@@ -92,8 +92,8 @@
scpi_clk: scpi_clocks@3 {
compatible = "arm,scpi-variable-clocks";
#clock-cells = <1>;
- clock-indices = <3>, <4>;
- clock-output-names = "pxlclk0", "pxlclk1";
+ clock-indices = <3>;
+ clock-output-names = "pxlclk";
};
};
@@ -123,6 +123,34 @@
clock-names = "apb_pclk";
};
+ hdlcd@7ff50000 {
+ compatible = "arm,hdlcd";
+ reg = <0 0x7ff50000 0 0x1000>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scpi_clk 3>;
+ clock-names = "pxlclk";
+
+ port {
+ hdlcd1_output: endpoint@0 {
+ remote-endpoint = <&tda998x_1_input>;
+ };
+ };
+ };
+
+ hdlcd@7ff60000 {
+ compatible = "arm,hdlcd";
+ reg = <0 0x7ff60000 0 0x1000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scpi_clk 3>;
+ clock-names = "pxlclk";
+
+ port {
+ hdlcd0_output: endpoint@0 {
+ remote-endpoint = <&tda998x_0_input>;
+ };
+ };
+ };
+
soc_uart0: uart@7ff80000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0x7ff80000 0x0 0x1000>;
@@ -141,14 +169,32 @@
i2c-sda-hold-time-ns = <500>;
clocks = <&soc_smc50mhz>;
- dvi0: dvi-transmitter@70 {
+ hdmi-transmitter@70 {
compatible = "nxp,tda998x";
reg = <0x70>;
+ port {
+ tda998x_0_input: endpoint@0 {
+ remote-endpoint = <&hdlcd0_output>;
+ };
+
+ tda998x_0_output: endpoint@1 {
+ remote-endpoint = <&hdmi0_connector_output>;
+ };
+ };
};
- dvi1: dvi-transmitter@71 {
+ hdmi-transmitter@71 {
compatible = "nxp,tda998x";
reg = <0x71>;
+ port {
+ tda998x_1_input: endpoint@0 {
+ remote-endpoint = <&hdlcd1_output>;
+ };
+
+ tda998x_1_output: endpoint@1 {
+ remote-endpoint = <&hdmi1_connector_output>;
+ };
+ };
};
};
@@ -182,6 +228,26 @@
<0x00000008 0x80000000 0x1 0x80000000>;
};
+ hdmi0: connector@0 {
+ compatible = "hdmi-connector";
+ type = "a";
+ port {
+ hdmi0_connector_output: endpoint {
+ remote-endpoint = <&tda998x_0_output>;
+ };
+ };
+ };
+
+ hdmi1: connector@1 {
+ compatible = "hdmi-connector";
+ type = "a";
+ port {
+ hdmi1_connector_output: endpoint {
+ remote-endpoint = <&tda998x_1_output>;
+ };
+ };
+ };
+
smb {
compatible = "simple-bus";
#address-cells = <2>;
ARM's Juno board has two HDLCD controllers, each linked to an NXP TDA19988 HDMI transmitter that provides output encoding. Add them to the device tree. Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com> --- arch/arm64/boot/dts/arm/juno-base.dtsi | 74 ++++++++++++++++++++++++++++++++-- 1 file changed, 70 insertions(+), 4 deletions(-)