diff mbox

[1/2] ARM: dts: qcom: Remove size elements from pmic reg properties

Message ID 1448490457-9799-2-git-send-email-sboyd@codeaurora.org (mailing list archive)
State New, archived
Headers show

Commit Message

Stephen Boyd Nov. 25, 2015, 10:27 p.m. UTC 
The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/boot/dts/qcom-pm8841.dtsi |  4 ++--
 arch/arm/boot/dts/qcom-pm8941.dtsi | 22 +++++++++++-----------
 2 files changed, 13 insertions(+), 13 deletions(-)

Comments

Andy Gross Dec. 16, 2015, 8:44 p.m. UTC | #1 
On Wed, Nov 25, 2015 at 02:27:36PM -0800, Stephen Boyd wrote:
> The #size-cells for the pmics are 0, but we specify a size in the
> reg property so that MPP and GPIO modules can figure out how many
> pins there are. Now that we've done that by counting irqs, we can
> remove the size elements in the reg properties and be DT
> compliant.
> 
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Acked-by: Andy Gross <andy.gross@linaro.org>
diff mbox

Patch

diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi
index 9f357f68713c..0512f645922e 100644
--- a/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8841.dtsi
@@ -11,7 +11,7 @@ 
 
 		pm8841_mpps: mpps@a000 {
 			compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
-			reg = <0xa000 0x400>;
+			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <4 0xa0 0 IRQ_TYPE_NONE>,
@@ -22,7 +22,7 @@ 
 
 		temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
-			reg = <0x2400 0x100>;
+			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 64622bd251d1..3960b96273ec 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -12,15 +12,15 @@ 
 
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
-			reg = <0x6000 0x100>,
-			      <0x6100 0x100>;
+			reg = <0x6000>,
+			      <0x6100>;
 			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		pwrkey@800 {
 			compatible = "qcom,pm8941-pwrkey";
-			reg = <0x800 0x100>;
+			reg = <0x800>;
 			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 			debounce = <15625>;
 			bias-pull-up;
@@ -28,7 +28,7 @@ 
 
 		charger@1000 {
 			compatible = "qcom,pm8941-charger";
-			reg = <0x1000 0x700>;
+			reg = <0x1000>;
 			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
 				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
 				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
@@ -49,7 +49,7 @@ 
 
 		pm8941_gpios: gpios@c000 {
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
-			reg = <0xc000 0x2400>;
+			reg = <0xc000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
@@ -92,7 +92,7 @@ 
 
 		pm8941_mpps: mpps@a000 {
 			compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
-			reg = <0xa000 0x800>;
+			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
@@ -107,7 +107,7 @@ 
 
 		pm8941_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
-			reg = <0x2400 0x100>;
+			reg = <0x2400>;
 			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
 			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
 			io-channel-names = "thermal";
@@ -116,7 +116,7 @@ 
 
 		pm8941_vadc: vadc@3100 {
 			compatible = "qcom,spmi-vadc";
-			reg = <0x3100 0x100>;
+			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -141,14 +141,14 @@ 
 
 		pm8941_iadc: iadc@3600 {
 			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
-			reg = <0x3600 0x100>;
+			reg = <0x3600>;
 			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
 
 		coincell@2800 {
 			compatible = "qcom,pm8941-coincell";
-			reg = <0x2800 0x100>;
+			reg = <0x2800>;
 			status = "disabled";
 		};
 	};
@@ -161,7 +161,7 @@ 
 
 		wled@d800 {
 			compatible = "qcom,pm8941-wled";
-			reg = <0xd800 0x100>;
+			reg = <0xd800>;
 			label = "backlight";
 
 			qcom,cs-out;