| Message ID | 1449725588-9438-1-git-send-email-ulli.kroll@googlemail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, Dec 10, 2015 at 06:33:08AM +0100, Hans Ulli Kroll wrote: > Add a new DTS file to support the Zyxel NSA325(v2) dual bay > NAS device, based on the NSA320 DTS files. > > The only difference to the NSA320 device is GPIO47. > This en/disables the power for the hdd in slot2, currently > fixed to on. > > Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Looks good. Thanks Acked-by: Andrew Lunn <andrew@lunn.ch> Andrew > --- > > v2 > - using kirkwood-nsa325.dts as template, this removes the odd > indentation and unneeded partitions nodes. > > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/kirkwood-nsa325.dts | 236 ++++++++++++++++++++++++++++++++++ > 2 files changed, 237 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-nsa325.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index bb8fa02..0fcae90 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -193,6 +193,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ > kirkwood-ns2mini.dtb \ > kirkwood-nsa310.dtb \ > kirkwood-nsa310a.dtb \ > + kirkwood-nsa325.dtb \ > kirkwood-openblocks_a6.dtb \ > kirkwood-openblocks_a7.dtb \ > kirkwood-openrd-base.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/kirkwood-nsa325.dts > new file mode 100644 > index 0000000..6e9ffb5 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-nsa325.dts > @@ -0,0 +1,236 @@ > +/* Device tree file for the Zyxel NSA 325 NAS box. > + * > + * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com> > + * > + * This program is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License > + * as published by the Free Software Foundation; either version > + * 2 of the License, or (at your option) any later version. > + * > + * Based upon the board setup file created by Peter Schildmann */ > + > +/dts-v1/; > + > +#include "kirkwood-nsa3x0-common.dtsi" > + > +/ { > + model = "ZyXEL NSA325"; > + compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x20000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200"; > + stdout-path = &uart0; > + }; > + > + mbus { > + pcie-controller { > + status = "okay"; > + > + pcie@1,0 { > + status = "okay"; > + }; > + }; > + }; > + > + ocp@f1000000 { > + pinctrl: pin-controller@10000 { > + pinctrl-names = "default"; > + > + pmx_led_hdd2_green: pmx-led-hdd2-green { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_hdd2_red: pmx-led-hdd2-red { > + marvell,pins = "mpp13"; > + marvell,function = "gpio"; > + }; > + > + pmx_mcu_data: pmx-mcu-data { > + marvell,pins = "mpp14"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_usb_green: pmx-led-usb-green { > + marvell,pins = "mpp15"; > + marvell,function = "gpio"; > + }; > + > + pmx_mcu_clk: pmx-mcu-clk { > + marvell,pins = "mpp16"; > + marvell,function = "gpio"; > + }; > + > + pmx_mcu_act: pmx-mcu-act { > + marvell,pins = "mpp17"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_sys_green: pmx-led-sys-green { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_sys_orange: pmx-led-sys-orange { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_hdd1_green: pmx-led-hdd1-green { > + marvell,pins = "mpp41"; > + marvell,function = "gpio"; > + }; > + > + pmx_led_hdd1_red: pmx-led-hdd1-red { > + marvell,pins = "mpp42"; > + marvell,function = "gpio"; > + }; > + > + pmx_htp: pmx-htp { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + > + /* Buzzer needs to be switched at around 1kHz so is > + not compatible with the gpio-beeper driver. */ > + pmx_buzzer: pmx-buzzer { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_vid_b1: pmx-vid-b1 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + > + pmx_power_resume_data: pmx-power-resume-data { > + marvell,pins = "mpp47"; > + marvell,function = "gpio"; > + }; > + > + pmx_power_resume_clk: pmx-power-resume-clk { > + marvell,pins = "mpp49"; > + marvell,function = "gpio"; > + }; > + > + pmx_pwr_sata1: pmx-pwr-sata1 { > + marvell,pins = "mpp47"; > + marvell,function = "gpio"; > + }; > + }; > + > + /* This board uses the pcf8563 RTC instead of the SoC RTC */ > + rtc@10300 { > + status = "disabled"; > + }; > + > + i2c@11000 { > + status = "okay"; > + > + pcf8563: pcf8563@51 { > + compatible = "nxp,pcf8563"; > + reg = <0x51>; > + }; > + }; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_pwr_sata1>; > + pinctrl-names = "default"; > + > + usb0_power: regulator@1 { > + enable-active-high; > + }; > + > + sata1_power: regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "SATA1 