| Message ID | 1473957763-30629-8-git-send-email-alexandre.torgue@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, Sep 15, 2016 at 06:42:39PM +0200, Alexandre TORGUE wrote: > Signed-off-by: Gerald Baeza <gerald.baeza@st.com> > Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Squash this with the other binding patch. You are describing the h/w block, do so completely. > > diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt > index 75b1400..85ec5f2 100644 > --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt > +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt > @@ -12,6 +12,8 @@ stm32(f4) or stm32f7. > Optional properties: > - pinctrl: The reference on the pins configuration > - st,hw-flow-ctrl: bool flag to enable hardware flow control. > +- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt > +- dma-names: "rx" and/or "tx" > > Examples: > usart4: serial@40004c00 { > @@ -32,3 +34,13 @@ usart2: serial@40004400 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>; > }; > + > +usart1: serial@40011000 { > + compatible = "st,stm32-usart", "st,stm32-uart"; > + reg = <0x40011000 0x400>; > + interrupts = <37>; > + clocks = <&rcc 0 164>; > + dmas = <&dma2 2 4 0x414 0x0>, > + <&dma2 7 4 0x414 0x0>; > + dma-names = "rx", "tx"; > +}; > -- > 1.9.1 >
diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt index 75b1400..85ec5f2 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -12,6 +12,8 @@ stm32(f4) or stm32f7. Optional properties: - pinctrl: The reference on the pins configuration - st,hw-flow-ctrl: bool flag to enable hardware flow control. +- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt +- dma-names: "rx" and/or "tx" Examples: usart4: serial@40004c00 { @@ -32,3 +34,13 @@ usart2: serial@40004400 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>; }; + +usart1: serial@40011000 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&rcc 0 164>; + dmas = <&dma2 2 4 0x414 0x0>, + <&dma2 7 4 0x414 0x0>; + dma-names = "rx", "tx"; +};