| Message ID | 1452655854-1528-6-git-send-email-wens@csie.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Wed, 13 Jan 2016, Chen-Yu Tsai wrote: > The axp20x driver assumes the device is i2c based. This is not the > case with later chips, which use a proprietary 2 wire serial bus > by Allwinner called "Reduced Serial Bus". > > This patch follows the example of mfd/wm831x and splits it into > an interface independent core, and an i2c specific glue layer. > MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate > symbols, allowing the driver to be built as modules. > > Whitespace and other style errors in the moved i2c specific code > have been fixed. Included but unused header files are removed as > well. > > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > --- > > Changes since v6: > > - Drop filenames from file headers > > --- > drivers/mfd/Kconfig | 14 +++--- > drivers/mfd/Makefile | 1 + > drivers/mfd/axp20x-i2c.c | 104 +++++++++++++++++++++++++++++++++++++++++++++ > drivers/mfd/axp20x.c | 90 +++++++-------------------------------- > include/linux/mfd/axp20x.h | 33 +++++++++++++- > 5 files changed, 161 insertions(+), 81 deletions(-) > create mode 100644 drivers/mfd/axp20x-i2c.c Acked-by: Lee Jones <lee.jones@linaro.org> > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 4d92df6ef9fe..804cd3dcce32 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -91,14 +91,18 @@ config MFD_BCM590XX > Support for the BCM590xx PMUs from Broadcom > > config MFD_AXP20X > - bool "X-Powers AXP20X" > + tristate > select MFD_CORE > - select REGMAP_I2C > select REGMAP_IRQ > - depends on I2C=y > + > +config MFD_AXP20X_I2C > + tristate "X-Powers AXP series PMICs with I2C" > + select MFD_AXP20X > + select REGMAP_I2C > + depends on I2C > help > - If you say Y here you get support for the X-Powers AXP202, AXP209 and > - AXP288 power management IC (PMIC). > + If you say Y here you get support for the X-Powers AXP series power > + management ICs (PMICs) controlled with I2C. > This driver include only the core APIs. You have to select individual > components like regulators or the PEK (Power Enable Key) under the > corresponding menus. > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index a8b76b81b467..a6913007d667 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -107,6 +107,7 @@ obj-$(CONFIG_PMIC_DA9052) += da9052-core.o > obj-$(CONFIG_MFD_DA9052_SPI) += da9052-spi.o > obj-$(CONFIG_MFD_DA9052_I2C) += da9052-i2c.o > obj-$(CONFIG_MFD_AXP20X) += axp20x.o > +obj-$(CONFIG_MFD_AXP20X_I2C) += axp20x-i2c.o > > obj-$(CONFIG_MFD_LP3943) += lp3943.o > obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o > diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c > new file mode 100644 > index 000000000000..b1b865822c07 > --- /dev/null > +++ b/drivers/mfd/axp20x-i2c.c > @@ -0,0 +1,104 @@ > +/* > + * I2C driver for the X-Powers' Power Management ICs > + * > + * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC > + * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature > + * as well as configurable GPIOs. > + * > + * This driver supports the I2C variants. > + * > + * Copyright (C) 2014 Carlo Caione > + * > + * Author: Carlo Caione <carlo@caione.org> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/acpi.h> > +#include <linux/err.h> > +#include <linux/i2c.h> > +#include <linux/module.h> > +#include <linux/mfd/axp20x.h> > +#include <linux/of.