@@ -109,28 +109,33 @@ static const unsigned short bfin_nfc_pin_req[] =
0};
#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-static struct nand_ecclayout bootrom_ecclayout = {
- .eccbytes = 24,
- .eccpos = {
- 0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
- 0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
- 0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
- 0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
- 0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
- 0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
- 0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
- 0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
- },
- .oobfree = {
- { 0x8 * 0 + 3, 5 },
- { 0x8 * 1 + 3, 5 },
- { 0x8 * 2 + 3, 5 },
- { 0x8 * 3 + 3, 5 },
- { 0x8 * 4 + 3, 5 },
- { 0x8 * 5 + 3, 5 },
- { 0x8 * 6 + 3, 5 },
- { 0x8 * 7 + 3, 5 },
- }
+static int bootrom_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ if (section > 7)
+ return -ERANGE;
+
+ oobregion->offset = section * 8;
+ oobregion->length = 3;
+
+ return 0;
+}
+
+static int bootrom_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ if (section > 7)
+ return -ERANGE;
+
+ oobregion->offset = (section * 8) + 3;
+ oobregion->length = 5;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops bootrom_ooblayout_ops = {
+ .ecc = bootrom_ooblayout_ecc,
+ .free = bootrom_ooblayout_free,
};
#endif
@@ -800,7 +805,7 @@ static int bf5xx_nand_probe(struct platform_device *pdev)
/* setup hardware ECC data struct */
if (hardware_ecc) {
#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
- chip->ecc.layout = &bootrom_ecclayout;
+ mtd_set_ooblayout(mtd, &bootrom_ooblayout_ops);
#endif
chip->read_buf = bf5xx_nand_dma_read_buf;
chip->write_buf = bf5xx_nand_dma_write_buf;
Implementing the mtd_ooblayout_ops interface is the new way of exposing ECC/OOB layout to MTD users. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> --- drivers/mtd/nand/bf5xx_nand.c | 51 ++++++++++++++++++++++++------------------- 1 file changed, 28 insertions(+), 23 deletions(-)