| Message ID | 1458748367-18294-1-git-send-email-zajec5@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 23/03/16 08:52, Rafa? Mi?ecki wrote: > There are few devices that have USB power controlled using GPIO. Linux > USB host driver (bcma-hcd) already supports this by reading vcc-gpio > from DT. Set it properly for all known devices. > > Signed-off-by: Rafa? Mi?ecki <zajec5@gmail.com> Applied to devicetree/next, thanks!
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts index 42dcdfb..fb62ed6 100644 --- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts @@ -139,3 +139,11 @@ &uart0 { status = "okay"; }; + +&usb2 { + vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>; +}; + +&usb3 { + vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>; +}; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts index ca92bba..6bebfa6 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -24,17 +24,6 @@ reg = <0x00000000 0x08000000>; }; - axi@18000000 { - usb3@23000 { - reg = <0x00023000 0x1000>; - - #address-cells = <1>; - #size-cells = <1>; - - vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; - }; - }; - leds { compatible = "gpio-leds"; @@ -97,3 +86,7 @@ &uart0 { status = "okay"; }; + +&usb3 { + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts index 2a92e8d..791d722 100644 --- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts @@ -126,3 +126,8 @@ }; }; }; + + +&usb2 { + vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts index b52927c..ca18151 100644 --- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts @@ -106,3 +106,11 @@ }; }; }; + +&usb2 { + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; +}; + +&usb3 { + vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts index 6c83538..9205c03 100644 --- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts +++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts @@ -109,3 +109,7 @@ status = "okay"; clock-frequency = <125000000>; }; + +&usb3 { + vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi index 65a1309..b3e9d28 100644 --- a/arch/arm/boot/dts/bcm5301x.dtsi +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -207,6 +207,20 @@ gpio-controller; #gpio-cells = <2>; }; + + usb2: usb2@21000 { + reg = <0x00021000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + }; + + usb3: usb3@23000 { + reg = <0x00023000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + }; }; lcpll0: lcpll0@1800c100 {
There are few devices that have USB power controlled using GPIO. Linux USB host driver (bcma-hcd) already supports this by reading vcc-gpio from DT. Set it properly for all known devices. Signed-off-by: Rafa? Mi?ecki <zajec5@gmail.com> --- arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 8 ++++++++ arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 15 ++++----------- arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 5 +++++ arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 8 ++++++++ arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 4 ++++ arch/arm/boot/dts/bcm5301x.dtsi | 14 ++++++++++++++ 6 files changed, 43 insertions(+), 11 deletions(-)