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> > + > +static int axp20x_i2c_probe(struct i2c_client *i2c, > + const struct i2c_device_id *id) > +{ > + struct axp20x_dev *axp20x; > + int ret; > + > + axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL); > + if (!axp20x) > + return -ENOMEM; > + > + axp20x->dev = &i2c->dev; > + axp20x->irq = i2c->irq; > + dev_set_drvdata(axp20x->dev, axp20x); > + > + ret = axp20x_match_device(axp20x); > + if (ret) > + return ret; > + > + axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg); > + if (IS_ERR(axp20x->regmap)) { > + ret = PTR_ERR(axp20x->regmap); > + dev_err(&i2c->dev, "regmap init failed: %d\n", ret); > + return ret; > + } > + > + return axp20x_device_probe(axp20x); > +} > + > +static int axp20x_i2c_remove(struct i2c_client *i2c) > +{ > + struct axp20x_dev *axp20x = i2c_get_clientdata(i2c); > + > + return axp20x_device_remove(axp20x); > +} > + > +static const struct of_device_id axp20x_i2c_of_match[] = { > + { .compatible = "x-powers,axp152", .data = (void *)AXP152_ID }, > + { .compatible = "x-powers,axp202", .data = (void *)AXP202_ID }, > + { .compatible = "x-powers,axp209", .data = (void *)AXP209_ID }, > + { .compatible = "x-powers,axp221", .data = (void *)AXP221_ID }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match); > + > +/* > + * This is useless for OF-enabled devices, but it is needed by I2C subsystem > + */ > +static const struct i2c_device_id axp20x_i2c_id[] = { > + { }, > +}; > +MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id); > + > +static const struct acpi_device_id axp20x_i2c_acpi_match[] = { > + { > + .id = "INT33F4", > + .driver_data = AXP288_ID, > + }, > + { }, > +}; > +MODULE_DEVICE_TABLE(acpi, axp20x_i2c_acpi_match); > + > +static struct i2c_driver axp20x_i2c_driver = { > + .driver = { > + .name = "axp20x-i2c", > + .of_match_table = of_match_ptr(axp20x_i2c_of_match), > + .acpi_match_table = ACPI_PTR(axp20x_i2c_acpi_match), > + }, > + .probe = axp20x_i2c_probe, > + .remove = axp20x_i2c_remove, > + .id_table = axp20x_i2c_id, > +}; > + > +module_i2c_driver(axp20x_i2c_driver); > + > +MODULE_DESCRIPTION("PMIC MFD I2C driver for AXP20X"); > +MODULE_AUTHOR("Carlo Caione <carlo@caione.org>"); > +MODULE_LICENSE("GPL"); > diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c > index cec51e689d1d..8e569bcfe3bc 100644 > --- a/drivers/mfd/axp20x.c > +++ b/drivers/mfd/axp20x.c > @@ -1,10 +1,12 @@ > /* > - * axp20x.c - MFD core driver for the X-Powers' Power Management ICs > + * MFD core driver for the X-Powers' Power Management ICs > * > * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC > * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature > * as well as configurable GPIOs. > * > + * This file contains the interface independent core functions. > + * > * Copyright (C) 2014 Carlo Caione > * > * Author: Carlo Caione <carlo@caione.org> > @@ -15,18 +17,15 @@ > */ > > #include <linux/err.h> > -#include <linux/i2c.h> > #include <linux/interrupt.h> > #include <linux/kernel.h> > #include <linux/module.h> > #include <linux/pm_runtime.h> > #include <linux/regmap.h> > -#include <linux/slab.h> > #include <linux/regulator/consumer.h> > #include <linux/mfd/axp20x.h> > #include <linux/mfd/core.h> > #include <linux/of_device.h> > -#include <linux/of_irq.h> > #include <linux/acpi.h> > > #define AXP20X_OFF 0x80 > @@ -378,32 +377,6 @@ static const struct regmap_irq axp288_regmap_irqs[] = { > INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1), > }; > > -static const struct of_device_id axp20x_of_match[] = { > - { .compatible = "x-powers,axp152", .data = (void *) AXP152_ID }, > - { .compatible = "x-powers,axp202", .data = (void *) AXP202_ID }, > - { .compatible = "x-powers,axp209", .data = (void *) AXP209_ID }, > - { .compatible = "x-powers,axp221", .data = (void *) AXP221_ID }, > - { }, > -}; > -MODULE_DEVICE_TABLE(of, axp20x_of_match); > - > -/* > - * This is useless for OF-enabled devices, but it is needed by I2C subsystem > - */ > -static const struct i2c_device_id axp20x_i2c_id[] = { > - { }, > -}; > -MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id); > - > -static const struct acpi_device_id axp20x_acpi_match[] = { > - { > - .id = "INT33F4", > - .driver_data = AXP288_ID, > - }, > - { }, > -}; > -MODULE_DEVICE_TABLE(acpi, axp20x_acpi_match); > - > static const struct regmap_irq_chip axp152_regmap_irq_chip = { > .name = "axp152_irq_chip", > .status_base = AXP152_IRQ1_STATE, > @@ -608,7 +581,7 @@ static void axp20x_power_off(void) > AXP20X_OFF); > } > > -static int