| Message ID | 1453462174-27688-1-git-send-email-nicolas.ferre@atmel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 22/01/2016 at 12:29:34 +0100, Nicolas Ferre wrote : > After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091) > the macb0 interface have difficulties to come back from power saving mode if has > address not explicitely set up. explicitly > As the micrel phy on the board is actually configured to show up at address 1 > we use this explicitly. > Adding the phy node and its real address fixes the issue. Maybe you should add that this also add the proper pinmuxing for the IRQ. > > Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> > --- > arch/arm/boot/dts/at91-sama5d2_xplained.dts | 12 +++++++++++- > 1 file changed, 11 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts > index 77ddff036409..e683856c507c 100644 > --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts > +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts > @@ -114,9 +114,15 @@ > > macb0: ethernet@f8008000 { > pinctrl-names = "default"; > - pinctrl-0 = <&pinctrl_macb0_default>; > + pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>; > phy-mode = "rmii"; > status = "okay"; > + > + ethernet-phy@1 { > + reg = <0x1>; > + interrupt-parent = <&pioA>; > + interrupts = <73 IRQ_TYPE_LEVEL_LOW>; > + }; > }; > > pdmic@f8018000 { > @@ -300,6 +306,10 @@ > bias-disable; > }; > > + pinctrl_macb0_phy_irq: macb0_phy_irq { > + pinmux = <PIN_PC9__GPIO>; > + }; > + > pinctrl_pdmic_default: pdmic_default { > pinmux = <PIN_PB26__PDMIC_DAT>, > <PIN_PB27__PDMIC_CLK>; > -- > 2.1.3 >
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 77ddff036409..e683856c507c 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -114,9 +114,15 @@ macb0: ethernet@f8008000 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_macb0_default>; + pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>; phy-mode = "rmii"; status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + interrupt-parent = <&pioA>; + interrupts = <73 IRQ_TYPE_LEVEL_LOW>; + }; }; pdmic@f8018000 { @@ -300,6 +306,10 @@ bias-disable; }; + pinctrl_macb0_phy_irq: macb0_phy_irq { + pinmux = <PIN_PC9__GPIO>; + }; + pinctrl_pdmic_default: pdmic_default { pinmux = <PIN_PB26__PDMIC_DAT>, <PIN_PB27__PDMIC_CLK>;
After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091) the macb0 interface have difficulties to come back from power saving mode if address not explicitely set up. As the micrel phy on the board is actually configured to show up at address 1 we use this explicitly. Adding the phy node and its real address fixes the issue. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> --- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)