diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt
new file mode 100644
index 0000000..2fe9b5b
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt
@@ -0,0 +1,136 @@
+* Device tree bindings for Atmel EBI
+
+The External Bus Interface (EBI) controller is a bus where you can connect
+asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
+The EBI provides a glue-less interface to asynchronous memories through the SMC
+(Static Memory Controller).
+
+Required properties:
+
+- compatible:		"atmel,at91sam9260-ebi"
+			"atmel,at91sam9261-ebi"
+			"atmel,at91sam9263-ebi0"
+			"atmel,at91sam9263-ebi1"
+			"atmel,at91sam9rl-ebi"
+			"atmel,at91sam9g45-ebi"
+			"atmel,at91sam9x5-ebi"
+			"atmel,sama5d3-ebi"
+
+- reg:			Contains offset/length value for EBI memory mapping.
+			This property might contain several entries if the EBI
+			memory range is not contiguous
+
+- #address-cells:	Must be 2.
+			The first cell encodes the CS.
+			The second cell encode the offset into the CS memory
+			range.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Encodes CS to memory region association.
+
+- clocks:		Clock feeding the EBI controller.
+			See clock-bindings.txt
+
+Children device nodes are representing device connected to the EBI bus.
+
+Required device node properties:
+
+- #reg:			Contains the chip-select id, the offset and the length
+			of the memory region requested by the device.
+
+EBI bus configuration will be defined directly in the device subnode.
+
+Optional EBI/SMC properties:
+
+- atmel,smc-bus-width:		width of the asynchronous device's data bus
+				8, 16 or 32.
+				Default to 8 when undefined.
+
+- atmel,smc-byte-access-type	"write" or "select" (see Atmel datasheet).
+				Default to "select" when undefined.
+
+- atmel,smc-read-mode		"nrd" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-write-mode		"nwe" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-exnw-mode		"disabled", "frozen" or "ready".
+				Default to "disabled" when undefined.
+
+- atmel,smc-page-mode		enable page mode if present. The provided value
+				defines the page size (supported values: 4, 8,
+				16 and 32).
+
+- atmel,smc-tdf-mode:		"normal" or "optimized". When set to
+				"optimized" the data float time is optimized
+				depending on the next device being accessed
+				(next device setup time is subtracted to the
+				current device data float time).
+				Default to "normal" when undefined.
+
+If at least one atmel,smc- property is defined the following SMC timing
+properties become mandatory. In the other hand, if none of the atmel,smc-
+properties are specified, we assume that the EBI bus configuration will be
+handled by the sub-device driver, and none of those properties should be
+defined.
+
+All the timings are expressed in nanoseconds (see Atmel datasheet for a full
+description).
+
+- atmel,smc-ncs-rd-setup-ns
+- atmel,smc-nrd-setup-ns
+- atmel,smc-ncs-wr-setup-ns
+- atmel,smc-nwe-setup-ns
+- atmel,smc-ncs-rd-pulse-ns
+- atmel,smc-nrd-pulse-ns
+- atmel,smc-ncs-wr-pulse-ns
+- atmel,smc-nwe-pulse-ns
+- atmel,smc-nwe-cycle-ns
+- atmel,smc-nrd-cycle-ns
+- atmel,smc-tdf-ns
+
+Example:
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		atmel,matrix = <&matrix>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ebi_addr>;
+
+		nor: flash@0,0 {
+			compatible = "cfi-flash";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x0 0x0 0x1000000>;
+			bank-width = <2>;
+
+			atmel,smc-read-mode = "nrd";
+			atmel,smc-write-mode = "nwe";
+			atmel,smc-bus-width = <16>;
+			atmel,smc-ncs-rd-setup-ns = <0>;
+			atmel,smc-ncs-wr-setup-ns = <0>;
+			atmel,smc-nwe-setup-ns = <8>;
+			atmel,smc-nrd-setup-ns = <16>;
+			atmel,smc-ncs-rd-pulse-ns = <84>;
+			atmel,smc-ncs-wr-pulse-ns = <84>;
+			atmel,smc-nrd-pulse-ns = <76>;
+			atmel,smc-nwe-pulse-ns = <76>;
+			atmel,smc-nrd-cycle-ns = <107>;
+			atmel,smc-nwe-cycle-ns = <84>;
+			atmel,smc-tdf-ns = <16>;
+		};
+	};
+