axp20x_match_device(struct axp20x_dev *axp20x) > +int axp20x_match_device(struct axp20x_dev *axp20x) > { > struct device *dev = axp20x->dev; > const struct acpi_device_id *acpi_id; > @@ -665,38 +638,18 @@ static int axp20x_match_device(struct axp20x_dev *axp20x) > > return 0; > } > +EXPORT_SYMBOL(axp20x_match_device); > > -static int axp20x_i2c_probe(struct i2c_client *i2c, > - const struct i2c_device_id *id) > +int axp20x_device_probe(struct axp20x_dev *axp20x) > { > - struct axp20x_dev *axp20x; > int ret; > > - axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL); > - if (!axp20x) > - return -ENOMEM; > - > - axp20x->i2c_client = i2c; > - axp20x->dev = &i2c->dev; > - dev_set_drvdata(axp20x->dev, axp20x); > - > - ret = axp20x_match_device(axp20x); > - if (ret) > - return ret; > - > - axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg); > - if (IS_ERR(axp20x->regmap)) { > - ret = PTR_ERR(axp20x->regmap); > - dev_err(&i2c->dev, "regmap init failed: %d\n", ret); > - return ret; > - } > - > - ret = regmap_add_irq_chip(axp20x->regmap, i2c->irq, > + ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq, > IRQF_ONESHOT | IRQF_SHARED, -1, > axp20x->regmap_irq_chip, > &axp20x->regmap_irqc); > if (ret) { > - dev_err(&i2c->dev, "failed to add irq chip: %d\n", ret); > + dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret); > return ret; > } > > @@ -704,8 +657,8 @@ static int axp20x_i2c_probe(struct i2c_client *i2c, > axp20x->nr_cells, NULL, 0, NULL); > > if (ret) { > - dev_err(&i2c->dev, "failed to add MFD devices: %d\n", ret); > - regmap_del_irq_chip(i2c->irq, axp20x->regmap_irqc); > + dev_err(axp20x->dev, "failed to add MFD devices: %d\n", ret); > + regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc); > return ret; > } > > @@ -714,38 +667,25 @@ static int axp20x_i2c_probe(struct i2c_client *i2c, > pm_power_off = axp20x_power_off; > } > > - dev_info(&i2c->dev, "AXP20X driver loaded\n"); > + dev_info(axp20x->dev, "AXP20X driver loaded\n"); > > return 0; > } > +EXPORT_SYMBOL(axp20x_device_probe); > > -static int axp20x_i2c_remove(struct i2c_client *i2c) > +int axp20x_device_remove(struct axp20x_dev *axp20x) > { > - struct axp20x_dev *axp20x = i2c_get_clientdata(i2c); > - > if (axp20x == axp20x_pm_power_off) { > axp20x_pm_power_off = NULL; > pm_power_off = NULL; > } > > mfd_remove_devices(axp20x->dev); > - regmap_del_irq_chip(axp20x->i2c_client->irq, axp20x->regmap_irqc); > + regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc); > > return 0; > } > - > -static struct i2c_driver axp20x_i2c_driver = { > - .driver = { > - .name = "axp20x", > - .of_match_table = of_match_ptr(axp20x_of_match), > - .acpi_match_table = ACPI_PTR(axp20x_acpi_match), > - }, > - .probe = axp20x_i2c_probe, > - .remove = axp20x_i2c_remove, > - .id_table = axp20x_i2c_id, > -}; > - > -module_i2c_driver(axp20x_i2c_driver); > +EXPORT_SYMBOL(axp20x_device_remove); > > MODULE_DESCRIPTION("PMIC MFD core driver for AXP20X"); > MODULE_AUTHOR("Carlo Caione <carlo@caione.org>"); > diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h > index b24c771cebd5..00697c6ad8b0 100644 > --- a/include/linux/mfd/axp20x.h > +++ b/include/linux/mfd/axp20x.h > @@ -396,7 +396,7 @@ enum axp288_irqs { > > struct axp20x_dev { > struct device *dev; > - struct i2c_client *i2c_client; > + int irq; > struct regmap *regmap; > struct regmap_irq_chip_data *regmap_irqc; > long variant; > @@ -462,4 +462,35 @@ static inline int axp20x_read_variable_width(struct regmap *regmap, > return result; > } > > +/** > + * axp20x_match_device(): Setup axp20x variant related fields > + * > + * @axp20x: axp20x device to setup (.dev field must be set) > + * @dev: device associated with this axp20x device > + * > + * This lets the axp20x core configure the mfd cells and register maps > + * for later use. > + */ > +int axp20x_match_device(struct axp20x_dev *axp20x); > + > +/** > + * axp20x_device_probe(): Probe a configured axp20x device > + * > + * @axp20x: axp20x device to probe (must be configured) > + * > + * This function lets the axp20x core register the axp20x mfd devices > + * and irqchip. The axp20x device passed in must be fully configured > + * with axp20x_match_device, its irq set, and regmap created. > + */ > +int axp20x_device_probe(struct axp20x_dev *axp20x); > + > +/** > + * axp20x_device_probe(): Remove a axp20x device > + * > + * @axp20x: axp20x device to remove > + * > + * This tells the axp20x core to remove the associated mfd devices > + */ > +int axp20x_device_remove(struct axp20x_dev *axp20x); > + > #endif /* __LINUX_MFD_AXP20X_H */
