@@ -17,11 +17,14 @@
compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
aliases {
- serial0 = &uart0;
+ serial0 = &uart0; /* On board UART0 */
+ serial1 = &uart1; /* BT UART */
+ serial2 = &uart2; /* LS Expansion UART0 */
+ serial3 = &uart3; /* LS Expansion UART1 */
};
chosen {
- stdout-path = "serial0:115200n8";
+ stdout-path = "serial3:115200n8";
};
memory@0 {
@@ -5,6 +5,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/hi6220-clock.h>
/ {
compatible = "hisilicon,hi6220";
@@ -164,8 +165,48 @@
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xf8015000 0x0 0x1000>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ao_ctrl 36>, <&ao_ctrl 36>;
+ clocks = <&ao_ctrl HI6220_UART0_PCLK>,
+ <&ao_ctrl HI6220_UART0_PCLK>;
clock-names = "uartclk", "apb_pclk";
};
+
+ uart1: uart@f7111000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xf7111000 0x0 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sys_ctrl HI6220_UART1_PCLK>,
+ <&sys_ctrl HI6220_UART1_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart2: uart@f7112000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xf7112000 0x0 0x1000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sys_ctrl HI6220_UART2_PCLK>,
+ <&sys_ctrl HI6220_UART2_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart3: uart@f7113000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xf7113000 0x0 0x1000>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sys_ctrl HI6220_UART3_PCLK>,
+ <&sys_ctrl HI6220_UART3_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ uart4: uart@f7114000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xf7114000 0x0 0x1000>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sys_ctrl HI6220_UART4_PCLK>,
+ <&sys_ctrl HI6220_UART4_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
};
};
This patch adds all UART nodes for the Hi6220 SoC. Recently a board[1] has been developed to standardize UART access across all the 96boards consumer edition boards. To use this hardware on HiKey we must configure and enable UART3. However, to ensure backward compatibility we must keep UART0 enabled as well. I have removed the hard coded clock index values in favor of using the ones already defined in include/dt-bindings/clock/hi6220-clock.h. Since UART0 needs to be soldered, it has been suggested to use the UART3 as the default console. This patch was boot tested on top of next-20150930, with both UART configurations. [1] http://www.seeedstudio.com/depot/96Boards-UART-p-2525.html?ref=newInBazaar Signed-off-by: Tyler Baker <tyler.baker@linaro.org> --- In v2: - Drop unused alias, and add comments. (Arnd, Rob) - Switch default console to use UART3 with stdout-path. (Mark, Rob) arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 7 +++-- arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 43 +++++++++++++++++++++++++- 2 files changed, 47 insertions(+), 3 deletions(-)