SCM) += qcom_scm-32.o
+obj-$(CONFIG_QCOM_SCM_64) += qcom_scm-64.o
+obj-$(CONFIG_QCOM_SCM_32) += qcom_scm-32.o
CFLAGS_qcom_scm-32.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
obj-y += broadcom/
new file mode 100644
@@ -0,0 +1,63 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/qcom_scm.h>
+
+/**
+ * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
+ * @entry: Entry point function for the cpus
+ * @cpus: The cpumask of cpus that will use the entry point
+ *
+ * Set the cold boot address of the cpus. Any cpu outside the supported
+ * range would be removed from the cpu present mask.
+ */
+int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus)
+{
+ return -ENOTSUPP;
+}
+
+/**
+ * qcom_scm_set_warm_boot_addr() - Set the warm boot address for cpus
+ * @entry: Entry point function for the cpus
+ * @cpus: The cpumask of cpus that will use the entry point
+ *
+ * Set the Linux entry point for the SCM to transfer control to when coming
+ * out of a power down. CPU power down may be executed on cpuidle or hotplug.
+ */
+int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
+{
+ return -ENOTSUPP;
+}
+
+/**
+ * qcom_scm_cpu_power_down() - Power down the cpu
+ * @flags - Flags to flush cache
+ *
+ * This is an end point to power down cpu. If there was a pending interrupt,
+ * the control would return from this function, otherwise, the cpu jumps to the
+ * warm boot entry point set for this cpu upon reset.
+ */
+void __qcom_scm_cpu_power_down(u32 flags)
+{
+}
+
+int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id)
+{
+ return -ENOTSUPP;
+}
+
+int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
+{
+ return -ENOTSUPP;
+}
This patch adds stubs for the SCM functions exposed in the QCOM SCM API. Signed-off-by: Andy Gross <agross@codeaurora.org> --- drivers/firmware/Kconfig | 8 +++++ drivers/firmware/Makefile | 3 +- drivers/firmware/qcom_scm-64.c | 63 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+), 1 deletion(-) create mode 100644 drivers/firmware/qcom_scm-64.c