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 4d92df6ef9fe..804cd3dcce32 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -91,14 +91,18 @@ config MFD_BCM590XX Support for the BCM590xx PMUs from Broadcom config MFD_AXP20X - bool "X-Powers AXP20X" + tristate select MFD_CORE - select REGMAP_I2C select REGMAP_IRQ - depends on I2C=y + +config MFD_AXP20X_I2C + tristate "X-Powers AXP series PMICs with I2C" + select MFD_AXP20X + select REGMAP_I2C + depends on I2C help - If you say Y here you get support for the X-Powers AXP202, AXP209 and - AXP288 power management IC (PMIC). + If you say Y here you get support for the X-Powers AXP series power + management ICs (PMICs) controlled with I2C. This driver include only the core APIs. You have to select individual components like regulators or the PEK (Power Enable Key) under the corresponding menus. diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index a8b76b81b467..a6913007d667 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -107,6 +107,7 @@ obj-$(CONFIG_PMIC_DA9052) += da9052-core.o obj-$(CONFIG_MFD_DA9052_SPI) += da9052-spi.o obj-$(CONFIG_MFD_DA9052_I2C) += da9052-i2c.o obj-$(CONFIG_MFD_AXP20X) += axp20x.o +obj-$(CONFIG_MFD_AXP20X_I2C) += axp20x-i2c.o obj-$(CONFIG_MFD_LP3943) += lp3943.o obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c new file mode 100644 index 000000000000..b1b865822c07 --- /dev/null +++ b/drivers/mfd/axp20x-i2c.c @@ -0,0 +1,104 @@ +/* + * I2C driver for the X-Powers' Power Management ICs + * + * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC + * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature + * as well as configurable GPIOs. + * + * This driver supports the I2C variants. + * + * Copyright (C) 2014 Carlo Caione + * + * Author: Carlo Caione <carlo@caione.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/acpi.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/mfd/axp20x.h> +#include <linux/of.h> +#include <linux/regmap.h> +#include <linux/slab.h> + +static int axp20x_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct axp20x_dev *axp20x; + int ret; + + axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL); + if (!axp20x) + return -ENOMEM; + + axp20x->dev = &i2c->dev; + axp20x->irq = i2c->irq; + dev_set_drvdata(axp20x->dev, axp20x); + + ret = axp20x_match_device(axp20x); + if (ret) + return ret; + + axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg); + if (IS_ERR(axp20x->regmap)) { + ret = PTR_ERR(axp20x->regmap); + dev_err(&i2c->dev, "regmap init failed: %d\n", ret); + return ret; + } + + return axp20x_device_probe(axp20x); +} + +static int axp20x_i2c_remove(struct i2c_client *i2c) +{ + struct axp20x_dev *axp20x = i2c_get_clientdata(i2c); + + return axp20x_device_remove(axp20x); +} + +static const struct of_device_id axp20x_i2c_of_match[] = { + { .compatible = "x-powers,axp152", .data = (void *)AXP152_ID }, + { .compatible = "x-powers,axp202", .data = (void *)AXP202_ID }, + { .compatible = "x-powers,axp209", .data = (void *)AXP209_ID }, + { .compatible = "x-powers,axp221", .data = (void *)AXP221_ID }, + { }, +}; +MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match); + +/* + * This is useless for OF-enabled devices, but it is needed by I2C subsystem + */ +static const struct i2c_device_id axp20x_i2c_id[] = { + { }, +}; +MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id); + +static const