@@ -14,12 +14,21 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/bcma/bcma.h>
+#include <linux/brcmphy.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include "bgmac.h"
+#define NICPM_IOMUX_CTRL 0x00000008
+
+#define NICPM_IOMUX_CTRL_INIT_VAL 0x3196e000
+#define NICPM_IOMUX_CTRL_SPD_SHIFT 10
+#define NICPM_IOMUX_CTRL_SPD_10M 0
+#define NICPM_IOMUX_CTRL_SPD_100M 1
+#define NICPM_IOMUX_CTRL_SPD_1000M 2
+
static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
{
return readl(bgmac->plat.base + offset);
@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
WARN_ON(1);
}
+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
+{
+ struct bgmac *bgmac = netdev_priv(net_dev);
+ u32 val;
+
+ if (!bgmac->plat.nicpm_base)
+ return;
+
+ val = NICPM_IOMUX_CTRL_INIT_VAL;
+ switch (bgmac->net_dev->phydev->speed) {
+ default:
+ pr_err("Unsupported speed. Defaulting to 1000Mb\n");
+ case SPEED_1000:
+ val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ case SPEED_100:
+ val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ case SPEED_10:
+ val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ }
+
+ writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
+
+ bgmac_adjust_link(bgmac->net_dev);
+}
+
static int platform_phy_connect(struct bgmac *bgmac)
{
struct phy_device *phy_dev;
- phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
- bgmac_adjust_link);
+ if (bgmac->plat.nicpm_base)
+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+ bgmac->dev->of_node,
+ bgmac_nicpm_speed_set);
+ else
+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+ bgmac->dev->of_node,
+ bgmac_adjust_link);
if (!phy_dev) {
dev_err(bgmac->dev, "Phy connect failed\n");
return -ENODEV;
@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
if (IS_ERR(bgmac->plat.idm_base))
return PTR_ERR(bgmac->plat.idm_base);
+ regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
+ if (regs) {
+ bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
+ regs);
+ if (IS_ERR(bgmac->plat.nicpm_base))
+ return PTR_ERR(bgmac->plat.nicpm_base);
+ }
+
bgmac->read = platform_bgmac_read;
bgmac->write = platform_bgmac_write;
bgmac->idm_read = platform_bgmac_idm_read;
@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
static const struct of_device_id bgmac_of_enet_match[] = {
{.compatible = "brcm,amac",},
{.compatible = "brcm,nsp-amac",},
+ {.compatible = "brcm,ns2-amac",},
{},
};
@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
static void bgmac_chip_init(struct bgmac *bgmac)
{
+ /* Clear any erroneously pending interrupts */
+ bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
+
/* 1 interrupt per received frame */
bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
@@ -463,6 +463,7 @@ struct bgmac {
struct {
void *base;
void *idm_base;
+ void *nicpm_base;
} plat;
struct {
struct bcma_device *core;
Add support for the variant of amac hardware present in the Broadcom Northstar2 based SoCs. Northstar2 requires an additional register to be configured with the port speed/duplexity (NICPM). This can be added to the link callback to hide it from the instances that do not use this. Also, clearing of the pending interrupts on init is required due to observed issues on some platforms. Signed-off-by: Jon Mason <jon.mason@broadcom.com> --- drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++- drivers/net/ethernet/broadcom/bgmac.c | 3 ++ drivers/net/ethernet/broadcom/bgmac.h | 1 + 3 files changed, 58 insertions(+), 2 deletions(-)