@@ -103,13 +103,37 @@ static u32 isi_readl(struct atmel_isi *isi, u32 reg)
return readl(isi->regs + reg);
}
+static u32 setup_cfg2_yuv_swap(struct atmel_isi *isi,
+ const struct soc_camera_format_xlate *xlate)
+{
+ if (xlate->host_fmt->fourcc == V4L2_PIX_FMT_YUYV) {
+ /* all convert to YUYV */
+ switch (xlate->code) {
+ case MEDIA_BUS_FMT_VYUY8_2X8:
+ return ISI_CFG2_YCC_SWAP_MODE_3;
+ case MEDIA_BUS_FMT_UYVY8_2X8:
+ return ISI_CFG2_YCC_SWAP_MODE_2;
+ case MEDIA_BUS_FMT_YVYU8_2X8:
+ return ISI_CFG2_YCC_SWAP_MODE_1;
+ }
+ }
+
+ /*
+ * By default, no swap for the codec path of Atmel ISI. So codec
+ * output is same as sensor's output.
+ * For instance, if sensor's output is YUYV, then codec outputs YUYV.
+ * And if sensor's output is UYVY, then codec outputs UYVY.
+ */
+ return ISI_CFG2_YCC_SWAP_DEFAULT;
+}
+
static void configure_geometry(struct atmel_isi *isi, u32 width,
- u32 height, u32 code)
+ u32 height, const struct soc_camera_format_xlate *xlate)
{
u32 cfg2;
/* According to sensor's output format to set cfg2 */
- switch (code) {
+ switch (xlate->code) {
default:
/* Grey */
case MEDIA_BUS_FMT_Y8_1X8:
@@ -117,16 +141,11 @@ static void configure_geometry(struct atmel_isi *isi, u32 width,
break;
/* YUV */
case MEDIA_BUS_FMT_VYUY8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_3 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_UYVY8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_2 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_YVYU8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_MODE_1 | ISI_CFG2_COL_SPACE_YCbCr;
- break;
case MEDIA_BUS_FMT_YUYV8_2X8:
- cfg2 = ISI_CFG2_YCC_SWAP_DEFAULT | ISI_CFG2_COL_SPACE_YCbCr;
+ cfg2 = ISI_CFG2_COL_SPACE_YCbCr |
+ setup_cfg2_yuv_swap(isi, xlate);
break;
/* RGB, TODO */
}
@@ -407,7 +426,7 @@ static int start_streaming(struct vb2_queue *vq, unsigned int count)
isi_writel(isi, ISI_INTDIS, (u32)~0UL);
configure_geometry(isi, icd->user_width, icd->user_height,
- icd->current_fmt->code);
+ icd->current_fmt);
spin_lock_irq(&isi->lock);
/* Clear any pending interrupt */
we need to configure the YCC_SWAP bits in ISI_CFG2 according to current sensor output and Atmel ISI output format. Current there are two cases Atmel ISI supported: 1. Atmel ISI outputs YUYV format. This case we need to setup YCC_SWAP according to sensor output format. 2. Atmel ISI output a pass-through formats, which means no swap. Just setup YCC_SWAP as default with no swap. Signed-off-by: Josh Wu <josh.wu@atmel.com> --- Changes in v2: - remove the duplicated variable: cfg2_yuv_swap. drivers/media/platform/soc_camera/atmel-isi.c | 39 ++++++++++++++++++++------- 1 file changed, 29 insertions(+), 10 deletions(-)