struct acpi_device_id axp20x_i2c_acpi_match[] = { + { + .id = "INT33F4", + .driver_data = AXP288_ID, + }, + { }, +}; +MODULE_DEVICE_TABLE(acpi, axp20x_i2c_acpi_match); + +static struct i2c_driver axp20x_i2c_driver = { + .driver = { + .name = "axp20x-i2c", + .of_match_table = of_match_ptr(axp20x_i2c_of_match), + .acpi_match_table = ACPI_PTR(axp20x_i2c_acpi_match), + }, + .probe = axp20x_i2c_probe, + .remove = axp20x_i2c_remove, + .id_table = axp20x_i2c_id, +}; + +module_i2c_driver(axp20x_i2c_driver); + +MODULE_DESCRIPTION("PMIC MFD I2C driver for AXP20X"); +MODULE_AUTHOR("Carlo Caione <carlo@caione.org>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c index cec51e689d1d..8e569bcfe3bc 100644 --- a/drivers/mfd/axp20x.c +++ b/drivers/mfd/axp20x.c @@ -1,10 +1,12 @@ /* - * axp20x.c - MFD core driver for the X-Powers' Power Management ICs + * MFD core driver for the X-Powers' Power Management ICs * * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature * as well as configurable GPIOs. * + * This file contains the interface independent core functions. + * * Copyright (C) 2014 Carlo Caione * * Author: Carlo Caione <carlo@caione.org> @@ -15,18 +17,15 @@ */ #include <linux/err.h> -#include <linux/i2c.h> #include <linux/interrupt.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/pm_runtime.h> #include <linux/regmap.h> -#include <linux/slab.h> #include <linux/regulator/consumer.h> #include <linux/mfd/axp20x.h> #include <linux/mfd/core.h> #include <linux/of_device.h> -#include <linux/of_irq.h> #include <linux/acpi.h> #define AXP20X_OFF 0x80 @@ -378,32 +377,6 @@ static const struct regmap_irq axp288_regmap_irqs[] = { INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1), }; -static const struct of_device_id axp20x_of_match[] = { - { .compatible = "x-powers,axp152", .data = (void *) AXP152_ID }, - { .compatible = "x-powers,axp202", .data = (void *) AXP202_ID }, - { .compatible = "x-powers,axp209", .data = (void *) AXP209_ID }, - { .compatible = "x-powers,axp221", .data = (void *) AXP221_ID }, - { }, -}; -MODULE_DEVICE_TABLE(of, axp20x_of_match); - -/* - * This is useless for OF-enabled devices, but it is needed by I2C subsystem - */ -static const struct i2c_device_id axp20x_i2c_id[] = { - { }, -}; -MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id); - -static const struct acpi_device_id axp20x_acpi_match[] = { - { - .id = "INT33F4", - .driver_data = AXP288_ID, - }, - { }, -}; -MODULE_DEVICE_TABLE(acpi, axp20x_acpi_match); - static const struct regmap_irq_chip axp152_regmap_irq_chip = { .name = "axp152_irq_chip", .status_base = AXP152_IRQ1_STATE, @@ -608,7 +581,7 @@ static void axp20x_power_off(void) AXP20X_OFF); } -static int axp20x_match_device(struct axp20x_dev *axp20x) +int axp20x_match_device(struct axp20x_dev *axp20x) { struct device *dev = axp20x->dev; const struct acpi_device_id *acpi_id; @@ -665,38 +638,18 @@ static int axp20x_match_device(struct axp20x_dev *axp20x) return 0; } +EXPORT_SYMBOL(axp20x_match_device); -static int axp20x_i2c_probe(struct i2c_client *i2c, - const struct i2c_device_id *id) +int axp20x_device_probe(struct axp20x_dev *axp20x) { - struct axp20x_dev *axp20x; int ret; - axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL); - if (!axp20x) - return -ENOMEM; - - axp20x->i2c_client = i2c; - axp20x->dev = &i2c->dev; - dev_set_drvdata(axp20x->dev, axp20x); - - ret = axp20x_match_device(axp20x); - if (ret) - return ret; - - axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg); - if (IS_ERR(axp20x->regmap)) { - ret = PTR_ERR(axp20x->regmap); - dev_err(&i2c->dev, "regmap init failed: %d\n", ret); - return ret; - } - - ret = regmap_add_irq_chip(axp20x->regmap, i2c->irq, + ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq, IRQF_ONESHOT | IRQF_SHARED, -1, axp20x->regmap_irq_chip, &axp20x->regmap_irqc); if (ret) { - dev_err(&i2c->dev, "failed to add irq chip: %d\n", ret); + dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret); return ret; } @@ -704,8 +657,8 @@ static int axp20x_i2c_probe(struct i2c_client *i2c, axp20x->nr_cells, NULL, 0, NULL); if (ret) { - dev_err(&i2c->dev, "failed to add MFD devices: %d\n", ret); - regmap_del_irq_chip(i2c->irq, axp20x->regmap_irqc); + dev_err(axp20x->dev, "failed to add MFD devices: %d\n", ret); + regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc); return ret; } @@ -714,38 +667,25 @@ static int axp20x_i2c_probe(struct i2c_client *i2c, pm_power_off = axp20x_power_off; } - dev_info(&i2c->dev, "AXP20X driver loaded\n"); + dev_info(axp20x->dev, "AXP20X driver loaded\n"); return 0; } +EXPORT_SYMBOL(axp20x_device_probe); -static int axp20x_i2c_remove(struct i2c_client *i2c) +int axp20x_device_remove(struct axp20x_dev *axp20x) { - struct axp20x_dev *axp20x = i2c_get_clientdata(i2c); - if (axp20x == axp20x_pm_power_off) { axp20x_pm_power_off = NULL; pm_power_off = NULL; } mfd_remove_devices(axp20x->dev); - regmap_del_irq_chip(axp20x->i2c_client->irq, axp20x->regmap_irqc); + regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc); return 0; } - -static struct i2c_driver axp20x_i2c_driver = { - .driver = { - .name = "axp20x", - .of_match_table = of_match_ptr(axp20x_of_match), - .acpi_match_table = ACPI_PTR(axp20x_acpi_match), - }, - .probe = axp20x_i2c_probe, - .remove = axp20x_i2c_remove, - .id_table = axp20x_i2c_id, -}; - -module_i2c_driver(axp20x_i2c_driver); +EXPORT_SYMBOL(axp20x_device_remove); MODULE_DESCRIPTION("PMIC MFD core driver for AXP20X"); MODULE_AUTHOR("Carlo Caione <carlo@caione.org>"); diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h index b24c771cebd5..00697c6ad8b0 100644 --- a/include/linux/mfd/axp20x.h +++ b/include/linux/mfd/axp20x.h @@ -396,7 +396,7 @@ enum axp288_irqs { struct axp20x_dev { struct device *dev; - struct i2c_client *i2c_client; + int irq; struct regmap *regmap; struct regmap_irq_chip_data *regmap_irqc; long variant; @@ -462,4 +462,35 @@ static inline int axp20x_read_variable_width(struct regmap *regmap, return result; } +/** + * axp20x_match_device(): Setup axp20x variant related fields + * + * @axp20x: axp20x device to setup (.dev field must be set) + * @dev: device associated with this axp20x device + * + * This lets the axp20x core configure the mfd cells and register maps + * for later use. + */ +int axp20x_match_device(struct axp20x_dev *axp20x); + +/** + * axp20x_device_probe(): Probe a configured axp20x device + * + * @axp20x: axp20x device to probe (must be configured) + * + * This function lets the axp20x core register the axp20x mfd devices + * and irqchip. The axp20x device passed in must be fully configured + * with axp20x_match_device, its irq set, and regmap created. + */ +int axp20x_device_probe(struct axp20x_dev *axp20x); + +/** + * axp20x_device_probe(): Remove a axp20x device + * + * @axp20x: axp20x device to remove + * + * This tells the axp20x core to remove the associated mfd devices + */ +int axp20x_device_remove(struct axp20x_dev *axp20x); + #endif /* __LINUX_MFD_AXP20X_H */
The axp20x driver assumes the device is i2c based. This is not the case with later chips, which use a proprietary 2 wire serial bus by Allwinner called "Reduced Serial Bus". This patch follows the example of mfd/wm831x and splits it into an interface independent core, and an i2c specific glue layer. MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate symbols, allowing the driver to be built as modules. Whitespace and other style errors in the moved i2c specific code have been fixed. Included but unused header files are removed as well. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- Changes since v6: - Drop filenames from file headers --- drivers/mfd/Kconfig | 14 +++--- drivers/mfd/Makefile | 1 + drivers/mfd/axp20x-i2c.c | 104 +++++++++++++++++++++++++++++++++++++++++++++ drivers/mfd/axp20x.c | 90 +++++++-------------------------------- include/linux/mfd/axp20x.h | 33 +++++++++++++- 5 files changed, 161 insertions(+), 81 deletions(-) create mode 100644 drivers/mfd/axp20x-i2c.c