| Message ID | 1478155149-28527-5-git-send-email-cw00.choi@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Chanwoo, Tested-by: Andi Shyti <andi.shyti@samsung.com> Andi On Thu, Nov 03, 2016 at 03:39:08PM +0900, Chanwoo Choi wrote: > This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board. > This board fully support the all things for mobile target. > > This patch supports the following devices: > 1. basic SoC > - Initial booting for Samsung Exynos5433 SoC > - DRAM LPDDR3 (3GB) > - eMMC (32GB) > - ARM architecture timer > > 2. power management devices > - Sasmung S2MPS13 PMIC for the power supply > - CPUFREQ for big.LITTLE cores > - TMU for big.LITTLE cores and GPU > - ADC with thermistor to measure the temperature of AP/Battery/Charger > - Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator) > > 3. sound devices > - I2S for sound bus > - LPASS for sound power control > - Wolfson WM5110 for sound codec > - Maxim MAX98504 for speaker amplifier > - TM2 ASoC Machine device driver node > > 3. display devices > - DECON, DSI and MIC for the panel output > > 4. usb devices > - USB 3.0 DRD (Dual Role Device) > - USB 3.0 Host controller > > 5. storage devices > - MSHC (Mobile Storage Host Controller) for eMMC device > > 6. misc devices > - gpio-keys (power, volume up/down, home key) > - PWM (Pulse Width Modulation Timer) > > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> > Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> > Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> > Signed-off-by: Inki Dae <inki.dae@samsung.com> > Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com> > Signed-off-by: Beomho Seo <beomho.seo@samsung.com> > Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Inha Song <ideal.song@samsung.com> > Signed-off-by: Ingi kim <ingi2.kim@samsung.com> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> > --- > .../bindings/arm/samsung/samsung-boards.txt | 1 + > arch/arm64/boot/dts/exynos/Makefile | 4 +- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 974 +++++++++++++++++++++ > 3 files changed, 978 insertions(+), 1 deletion(-) > create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > > diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt > index 0ea7f14ef294..339af8b9cdc5 100644 > --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt > +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt > @@ -15,6 +15,7 @@ Required root node properties: > - "samsung,xyref5260" - for Exynos5260-based Samsung board. > - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. > - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. > + - "samsung,tm2" - for Exynos5433-based Samsung TM2 board. > - "samsung,sd5v1" - for Exynos5440-based Samsung board. > - "samsung,ssdk5440" - for Exynos5440-based Samsung board. > > diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile > index 50c9b9383cfa..947c750acba1 100644 > --- a/arch/arm64/boot/dts/exynos/Makefile > +++ b/arch/arm64/boot/dts/exynos/Makefile > @@ -1,4 +1,6 @@ > -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb > +dtb-$(CONFIG_ARCH_EXYNOS) += \ > + exynos5433-tm2.dtb \ > + exynos7-espresso.dtb > > always := $(dtb-y) > subdir-y := $(dts-dirs) > diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > new file mode 100644 > index 000000000000..9ea3f32bae9e > --- /dev/null > +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts > @@ -0,0 +1,974 @@ > +/* > + * SAMSUNG Exynos5433 TM2 board device tree source > + * > + * Copyright (c) 2016 Samsung Electronics Co., Ltd. > + * > + * Device tree source file for Samsung's TM2 board which is based on > + * Samsung Exynos5433 SoC. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +/dts-v1/; > +#include "exynos5433.dtsi" > +#include <dt-bindings/clock/samsung,s2mps11.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/irq.h> > + > +/ { > + model = "Samsung TM2 board"; > + compatible = "samsung,tm2", "samsung,exynos5433"; > + > + aliases { > + pinctrl0 = &pinctrl_alive; > + pinctrl1 = &pinctrl_aud; > + pinctrl2 = &pinctrl_cpif; > + pinctrl3 = &pinctrl_ese; > + pinctrl4 = &pinctrl_finger; > + pinctrl5 = &pinctrl_fsys; > + pinctrl6 = &pinctrl_imem; > + pinctrl7 = &pinctrl_nfc; > + pinctrl8 = &pinctrl_peric; > + pinctrl9 = &pinctrl_touch; > + serial0 = &serial_0; > + serial1 = &serial_1; > + serial2 = &serial_2; > + serial3 = &serial_3; > + spi0 = &spi_0; > + spi1 = &spi_1; > + spi2 = &spi_2; > + spi3 = &spi_3; > + spi4 = &spi_4; > + }; > + > + chosen { > + stdout-path = &serial_1; > + }; > + > + memory@20000000 { > + device_type = "memory"; > + reg = <0x0 0x20000000 0x0 0xc0000000>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + power-key { > + gpios = <&gpa2 7 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_POWER>; > + label = "power key"; > + debounce-interval = <10>; > + }; > + > + volume-up-key { > + gpios = <&gpa2 0 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + label = "volume-up key"; > + debounce-interval = <10>; > + }; > + > + volume-down-key { > + gpios = <&gpa2 1 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEDOWN>; > + label = "volume-down key"; > + debounce-interval = <10>; > + }; > + > + homepage-key { > + gpios = <&gpa0 3 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_MENU>; > + label = "homepage key"; > + debounce-interval = <10>; > + }; > + }; > + > + i2c_max98504: i2c-gpio-0 { > + compatible = "i2c-gpio"; > + gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */ > + &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + max98504: max98504@31 { > + compatible = "maxim,max98504"; > + reg = <0x31>; > + maxim,rx-path = <1>; > + maxim,tx-path = <1>; > + maxim,tx-channel-mask = <3>; > + maxim,tx-channel-source = <2>; > + }; > + }; > + > + sound { > + compatible = "samsung,tm2-audio"; > + audio-codec = <&wm5110>; > + i2s-controller = <&i2s0>; > + audio-amplifier = <&max98504>; > + mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>; > + model = "wm5110"; > + samsung,audio-routing = > + /* Headphone */ > + "HP", "HPOUT1L", > + "HP", "HPOUT1R", > + > + /* Speaker */ > + "SPK", "SPKOUT", > + "SPKOUT", "HPOUT2L", > + "SPKOUT", "HPOUT2R", > + > + /* Receiver */ > + "RCV", "HPOUT3L", > + "RCV", "HPOUT3R"; > + status = "okay"; > + }; > +}; > + > +&adc { > + vdd-supply = <&ldo3_reg>; > + status = "okay"; > + > + thermistor-ap { > + compatible = "murata,ncp03wf104"; > + pullup-uv = <1800000>; > + pullup-ohm = <100000>; > + pulldown-ohm = <0>; > + io-channels = <&adc 0>; > + }; > + > + thermistor-battery { > + compatible = "murata,ncp03wf104"; > + pullup-uv = <1800000>; > + pullup-ohm = <100000>; > + pulldown-ohm = <0>; > + io-channels = <&adc 1>; > + #thermal-sensor-cells = <0>; > + }; > + > + thermistor-charger { > + compatible = "murata,ncp03wf104"; > + pullup-uv = <1800000>; > + pullup-ohm = <100000>; > + pulldown-ohm = <0>; > + io-channels = <&adc 2>; > + }; > +}; > + > +&cpu0 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&cpu4 { > + cpu-supply = <&buck2_reg>; > +}; > + > +&decon { > + status = "okay"; > + > + i80-if-timings { > + }; > +}; > + > +&dsi { > + status = "okay"; > + vddcore-supply = <&ldo6_reg>; > + vddio-supply = <&ldo7_reg>; > + samsung,pll-clock-frequency = <24000000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&te_irq>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <1>; > + > + dsi_out: endpoint { > + samsung,burst-clock-frequency = <512000000>; > + samsung,esc-clock-frequency = <16000000>; > + }; > + }; > + }; > +}; > + > +&hsi2c_0 { > + status = "okay"; > + clock-frequency = <2500000>; > + > + s2mps13-pmic@66 { > + compatible = "samsung,s2mps13-pmic"; > + interrupt-parent = <&gpa0>; > + interrupts = <7 IRQ_TYPE_NONE>; > + reg = <0x66>; > + samsung,s2mps11-wrstbi-ground; > + > + s2mps13_osc: clocks { > + compatible = "samsung,s2mps13-clk"; > + #clock-cells = <1>; > + clock-output-names = "s2mps13_ap", "s2mps13_cp", > + "s2mps13_bt"; > + }; > + > + regulators { > + ldo1_reg: LDO1 { > + regulator-name = "VDD_ALIVE_0.9V_AP"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-always-on; > + }; > + > + ldo2_reg: LDO2 { > + regulator-name = "VDDQ_MMC2_2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo3_reg: LDO3 { > + regulator-name = "VDD1_E_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + ldo4_reg: LDO4 { > + regulator-name = "VDD10_MIF_PLL_1.0V_AP"; > + regulator-min-microvolt = <1300000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo5_reg: LDO5 { > + regulator-name = "VDD10_DPLL_1.0V_AP"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo6_reg: LDO6 { > + regulator-name = "VDD10_MIPI2L_1.0V_AP"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo7_reg: LDO7 { > + regulator-name = "VDD18_MIPI2L_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo8_reg: LDO8 { > + regulator-name = "VDD18_LLI_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo9_reg: LDO9 { > + regulator-name = "VDD18_ABB_ETC_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo10_reg: LDO10 { > + regulator-name = "VDD33_USB30_3.0V_AP"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo11_reg: LDO11 { > + regulator-name = "VDD_INT_M_1.0V_AP"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo12_reg: LDO12 { > + regulator-name = "VDD_KFC_M_1.1V_AP"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + }; > + > + ldo13_reg: LDO13 { > + regulator-name = "VDD_G3D_M_0.95V_AP"; > + regulator-min-microvolt = <950000>; > + regulator-max-microvolt = <950000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo14_reg: LDO14 { > + regulator-name = "VDDQ_M1_LDO_1.2V_AP"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo15_reg: LDO15 { > + regulator-name = "VDDQ_M2_LDO_1.2V_AP"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo16_reg: LDO16 { > + regulator-name = "VDDQ_EFUSE"; > + regulator-min-microvolt = <1400000>; > + regulator-max-microvolt = <3400000>; > + regulator-always-on; > + }; > + > + ldo17_reg: LDO17 { > + regulator-name = "V_TFLASH_2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + ldo18_reg: LDO18 { > + regulator-name = "V_CODEC_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo19_reg: LDO19 { > + regulator-name = "VDDA_1.8V_COMP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + ldo20_reg: LDO20 { > + regulator-name = "VCC_2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > + }; > + > + ldo21_reg: LDO21 { > + regulator-name = "VT_CAM_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo22_reg: LDO22 { > + regulator-name = "CAM_IO_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo23_reg: LDO23 { > + regulator-name = "CAM_SEN_CORE_1.2V_AP"; > + regulator-min-microvolt = <1050000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + ldo24_reg: LDO24 { > + regulator-name = "VT_CAM_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + ldo25_reg: LDO25 { > + regulator-name = "CAM_SEN_A2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + ldo26_reg: LDO26 { > + regulator-name = "CAM_AF_2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + ldo27_reg: LDO27 { > + regulator-name = "VCC_3.0V_LCD_AP"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + }; > + > + ldo28_reg: LDO28 { > + regulator-name = "VCC_1.8V_LCD_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo29_reg: LDO29 { > + regulator-name = "VT_CAM_2.8V"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + }; > + > + ldo30_reg: LDO30 { > + regulator-name = "TSP_AVDD_3.3V_AP"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + ldo31_reg: LDO31 { > + regulator-name = "TSP_VDD_1.85V_AP"; > + regulator-min-microvolt = <1850000>; > + regulator-max-microvolt = <1850000>; > + }; > + > + ldo32_reg: LDO32 { > + regulator-name = "VTOUCH_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo33_reg: LDO33 { > + regulator-name = "VTOUCH_LED_3.3V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <3300000>; > + regulator-ramp-delay = <12500>; > + }; > + > + ldo34_reg: LDO34 { > + regulator-name = "VCC_1.8V_MHL_AP"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + ldo35_reg: LDO35 { > + regulator-name = "OIS_VM_2.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + ldo36_reg: LDO36 { > + regulator-name = "VSIL_1.0V"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + > + ldo37_reg: LDO37 { > + regulator-name = "VF_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo38_reg: LDO38 { > + regulator-name = "VCC_3.0V_MOTOR_AP"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + }; > + > + ldo39_reg: LDO39 { > + regulator-name = "V_HRM_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + ldo40_reg: LDO40 { > + regulator-name = "V_HRM_3.3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + buck1_reg: BUCK1 { > + regulator-name = "VDD_MIF_0.9V_AP"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck2_reg: BUCK2 { > + regulator-name = "VDD_EGL_1.0V_AP"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck3_reg: BUCK3 { > + regulator-name = "VDD_KFC_1.0V_AP"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck4_reg: BUCK4 { > + regulator-name = "VDD_INT_0.95V_AP"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck5_reg: BUCK5 { > + regulator-name = "VDD_DISP_CAM0_0.9V_AP"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck6_reg: BUCK6 { > + regulator-name = "VDD_G3D_0.9V_AP"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + buck7_reg: BUCK7 { > + regulator-name = "VDD_MEM1_1.2V_AP"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + }; > + > + buck8_reg: BUCK8 { > + regulator-name = "VDD_LLDO_1.35V_AP"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + