| Message ID | 1469755528-8413-8-git-send-email-wenyou.yang@atmel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, Jul 29, 2016 at 09:25:28AM +0800, Wenyou Yang wrote: > Due the driver improvements, update the properties, > - Remove "active-semi,check-battery-temperature" property. > - Add the properties, "active-semi,irq_gpio" > and "active-semi,lbo-gpios". > > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> > --- > > Changes in v3: None > Changes in v2: None > > Documentation/devicetree/bindings/power/act8945a-charger.txt | 6 ++++-- > 1 file changed, 4 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt b/Documentation/devicetree/bindings/power/act8945a-charger.txt > index bea254c..d7cf05b 100644 > --- a/Documentation/devicetree/bindings/power/act8945a-charger.txt > +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt > @@ -4,10 +4,12 @@ Required properties: > - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. > - active-semi,chglev-gpios: charge current level phandle with args > as described in ../gpio/gpio.txt. > + - active-semi,irq_gpios: specify the charger interrupt input phanle > + with args as as described in ../gpio/gpio.txt. As I said in v2, this should be an interrupt property instead. > + - active-semi,lbo-gpios: specify the low battery voltage detect phandle > + with args as as described in ../gpio/gpio.txt. Maybe this one too. > > Optional properties: > - - active-semi,check-battery-temperature: boolean to check the battery > - temperature or not. > - active-semi,input-voltage-threshold-microvolt: unit: mV; > Specifies the charger's input over-voltage threshold value; > The value can be: 6600, 7000, 7500, 8000; default: 6600 > -- > 2.7.4 >
Hi Rob, > -----Original Message----- > From: Rob Herring [mailto:robh@kernel.org] > Sent: 2016年7月30日 5:40 > To: Wenyou Yang <wenyou.yang@atmel.com> > Cc: Sebastian Reichel <sre@kernel.org>; Dmitry Eremin-Solenikov > <dbaryshkov@gmail.com>; David Woodhouse <dwmw2@infradead.org>; Pawel > Moll <pawel.moll@arm.com>; Mark Brown <broonie@kernel.org>; Ian Campbell > <ijc+devicetree@hellion.org.uk>; Kumar Gala <galak@codeaurora.org>; linux- > kernel@vger.kernel.org; devicetree@vger.kernel.org; linux-arm- > kernel@lists.infradead.org; Nicolas Ferre <nicolas.ferre@atmel.com>; linux- > pm@vger.kernel.org > Subject: Re: [PATCH v3 7/7] doc: bindings: act8945a-charger: Update properties > > On Fri, Jul 29, 2016 at 09:25:28AM +0800, Wenyou Yang wrote: > > Due the driver improvements, update the properties, > > - Remove "active-semi,check-battery-temperature" property. > > - Add the properties, "active-semi,irq_gpio" > > and "active-semi,lbo-gpios". > > > > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> > > --- > > > > Changes in v3: None > > Changes in v2: None > > > > Documentation/devicetree/bindings/power/act8945a-charger.txt | 6 ++++-- > > 1 file changed, 4 insertions(+), 2 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt > b/Documentation/devicetree/bindings/power/act8945a-charger.txt > > index bea254c..d7cf05b 100644 > > --- a/Documentation/devicetree/bindings/power/act8945a-charger.txt > > +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt > > @@ -4,10 +4,12 @@ Required properties: > > - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. > > - active-semi,chglev-gpios: charge current level phandle with args > > as described in ../gpio/gpio.txt. > > + - active-semi,irq_gpios: specify the charger interrupt input phanle > > + with args as as described in ../gpio/gpio.txt. > > As I said in v2, this should be an interrupt property instead. Sorry for forgetting to change. Accepted, will be in next version. Thanks. > > > + - active-semi,lbo-gpios: specify the low battery voltage detect phandle > > + with args as as described in ../gpio/gpio.txt. > > Maybe this one too. The capacity level function need to read this pin level, so this one should not use "interrupts" property. > > > > > Optional properties: > > - - active-semi,check-battery-temperature: boolean to check the battery > > - temperature or not. > > - active-semi,input-voltage-threshold-microvolt: unit: mV; > > Specifies the charger's input over-voltage threshold value; > > The value can be: 6600, 7000, 7500, 8000; default: 6600 > > -- > > 2.7.4 > > Best Regards, Wenyou Yang
diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt b/Documentation/devicetree/bindings/power/act8945a-charger.txt index bea254c..d7cf05b 100644 --- a/Documentation/devicetree/bindings/power/act8945a-charger.txt +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt @@ -4,10 +4,12 @@ Required properties: - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. - active-semi,chglev-gpios: charge current level phandle with args as described in ../gpio/gpio.txt. + - active-semi,irq_gpios: specify the charger interrupt input phanle + with args as as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. Optional properties: - - active-semi,check-battery-temperature: boolean to check the battery - temperature or not. - active-semi,input-voltage-threshold-microvolt: unit: mV; Specifies the charger's input over-voltage threshold value; The value can be: 6600, 7000, 7500, 8000; default: 6600
Due the driver improvements, update the properties, - Remove "active-semi,check-battery-temperature" property. - Add the properties, "active-semi,irq_gpio" and "active-semi,lbo-gpios". Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> --- Changes in v3: None Changes in v2: None Documentation/devicetree/bindings/power/act8945a-charger.txt | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)