Power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + enable-active-high; > + gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red > + &pmx_led_usb_green > + &pmx_led_sys_green &pmx_led_sys_orange > + &pmx_led_copy_green &pmx_led_copy_red > + &pmx_led_hdd1_green &pmx_led_hdd1_red>; > + pinctrl-names = "default"; > + > + green-sys { > + label = "nsa325:green:sys"; > + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; > + }; > + orange-sys { > + label = "nsa325:orange:sys"; > + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; > + }; > + green-hdd1 { > + label = "nsa325:green:hdd1"; > + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; > + }; > + red-hdd1 { > + label = "nsa325:red:hdd1"; > + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; > + }; > + green-hdd2 { > + label = "nsa325:green:hdd2"; > + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + }; > + red-hdd2 { > + label = "nsa325:red:hdd2"; > + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; > + }; > + green-usb { > + label = "nsa325:green:usb"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; > + }; > + green-copy { > + label = "nsa325:green:copy"; > + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + }; > + red-copy { > + label = "nsa325:red:copy"; > + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; > + }; > + > + /* The following pins are currently not assigned to a driver, > + some of them should be configured as inputs. > + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act > + &pmx_htp &pmx_vid_b1 > + &pmx_power_resume_data &pmx_power_resume_clk>; */ > + > + }; > + > + > +}; > + > +&mdio { > + status = "okay"; > + ethphy0: ethernet-phy@1 { > + reg = <1>; > + }; > +}; > + > +ð0 { > + status = "okay"; > + ethernet0-port@0 { > + phy-handle = <ðphy0>; > + }; > +}; > + > -- > 2.6.0 >
Hi Hans, On jeu., déc. 10 2015, Andrew Lunn <andrew@lunn.ch> wrote: > On Thu, Dec 10, 2015 at 06:33:08AM +0100, Hans Ulli Kroll wrote: >> Add a new DTS file to support the Zyxel NSA325(v2) dual bay >> NAS device, based on the NSA320 DTS files. >> >> The only difference to the NSA320 device is GPIO47. >> This en/disables the power for the hdd in slot2, currently >> fixed to on. >> >> Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> > > Looks good. Thanks > > Acked-by: Andrew Lunn <andrew@lunn.ch> Applied on mvebu/dt with Andrew's acked-by and minor fix on comment format. Thanks, Gregory > > Andrew > >> --- >> >> v2 >> - using kirkwood-nsa325.dts as template, this removes the odd >> indentation and unneeded partitions nodes. >> >> arch/arm/boot/dts/Makefile | 1 + >> arch/arm/boot/dts/kirkwood-nsa325.dts | 236 ++++++++++++++++++++++++++++++++++ >> 2 files changed, 237 insertions(+) >> create mode 100644 arch/arm/boot/dts/kirkwood-nsa325.dts >> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >> index bb8fa02..0fcae90 100644 >> --- a/arch/arm/boot/dts/Makefile >> +++ b/arch/arm/boot/dts/Makefile >> @@ -193,6 +193,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ >> kirkwood-ns2mini.dtb \ >> kirkwood-nsa310.dtb \ >> kirkwood-nsa310a.dtb \ >> + kirkwood-nsa325.dtb \ >> kirkwood-openblocks_a6.dtb \ >> kirkwood-openblocks_a7.dtb \ >> kirkwood-openrd-base.dtb \ >> diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/kirkwood-nsa325.dts >> new file mode 100644 >> index 0000000..6e9ffb5 >> --- /dev/null >> +++ b/arch/arm/boot/dts/kirkwood-nsa325.dts >> @@ -0,0 +1,236 @@ >> +/* Device tree file for the Zyxel NSA 325 NAS box. >> + * >> + * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com> >> + * >> + * This program is free software; you can redistribute it and/or >> + * modify it under the terms of the GNU General Public License >> + * as published by the Free Software Foundation; either version >> + * 2 of the License, or (at your option) any later version. >> + * >> + * Based upon the board setup file created by Peter Schildmann */ >> + >> +/dts-v1/; >> + >> +#include "kirkwood-nsa3x0-common.dtsi" >> + >> +/ { >> + model = "ZyXEL NSA325"; >> + compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; >> + >> + memory { >> + device_type = "memory"; >> + reg = <0x00000000 0x20000000>; >> + }; >> + >> + chosen { >> + bootargs = "console=ttyS0,115200"; >> + stdout-path = &uart0; >> + }; >> + >> + mbus { >> + pcie-controller { >> + status = "okay"; >> + >> + pcie@1,0 { >> + status = "okay"; >> + }; >> + }; >> + }; >> + >> + ocp@f1000000 { >> + pinctrl: pin-controller@10000 { >> + pinctrl-names = "default"; >> + >> + pmx_led_hdd2_green: pmx-led-hdd2-green { >> + marvell,pins = "mpp12"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_hdd2_red: pmx-led-hdd2-red { >> + marvell,pins = "mpp13"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_mcu_data: pmx-mcu-data { >> + marvell,pins = "mpp14"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_usb_green: pmx-led-usb-green { >> + marvell,pins = "mpp15"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_mcu_clk: pmx-mcu-clk { >> + marvell,pins = "mpp16"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_mcu_act: pmx-mcu-act { >> + marvell,pins = "mpp17"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_sys_green: pmx-led-sys-green { >> + marvell,pins = "mpp28"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_sys_orange: pmx-led-sys-orange { >> + marvell,pins = "mpp29"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_hdd1_green: pmx-led-hdd1-green { >> + marvell,pins = "mpp41"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_led_hdd1_red: pmx-led-hdd1-red { >> + marvell,pins = "mpp42"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_htp: pmx-htp { >> + marvell,pins = "mpp43"; >> + marvell,function = "gpio"; >> + }; >> + >> + /* Buzzer needs to be switched at around 1kHz so is >> + not compatible with the gpio-beeper driver. */ >> + pmx_buzzer: pmx-buzzer { >> + marvell,pins = "mpp44"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_vid_b1: pmx-vid-b1 { >> + marvell,pins = "mpp45"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_power_resume_data: pmx-power-resume-data { >> + marvell,pins = "mpp47"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_power_resume_clk: pmx-power-resume-clk { >> + marvell,pins = "mpp49"; >> + marvell,function = "gpio"; >> + }; >> + >> + pmx_pwr_sata1: pmx-pwr-sata1 { >> + marvell,pins = "mpp47"; >> + marvell,function = "gpio"; >> + }; >> + }; >> + >> + /* This board uses the pcf8563 RTC instead of the SoC RTC */ >> + rtc@10300 { >> + status = "disabled"; >> + }; >> + >> + i2c@11000 { >> + status = "okay"; >> + >> + pcf8563: pcf8563@51 { >> + compatible = "nxp,pcf8563"; >> + reg = <0x51>; >> + }; >> + }; >> + }; >> + >> + regulators { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + pinctrl-0 = <&pmx_pwr_sata1>; >> + pinctrl-names = "default"; >> + >> + usb0_power: regulator@1 { >> + enable-active-high; >> + }; >> + >> + sata1_power: regulator@2 { >> + compatible = "regulator-fixed"; >> + reg = <2>; >> + regulator-name = "SATA1 Power"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + regulator-always-on; >> + regulator-boot-on; >> + enable-active-high; >> + gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; >> + }; >> + }; >> + >> + gpio-leds { >> + compatible = "gpio-leds"; >> + pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red >> + &pmx_led_usb_green >> + &pmx_led_sys_green &pmx_led_sys_orange >> + &pmx_led_copy_green &pmx_led_copy_red >> + &pmx_led_hdd1_green &pmx_led_hdd1_red>; >> + pinctrl-names = "default"; >> + >> + green-sys { >> + label = "nsa325:green:sys"; >> + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; >> + }; >> + orange-sys { >> + label = "nsa325:orange:sys"; >> + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; >> + }; >> + green-hdd1 { >> + label = "nsa325:green:hdd1"; >> + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; >> + }; >> + red-hdd1 { >> + label = "nsa325:red:hdd1"; >> + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; >> + }; >> + green-hdd2 { >> + label = "nsa325:green:hdd2"; >> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; >> + }; >> + red-hdd2 { >> + label = "nsa325:red:hdd2"; >> + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; >> + }; >> + green-usb { >> + label = "nsa325:green:usb"; >> + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; >> + }; >> + green-copy { >> + label = "nsa325:green:copy"; >> + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; >> + }; >> + red-copy { >> + label = "nsa325:red:copy"; >> + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; >> + }; >> + >> + /* The following pins are currently not assigned to a driver, >> + some of them should be configured as inputs. >> + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act >> + &pmx_htp &pmx_vid_b1 >> + &pmx_power_resume_data &pmx_power_resume_clk>; */ >> + >> + }; >> + >> + >> +}; >> + >> +&mdio { >> + status = "okay"; >> + ethphy0: ethernet-phy@1 { >> + reg = <1>; >> + }; >> +}; >> + >> +ð0 { >> + status = "okay"; >> + ethernet0-port@0 { >> + phy-handle = <ðphy0>; >> + }; >> +}; >> + >> -- >> 2.6.0 >>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bb8fa02..0fcae90 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -193,6 +193,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-ns2mini.dtb \ kirkwood-nsa310.dtb \ kirkwood-nsa310a.dtb \ + kirkwood-nsa325.dtb \ kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a7.dtb \ kirkwood-openrd-base.