buck9_reg: BUCK9 { > + regulator-name = "VDD_MLDO_2.0V_AP"; > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + buck10_reg: BUCK10 { > + regulator-name = "vdd_mem2"; > + regulator-min-microvolt = <550000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > +&hsi2c_8 { > + status = "okay"; > + > + max77843@66 { > + compatible = "maxim,max77843"; > + interrupt-parent = <&gpa1>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + reg = <0x66>; > + > + muic: max77843-muic { > + compatible = "maxim,max77843-muic"; > + }; > + > + regulators { > + compatible = "maxim,max77843-regulator"; > + safeout1_reg: SAFEOUT1 { > + regulator-name = "SAFEOUT1"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <4950000>; > + }; > + > + safeout2_reg: SAFEOUT2 { > + regulator-name = "SAFEOUT2"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <4950000>; > + }; > + > + charger_reg: CHARGER { > + regulator-name = "CHARGER"; > + regulator-min-microamp = <100000>; > + regulator-max-microamp = <3150000>; > + }; > + }; > + > + haptic: max77843-haptic { > + compatible = "maxim,max77843-haptic"; > + haptic-supply = <&ldo38_reg>; > + pwms = <&pwm 0 33670 0>; > + pwm-names = "haptic"; > + }; > + }; > +}; > + > +&i2s0 { > + status = "okay"; > +}; > + > +&mshc_0 { > + status = "okay"; > + num-slots = <1>; > + non-removable; > + card-detect-delay = <200>; > + samsung,dw-mshc-ciu-div = <3>; > + samsung,dw-mshc-sdr-timing = <0 4>; > + samsung,dw-mshc-ddr-timing = <0 2>; > + samsung,dw-mshc-hs400-timing = <0 3>; > + samsung,read-strobe-delay = <90>; > + fifo-depth = <0x80>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4 > + &sd0_bus8 &sd0_rdqs>; > + bus-width = <8>; > + assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>; > + assigned-clock-rates = <800000000>; > +}; > + > +&pinctrl_alive { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_alive>; > + > + initial_alive: initial-state { > + PIN(IN, gpa0-0, DOWN, LV1); > + PIN(IN, gpa0-1, NONE, LV1); > + PIN(IN, gpa0-2, DOWN, LV1); > + PIN(IN, gpa0-3, NONE, LV1); > + PIN(IN, gpa0-4, NONE, LV1); > + PIN(IN, gpa0-5, DOWN, LV1); > + PIN(IN, gpa0-6, NONE, LV1); > + PIN(IN, gpa0-7, NONE, LV1); > + > + PIN(IN, gpa1-0, UP, LV1); > + PIN(IN, gpa1-1, NONE, LV1); > + PIN(IN, gpa1-2, NONE, LV1); > + PIN(IN, gpa1-3, DOWN, LV1); > + PIN(IN, gpa1-4, DOWN, LV1); > + PIN(IN, gpa1-5, NONE, LV1); > + PIN(IN, gpa1-6, NONE, LV1); > + PIN(IN, gpa1-7, NONE, LV1); > + > + PIN(IN, gpa2-0, NONE, LV1); > + PIN(IN, gpa2-1, NONE, LV1); > + PIN(IN, gpa2-2, NONE, LV1); > + PIN(IN, gpa2-3, DOWN, LV1); > + PIN(IN, gpa2-4, NONE, LV1); > + PIN(IN, gpa2-5, DOWN, LV1); > + PIN(IN, gpa2-6, DOWN, LV1); > + PIN(IN, gpa2-7, NONE, LV1); > + > + PIN(IN, gpa3-0, DOWN, LV1); > + PIN(IN, gpa3-1, DOWN, LV1); > + PIN(IN, gpa3-2, NONE, LV1); > + PIN(IN, gpa3-3, DOWN, LV1); > + PIN(IN, gpa3-4, NONE, LV1); > + PIN(IN, gpa3-5, DOWN, LV1); > + PIN(IN, gpa3-6, DOWN, LV1); > + PIN(IN, gpa3-7, DOWN, LV1); > + > + PIN(IN, gpf1-0, NONE, LV1); > + PIN(IN, gpf1-1, NONE, LV1); > + PIN(IN, gpf1-2, DOWN, LV1); > + PIN(IN, gpf1-4, UP, LV1); > + PIN(OUT, gpf1-5, NONE, LV1); > + PIN(IN, gpf1-6, DOWN, LV1); > + PIN(IN, gpf1-7, DOWN, LV1); > + > + PIN(IN, gpf2-0, DOWN, LV1); > + PIN(IN, gpf2-1, DOWN, LV1); > + PIN(IN, gpf2-2, DOWN, LV1); > + PIN(IN, gpf2-3, DOWN, LV1); > + > + PIN(IN, gpf3-0, DOWN, LV1); > + PIN(IN, gpf3-1, DOWN, LV1); > + PIN(IN, gpf3-2, NONE, LV1); > + PIN(IN, gpf3-3, DOWN, LV1); > + > + PIN(IN, gpf4-0, DOWN, LV1); > + PIN(IN, gpf4-1, DOWN, LV1); > + PIN(IN, gpf4-2, DOWN, LV1); > + PIN(IN, gpf4-3, DOWN, LV1); > + PIN(IN, gpf4-4, DOWN, LV1); > + PIN(IN, gpf4-5, DOWN, LV1); > + PIN(IN, gpf4-6, DOWN, LV1); > + PIN(IN, gpf4-7, DOWN, LV1); > + > + PIN(IN, gpf5-0, DOWN, LV1); > + PIN(IN, gpf5-1, DOWN, LV1); > + PIN(IN, gpf5-2, DOWN, LV1); > + PIN(IN, gpf5-3, DOWN, LV1); > + PIN(OUT, gpf5-4, NONE, LV1); > + PIN(IN, gpf5-5, DOWN, LV1); > + PIN(IN, gpf5-6, DOWN, LV1); > + PIN(IN, gpf5-7, DOWN, LV1); > + }; > + > + te_irq: te_irq { > + samsung,pins = "gpf1-3"; > + samsung,pin-function = <0xf>; > + }; > +}; > + > +&pinctrl_cpif { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_cpif>; > + > + initial_cpif: initial-state { > + PIN(IN, gpv6-0, DOWN, LV1); > + PIN(IN, gpv6-1, DOWN, LV1); > + }; > +}; > + > +&pinctrl_ese { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_ese>; > + > + initial_ese: initial-state { > + PIN(IN, gpj2-0, DOWN, LV1); > + PIN(IN, gpj2-1, DOWN, LV1); > + PIN(IN, gpj2-2, DOWN, LV1); > + }; > +}; > + > +&pinctrl_fsys { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_fsys>; > + > + initial_fsys: initial-state { > + PIN(IN, gpr3-0, NONE, LV1); > + PIN(IN, gpr3-1, DOWN, LV1); > + PIN(IN, gpr3-2, DOWN, LV1); > + PIN(IN, gpr3-3, DOWN, LV1); > + PIN(IN, gpr3-7, NONE, LV1); > + }; > +}; > + > +&pinctrl_imem { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_imem>; > + > + initial_imem: initial-state { > + PIN(IN, gpf0-0, UP, LV1); > + PIN(IN, gpf0-1, UP, LV1); > + PIN(IN, gpf0-2, DOWN, LV1); > + PIN(IN, gpf0-3, UP, LV1); > + PIN(IN, gpf0-4, DOWN, LV1); > + PIN(IN, gpf0-5, NONE, LV1); > + PIN(IN, gpf0-6, DOWN, LV1); > + PIN(IN, gpf0-7, UP, LV1); > + }; > +}; > + > +&pinctrl_nfc { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_nfc>; > + > + initial_nfc: initial-state { > + PIN(IN, gpj0-2, DOWN, LV1); > + }; > +}; > + > +&pinctrl_peric { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_peric>; > + > + initial_peric: initial-state { > + PIN(IN, gpv7-0, DOWN, LV1); > + PIN(IN, gpv7-1, DOWN, LV1); > + PIN(IN, gpv7-2, NONE, LV1); > + PIN(IN, gpv7-3, DOWN, LV1); > + PIN(IN, gpv7-4, DOWN, LV1); > + PIN(IN, gpv7-5, DOWN, LV1); > + > + PIN(IN, gpb0-4, DOWN, LV1); > + > + PIN(IN, gpc0-2, DOWN, LV1); > + PIN(IN, gpc0-5, DOWN, LV1); > + PIN(IN, gpc0-7, DOWN, LV1); > + > + PIN(IN, gpc1-1, DOWN, LV1); > + > + PIN(IN, gpc3-4, NONE, LV1); > + PIN(IN, gpc3-5, NONE, LV1); > + PIN(IN, gpc3-6, NONE, LV1); > + PIN(IN, gpc3-7, NONE, LV1); > + > + PIN(OUT, gpg0-0, NONE, LV1); > + PIN(FUNC1, gpg0-1, DOWN, LV1); > + > + PIN(IN, gpd2-5, DOWN, LV1); > + > + PIN(IN, gpd4-0, NONE, LV1); > + PIN(IN, gpd4-1, DOWN, LV1); > + PIN(IN, gpd4-2, DOWN, LV1); > + PIN(IN, gpd4-3, DOWN, LV1); > + PIN(IN, gpd4-4, DOWN, LV1); > + > + PIN(IN, gpd6-3, DOWN, LV1); > + > + PIN(IN, gpd8-1, UP, LV1); > + > + PIN(IN, gpg1-0, DOWN, LV1); > + PIN(IN, gpg1-1, DOWN, LV1); > + PIN(IN, gpg1-2, DOWN, LV1); > + PIN(IN, gpg1-3, DOWN, LV1); > + PIN(IN, gpg1-4, DOWN, LV1); > + > + PIN(IN, gpg2-0, DOWN, LV1); > + PIN(IN, gpg2-1, DOWN, LV1); > + > + PIN(IN, gpg3-0, DOWN, LV1); > + PIN(IN, gpg3-1, DOWN, LV1); > + PIN(IN, gpg3-5, DOWN, LV1); > + PIN(IN, gpg3-7, DOWN, LV1); > + }; > +}; > + > +&pinctrl_touch { > + pinctrl-names = "default"; > + pinctrl-0 = <&initial_touch>; > + > + initial_touch: initial-state { > + PIN(IN, gpj1-2, DOWN, LV1); > + }; > +}; > + > +&pwm { > + pinctrl-0 = <&pwm0_out>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&mic { > + status = "okay"; > + > + i80-if-timings { > + }; > +}; > + > +&serial_1 { > + status = "okay"; > +}; > + > +&serial_3 { > + assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>; > + assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>; > + status = "okay"; > +}; > + > +&spi_1 { > + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + > + wm5110: wm5110-codec@0 { > + compatible = "wlf,wm5110"; > + reg = <0x0>; > + spi-max-frequency = <20000000>; > + interrupt-parent = <&gpa0>; > + interrupts = <4 IRQ_TYPE_NONE>; > + clocks = <&pmu_system_controller 0>, > + <&s2mps13_osc S2MPS11_CLK_BT>; > + clock-names = "mclk1", "mclk2"; > + > + gpio-controller; > + #gpio-cells = <2>; > + > + wlf,micd-detect-debounce = <300>; > + wlf,micd-bias-start-time = <0x1>; > + wlf,micd-rate = <0x7>; > + wlf,micd-dbtime = <0x1>; > + wlf,micd-force-micbias; > + wlf,micd-configs = <0x0 1 0>; > + wlf,hpdet-channel = <1>; > + wlf,gpsw = <0x1>; > + wlf,inmode = <2 0 2 0>; > + > + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>; > + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>; > + > + /* core supplies */ > + AVDD-supply = <&ldo18_reg>; > + DBVDD1-supply = <&ldo18_reg>; > + CPVDD-supply = <&ldo18_reg>; > + DBVDD2-supply = <&ldo18_reg>; > + DBVDD3-supply = <&ldo18_reg>; > + > + controller-data { > + samsung,spi-feedback-delay = <0>; > + }; > + }; > +}; > + > +&timer { > + clock-frequency = <24000000>; > +}; > + > +&tmu_atlas0 { > + vtmu-supply = <&ldo3_reg>; > + status = "okay"; > +}; > + > +&tmu_apollo { > + vtmu-supply = <&ldo3_reg>; > + status = "okay"; > +}; > + > +&tmu_g3d { > + vtmu-supply = <&ldo3_reg>; > + status = "okay"; > +}; > + > +&usbdrd30 { > + vdd33-supply = <&ldo10_reg>; > + vdd10-supply = <&ldo6_reg>; > + status = "okay"; > +}; > + > +&usbdrd_dwc3_0 { > + dr_mode = "otg"; > +}; > + > +&usbdrd30_phy { > + vbus-supply = <&safeout1_reg>; > + status = "okay"; > +}; > + > +&xxti { > + clock-frequency = <24000000>; > +}; > -- > 1.9.1 >
