@@ -2,7 +2,9 @@ MOXA ART timer
Required properties:
-- compatible : Must be "moxa,moxart-timer"
+- compatible : Must be one of:
+ - "moxa,moxart-timer"
+ - "aspeed,ast2400-timer"
- reg : Should contain registers location and length
- interrupts : Should contain the timer interrupt number
- clocks : Should contain phandle for the clock that drives the counter
@@ -56,6 +56,23 @@
#define MOXART_TIMER1_ENABLE (MOXART_CR_2_ENABLE | MOXART_CR_1_ENABLE)
#define MOXART_TIMER1_DISABLE (MOXART_CR_2_ENABLE)
+/*
+ * The ASpeed variant of the IP block has a different layout
+ * for the control register
+ */
+#define ASPEED_CR_1_ENABLE BIT(0)
+#define ASPEED_CR_1_CLOCK BIT(1)
+#define ASPEED_CR_1_INT BIT(2)
+#define ASPEED_CR_2_ENABLE BIT(4)
+#define ASPEED_CR_2_CLOCK BIT(5)
+#define ASPEED_CR_2_INT BIT(6)
+#define ASPEED_CR_3_ENABLE BIT(8)
+#define ASPEED_CR_3_CLOCK BIT(9)
+#define ASPEED_CR_3_INT BIT(10)
+
+#define ASPEED_TIMER1_ENABLE (ASPEED_CR_2_ENABLE | ASPEED_CR_1_ENABLE)
+#define ASPEED_TIMER1_DISABLE (ASPEED_CR_2_ENABLE)
+
struct moxart_timer {
void __iomem *base;
unsigned int t1_disable_val;
@@ -159,6 +176,9 @@ static void __init moxart_timer_init(struct device_node *node)
if (of_device_is_compatible(node, "moxa,moxart-timer")) {
timer->t1_enable_val = MOXART_TIMER1_ENABLE;
timer->t1_disable_val = MOXART_TIMER1_DISABLE;
+ } else if (of_device_is_compatible(node, "aspeed,ast2400-timer")) {
+ timer->t1_enable_val = ASPEED_TIMER1_ENABLE;
+ timer->t1_disable_val = ASPEED_TIMER1_DISABLE;
} else
panic("%s: unknown platform\n", node->full_name);
@@ -189,6 +209,17 @@ static void __init moxart_timer_init(struct device_node *node)
if (ret)
panic("%s: setup_irq failed\n", node->full_name);
+ /* Clear match registers */
+ writel(0, timer->base + TIMER1_BASE + REG_MATCH1);
+ writel(0, timer->base + TIMER1_BASE + REG_MATCH2);
+ writel(0, timer->base + TIMER2_BASE + REG_MATCH1);
+ writel(0, timer->base + TIMER2_BASE + REG_MATCH2);
+
+ /*
+ * Start timer 2 rolling as our main wall clock source, keep timer 1
+ * disabled
+ */
+ writel(0, timer->base + TIMER_CR);
writel(~0, timer->base + TIMER2_BASE + REG_LOAD);
writel(timer->t1_disable_val, timer->base + TIMER_CR);
@@ -201,3 +232,4 @@ static void __init moxart_timer_init(struct device_node *node)
clockevents_config_and_register(&timer->clkevt, pclk, 0x4, 0xfffffffe);
}
CLOCKSOURCE_OF_DECLARE(moxart, "moxa,moxart-timer", moxart_timer_init);
+CLOCKSOURCE_OF_DECLARE(aspeed, "aspeed,ast2400-timer", moxart_timer_init);
The Aspeed SoC has timer IP with a very similar register layout to the moxart timer. This patch adds support for the fourth and fifth gen aspeed SoCs, and has been tested on the ast2400 and ast2500. Signed-off-by: Joel Stanley <joel@jms.id.au> --- .../bindings/timer/moxa,moxart-timer.txt | 4 ++- drivers/clocksource/moxart_timer.c | 32 ++++++++++++++++++++++ 2 files changed, 35 insertions(+), 1 deletion(-)