@@ -26,7 +26,6 @@
#include <linux/platform_data/mtd-davinci.h>
#include <linux/platform_data/mtd-davinci-aemif.h>
#include <linux/platform_data/spi-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -106,30 +105,8 @@ static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
static __init void da830_evm_usb_init(void)
{
- u32 cfgchip2;
int ret;
- /*
- * Set up USB clock/mode in the CFGCHIP2 register.
- * FYI: CFGCHIP2 is 0x0000ef00 initially.
- */
- cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- /*
- * We have to override VBUS/ID signals when MUSB is configured into the
- * host-only mode -- ID pin will float if no cable is connected, so the
- * controller won't be able to drive VBUS thinking that it's a B-device.
- * Otherwise, we want to use the OTG mode and enable VBUS comparators.
- */
- cfgchip2 &= ~CFGCHIP2_OTGMODE;
-#ifdef CONFIG_USB_MUSB_HOST
- cfgchip2 |= CFGCHIP2_FORCE_HOST;
-#else
- cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
-#endif
-
- __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
/* USB_REFCLKIN is not used. */
ret = da8xx_register_usb20_phy_clk(false);
if (ret)
@@ -141,6 +118,11 @@ static __init void da830_evm_usb_init(void)
pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
__func__, ret);
+ ret = da8xx_register_usb_phy();
+ if (ret)
+ pr_warn("%s: USB PHY registration failed: %d\n",
+ __func__, ret);
+
ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
if (ret)
pr_warn("%s: USB 2.0 PinMux setup failed: %d\n", __func__, ret);
@@ -260,6 +260,11 @@ static __init void omapl138_hawk_usb_init(void)
pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
__func__, ret);
+ ret = da8xx_register_usb_phy();
+ if (ret)
+ pr_warn("%s: USB PHY registration failed: %d\n",
+ __func__, ret);
+
ret = gpio_request_one(DA850_USB1_VBUS_PIN,
GPIOF_DIR_OUT, "USB1 VBUS");
if (ret < 0) {
@@ -92,6 +92,7 @@ int da8xx_register_watchdog(void);
int da8xx_register_usb_refclkin(int rate);
int da8xx_register_usb20_phy_clk(bool use_usb_refclkin);
int da8xx_register_usb11_phy_clk(bool use_usb_refclkin);
+int da8xx_register_usb_phy(void);
int da8xx_register_usb20(unsigned mA, unsigned potpgt);
int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
int da8xx_register_emac(void);
@@ -7,6 +7,7 @@
#include <linux/platform_data/usb-davinci.h>
#include <linux/platform_device.h>
#include <linux/mfd/da8xx-cfgchip.h>
+#include <linux/phy/phy.h>
#include <linux/usb/musb.h>
#include <mach/clock.h>
@@ -243,6 +244,16 @@ int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
return ret;
}
+static struct platform_device da8xx_usb_phy = {
+ .name = "da8xx-usb-phy",
+ .id = -1,
+};
+
+int __init da8xx_register_usb_phy(void)
+{
+ return platform_device_register(&da8xx_usb_phy);
+}
+
#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
static struct musb_hdrc_config musb_config = {
There is now a proper phy driver for the DA8xx SoC USB PHY. This adds the platform device declarations needed to use it. Signed-off-by: David Lechner <david@lechnology.com> --- da8xx-usb-phy device id is changed to -1 since there is only one da8xx-usb-phy device. arch/arm/mach-davinci/board-da830-evm.c | 28 +++++----------------------- arch/arm/mach-davinci/board-omapl138-hawk.c | 5 +++++ arch/arm/mach-davinci/include/mach/da8xx.h | 1 + arch/arm/mach-davinci/usb-da8xx.c | 11 +++++++++++ 4 files changed, 22 insertions(+), 23 deletions(-)