@@ -1374,13 +1374,41 @@ static void denali_hw_init(struct denali_nand_info *denali)
* correction
*/
#define ECC_8BITS 14
-static struct nand_ecclayout nand_8bit_oob = {
- .eccbytes = 14,
-};
-
#define ECC_15BITS 26
-static struct nand_ecclayout nand_15bit_oob = {
- .eccbytes = 26,
+
+static int denali_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = denali->bbtskipbytes;
+ oobregion->length = chip->ecc.total;
+
+ return 0;
+}
+
+static int denali_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = chip->ecc.total + denali->bbtskipbytes;
+ oobregion->length = mtd->oobsize - oobregion->offset;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops denali_ooblayout_ops = {
+ .ecc = denali_ooblayout_ecc,
+ .free = denali_ooblayout_free,
};
static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
@@ -1561,7 +1589,6 @@ int denali_init(struct denali_nand_info *denali)
ECC_SECTOR_SIZE)))) {
/* if MLC OOB size is large enough, use 15bit ECC*/
denali->nand.ecc.strength = 15;
- denali->nand.ecc.layout = &nand_15bit_oob;
denali->nand.ecc.bytes = ECC_15BITS;
iowrite32(15, denali->flash_reg + ECC_CORRECTION);
} else if (mtd->oobsize < (denali->bbtskipbytes +
@@ -1571,20 +1598,13 @@ int denali_init(struct denali_nand_info *denali)
goto failed_req_irq;
} else {
denali->nand.ecc.strength = 8;
- denali->nand.ecc.layout = &nand_8bit_oob;
denali->nand.ecc.bytes = ECC_8BITS;
iowrite32(8, denali->flash_reg + ECC_CORRECTION);
}
+ mtd_set_ooblayout(mtd, &denali_ooblayout_ops);
denali->nand.ecc.bytes *= denali->devnum;
denali->nand.ecc.strength *= denali->devnum;
- denali->nand.ecc.layout->eccbytes *=
- mtd->writesize / ECC_SECTOR_SIZE;
- denali->nand.ecc.layout->oobfree[0].offset =
- denali->bbtskipbytes + denali->nand.ecc.layout->eccbytes;
- denali->nand.ecc.layout->oobfree[0].length =
- mtd->oobsize - denali->nand.ecc.layout->eccbytes -
- denali->bbtskipbytes;
/*
* Let driver know the total blocks number and how many blocks
Implementing the mtd_ooblayout_ops interface is the new way of exposing ECC/OOB layout to MTD users. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> --- drivers/mtd/nand/denali.c | 50 +++++++++++++++++++++++++++++++++-------------- 1 file changed, 35 insertions(+), 15 deletions(-)