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/kirkwood-nsa325.dts new file mode 100644 index 0000000..6e9ffb5 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-nsa325.dts @@ -0,0 +1,236 @@ +/* Device tree file for the Zyxel NSA 325 NAS box. + * + * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Based upon the board setup file created by Peter Schildmann */ + +/dts-v1/; + +#include "kirkwood-nsa3x0-common.dtsi" + +/ { + model = "ZyXEL NSA325"; + compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_led_hdd2_green: pmx-led-hdd2-green { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_led_hdd2_red: pmx-led-hdd2-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_mcu_data: pmx-mcu-data { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_mcu_clk: pmx-mcu-clk { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_mcu_act: pmx-mcu-act { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_orange: pmx-led-sys-orange { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_green: pmx-led-hdd1-green { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_led_hdd1_red: pmx-led-hdd1-red { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + pmx_htp: pmx-htp { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + /* Buzzer needs to be switched at around 1kHz so is + not compatible with the gpio-beeper driver. */ + pmx_buzzer: pmx-buzzer { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_vid_b1: pmx-vid-b1 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_power_resume_data: pmx-power-resume-data { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_power_resume_clk: pmx-power-resume-clk { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + + pmx_pwr_sata1: pmx-pwr-sata1 { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; + + /* This board uses the pcf8563 RTC instead of the SoC RTC */ + rtc@10300 { + status = "disabled"; + }; + + i2c@11000 { + status = "okay"; + + pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_pwr_sata1>; + pinctrl-names = "default"; + + usb0_power: regulator@1 { + enable-active-high; + }; + + sata1_power: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA1 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red + &pmx_led_usb_green + &pmx_led_sys_green &pmx_led_sys_orange + &pmx_led_copy_green &pmx_led_copy_red + &pmx_led_hdd1_green &pmx_led_hdd1_red>; + pinctrl-names = "default"; + + green-sys { + label = "nsa325:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; + orange-sys { + label = "nsa325:orange:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd1 { + label = "nsa325:green:hdd1"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + red-hdd1 { + label = "nsa325:red:hdd1"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + green-hdd2 { + label = "nsa325:green:hdd2"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + red-hdd2 { + label = "nsa325:red:hdd2"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + green-usb { + label = "nsa325:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + green-copy { + label = "nsa325:green:copy"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + red-copy { + label = "nsa325:red:copy"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + + /* The following pins are currently not assigned to a driver, + some of them should be configured as inputs. + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act + &pmx_htp &pmx_vid_b1 + &pmx_power_resume_data &pmx_power_resume_clk>; */ + + }; + + +}; + +&mdio { + status = "okay"; + ethphy0: ethernet-phy@1 { + reg = <1>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; +
Add a new DTS file to support the Zyxel NSA325(v2) dual bay NAS device, based on the NSA320 DTS files. The only difference to the NSA320 device is GPIO47. This en/disables the power for the hdd in slot2, currently fixed to on. Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> --- v2 - using kirkwood-nsa325.dts as template, this removes the odd indentation and unneeded partitions nodes. arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-nsa325.dts | 236 ++++++++++++++++++++++++++++++++++ 2 files changed, 237 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-nsa325.dts