On Thu, Nov 03, 2016 at 03:39:08PM +0900, Chanwoo Choi wrote: > This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board. > This board fully support the all things for mobile target. > > This patch supports the following devices: > 1. basic SoC > - Initial booting for Samsung Exynos5433 SoC > - DRAM LPDDR3 (3GB) > - eMMC (32GB) > - ARM architecture timer > > 2. power management devices > - Sasmung S2MPS13 PMIC for the power supply > - CPUFREQ for big.LITTLE cores > - TMU for big.LITTLE cores and GPU > - ADC with thermistor to measure the temperature of AP/Battery/Charger > - Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator) > > 3. sound devices > - I2S for sound bus > - LPASS for sound power control > - Wolfson WM5110 for sound codec > - Maxim MAX98504 for speaker amplifier > - TM2 ASoC Machine device driver node > > 3. display devices > - DECON, DSI and MIC for the panel output > > 4. usb devices > - USB 3.0 DRD (Dual Role Device) > - USB 3.0 Host controller > > 5. storage devices > - MSHC (Mobile Storage Host Controller) for eMMC device > > 6. misc devices > - gpio-keys (power, volume up/down, home key) > - PWM (Pulse Width Modulation Timer) > > Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> > Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> > Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> > Signed-off-by: Inki Dae <inki.dae@samsung.com> > Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com> > Signed-off-by: Beomho Seo <beomho.seo@samsung.com> > Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> > Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com> > Signed-off-by: Inha Song <ideal.song@samsung.com> > Signed-off-by: Ingi kim <ingi2.kim@samsung.com> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> > Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> > Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> > --- > .../bindings/arm/samsung/samsung-boards.txt | 1 + > arch/arm64/boot/dts/exynos/Makefile | 4 +- > arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 974 +++++++++++++++++++++ > 3 files changed, 978 insertions(+), 1 deletion(-) > create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts Thanks, applied. Best regards, Krzysztof
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14ef294..339af8b9cdc5 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -15,6 +15,7 @@ Required root node properties: - "samsung,xyref5260" - for Exynos5260-based Samsung board. - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,tm2" - for Exynos5433-based Samsung TM2 board. - "samsung,sd5v1" - for Exynos5440-based Samsung board. - "samsung,ssdk5440" - for Exynos5440-based Samsung board. diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile index 50c9b9383cfa..947c750acba1 100644 --- a/arch/arm64/boot/dts/exynos/Makefile +++ b/arch/arm64/boot/dts/exynos/Makefile @@ -1,4 +1,6 @@ -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb +dtb-$(CONFIG_ARCH_EXYNOS) += \ + exynos5433-tm2.dtb \ + exynos7-espresso.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts new file mode 100644 index 000000000000..9ea3f32bae9e --- /dev/null +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -0,0 +1,974 @@ +/* + * SAMSUNG Exynos5433 TM2 board device tree source + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * + * Device tree source file for Samsung's TM2 board which is based on + * Samsung Exynos5433 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5433.dtsi" +#include <dt-bindings/clock/samsung,s2mps11.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "Samsung TM2 board"; + compatible = "samsung,tm2", "samsung,exynos5433"; + + aliases { + pinctrl0 = &pinctrl_alive; + pinctrl1 = &pinctrl_aud; + pinctrl2 = &pinctrl_cpif; + pinctrl3 = &pinctrl_ese; + pinctrl4 = &pinctrl_finger; + pinctrl5 = &pinctrl_fsys; + pinctrl6 = &pinctrl_imem; + pinctrl7 = &pinctrl_nfc; + pinctrl8 = &pinctrl_peric; + pinctrl9 = &pinctrl_touch; + serial0 = &serial_0; + serial1 = &serial_1; + serial2 = &serial_2; + serial3 = &serial_3; + spi0 = &spi_0; + spi1 = &spi_1; + spi2 = &spi_2; + spi3 = &spi_3; + spi4 = &spi_4; + }; + + chosen { + stdout-path = &serial_1; + }; + + memory@20000000 { + device_type = "memory"; + reg = <0x0 0x20000000 0x0 0xc0000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power-key { + gpios = <&gpa2 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + label = "power key"; + debounce-interval = <10>; + }; + + volume-up-key { + gpios = <&gpa2 0 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + label = "volume-up key"; + debounce-interval = <10>; + }; + + volume-down-key { + gpios = <&gpa2 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + label = "volume-down key"; + debounce-interval = <10>; + }; + + homepage-key { + gpios = <&gpa0 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + label = "homepage key"; + debounce-interval = <10>; + }; + }; + + i2c_max98504: i2c-gpio-0 { + compatible = "i2c-gpio"; + gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */ + &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + max98504: max98504@31 { + compatible = "maxim,max98504"; + reg = <0x31>; + maxim,rx-path = <1>; + maxim,tx-path = <1>; + maxim,tx-channel-mask = <3>; + maxim,tx-channel-source = <2>; + }; + }; + + sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 GPIO_ACTIVE_HIGH>; + model = "wm5110"; + samsung,audio-routing = + /* Headphone */ + "HP", "HPOUT1L", + "HP", "HPOUT1R", + + /* Speaker */ + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + + /* Receiver */ + "RCV", "HPOUT3L", + "RCV", "HPOUT3R"; + status = "okay"; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; + + thermistor-ap { + compatible = "murata,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 0>; + }; + + thermistor-battery { + compatible = "murata,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 1>; + #thermal-sensor-cells = <0>; + }; + + thermistor-charger { + compatible = "murata,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 2>; + }; +}; + +&cpu0 { + cpu-supply = <&buck3_reg>; +}; + +&cpu4 { + cpu-supply = <&buck2_reg>; +}; + +&decon { + status = "okay"; + + i80-if-timings { + }; +}; + +&dsi { + status = "okay"; + vddcore-supply = <&ldo6_reg>; + vddio-supply = <&ldo7_reg>; + samsung,pll-clock-frequency = <24000000>; + pinctrl-names = "default"; + pinctrl-0 = <&te_irq>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + dsi_out: endpoint { + samsung,burst-clock-frequency = <512000000>; + samsung,esc-clock-frequency = <16000000>; + }; + }; + }; +}; + +&hsi2c_0 { + status = "okay"; + clock-frequency = <2500000>; + + s2mps13-pmic@66 { + compatible = "samsung,s2mps13-pmic"; + interrupt-parent = <&gpa0>; + interrupts = <7 IRQ_TYPE_NONE>; + reg = <0x66>; + samsung,s2mps11-wrstbi-ground; + + s2mps13_osc: clocks { + compatible = "samsung,s2mps13-clk"; + #clock-cells = <1>; + clock-output-names = "s2mps13_ap", "s2mps13_cp", + "s2mps13_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_0.9V_AP"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo3_reg: LDO3 { + regulator-name = "VDD1_E_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "VDD10_MIF_PLL_1.0V_AP"; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo5_reg: LDO5 { + regulator-name = "VDD10_DPLL_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo6_reg: LDO6 { + regulator-name = "VDD10_MIPI2L_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo7_reg: LDO7 { + regulator-name = "VDD18_MIPI2L_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo8_reg: LDO8 { + regulator-name = "VDD18_LLI_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo9_reg: LDO9 { + regulator-name = "VDD18_ABB_ETC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo10_reg: LDO10 { + regulator-name = "VDD33_USB30_3.0V_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo11_reg: LDO11 { + regulator-name = "VDD_INT_M_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo12_reg: LDO12 { + regulator-name = "VDD_KFC_M_1.1V_AP"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + ldo13_reg: LDO13 { + regulator-name = "VDD_G3D_M_0.95V_AP"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <950000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo14_reg: LDO14 { + regulator-name = "VDDQ_M1_LDO_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo15_reg: LDO15 { + regulator-name = "VDDQ_M2_LDO_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo16_reg: LDO16 { + regulator-name = "VDDQ_EFUSE"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + ldo17_reg: LDO17 { + regulator-name = "V_TFLASH_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "V_CODEC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo19_reg: LDO19 { + regulator-name = "VDDA_1.8V_COMP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo20_reg: LDO20 { + regulator-name = "VCC_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo21_reg: LDO21 { + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo22_reg: LDO22 { + regulator-name = "CAM_IO_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo23_reg: LDO23 { + regulator-name = "CAM_SEN_CORE_1.2V_AP"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1200000>; + }; + + ldo24_reg: LDO24 { + regulator-name = "VT_CAM_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + ldo25_reg: LDO25 { + regulator-name = "CAM_SEN_A2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo26_reg: LDO26 { + regulator-name = "CAM_AF_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo27_reg: LDO27 { + regulator-name = "VCC_3.0V_LCD_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo28_reg: LDO28 { + regulator-name = "VCC_1.8V_LCD_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo29_reg: LDO29 { + regulator-name = "VT_CAM_2.8V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo30_reg: LDO30 { + regulator-name = "TSP_AVDD_3.3V_AP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo31_reg: LDO31 { + regulator-name = "TSP_VDD_1.85V_AP"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; + }; + + ldo32_reg: LDO32 { + regulator-name = "VTOUCH_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo33_reg: LDO33 { + regulator-name = "VTOUCH_LED_3.3V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12500>; + }; + + ldo34_reg: LDO34 { + regulator-name = "VCC_1.8V_MHL_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2100000>; + }; + + ldo35_reg: LDO35 { + regulator-name = "OIS_VM_2.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo36_reg: LDO36 { + regulator-name = "VSIL_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo37_reg: LDO37 { + regulator-name = "VF_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo38_reg: LDO38 { + regulator-name = "VCC_3.0V_MOTOR_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo39_reg: LDO39 { + regulator-name = "V_HRM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo40_reg: LDO40 { + regulator-name = "V_HRM_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck2_reg: BUCK2 { + regulator-name = "VDD_EGL_1.0V_AP"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck3_reg: BUCK3 { + regulator-name = "VDD_KFC_1.0V_AP"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck4_reg: BUCK4 { + regulator-name = "VDD_INT_0.95V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck5_reg: BUCK5 { + regulator-name = "VDD_DISP_CAM0_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck6_reg: BUCK6 { + regulator-name = "VDD_G3D_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck7_reg: BUCK7 { + regulator-name = "VDD_MEM1_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "VDD_LLDO_1.35V_AP"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "VDD_MLDO_2.0V_AP"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + buck10_reg: BUCK10 { + regulator-name = "vdd_mem2"; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + }; + }; +}; + +&hsi2c_8 { + status = "okay"; + + max77843@66 { + compatible = "maxim,max77843"; + interrupt-parent = <&gpa1>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reg = <0x66>; + + muic: max77843-muic { + compatible = "maxim,max77843-muic"; + }; + + regulators { + compatible = "maxim,max77843-regulator"; + safeout1_reg: SAFEOUT1 { + regulator-name = "SAFEOUT1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <4950000>; + }; + + safeout2_reg: SAFEOUT2 { + regulator-name = "SAFEOUT2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <4950000>; + }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <100000>; + regulator-max-microamp = <3150000>; + }; + }; + + haptic: max77843-haptic { + compatible = "maxim,max77843-haptic"; + haptic-supply = <&ldo38_reg>; + pwms = <&pwm 0 33670 0>; + pwm-names = "haptic"; + }; + }; +}; + +&i2s0 { + status = "okay"; +}; + +&mshc_0 { + status = "okay"; + num-slots = <1>; + non-removable; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 3>; + samsung,read-strobe-delay = <90>; + fifo-depth = <0x80>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4 + &sd0_bus8 &sd0_rdqs>; + bus-width = <8>; + assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>; + assigned-clock-rates = <800000000>; +}; + +&pinctrl_alive { + pinctrl-names = "default"; + pinctrl-0 = <&initial_alive>; + + initial_alive: initial-state { + PIN(IN, gpa0-0, DOWN, LV1); + PIN(IN, gpa0-1, NONE, LV1); + PIN(IN, gpa0-2, DOWN, LV1); + PIN(IN, gpa0-3, NONE, LV1); + PIN(IN, gpa0-4, NONE, LV1); + PIN(IN, gpa0-5, DOWN, LV1); + PIN(IN, gpa0-6, NONE, LV1); + PIN(IN, gpa0-7, NONE, LV1); + + PIN(IN, gpa1-0, UP, LV1); + PIN(IN, gpa1-1, NONE, LV1); + PIN(IN, gpa1-2, NONE, LV1); + PIN(IN, gpa1-3, DOWN, LV1); + PIN(IN, gpa1-4, DOWN, LV1); + PIN(IN, gpa1-5, NONE, LV1); + PIN(IN, gpa1-6, NONE, LV1); + PIN(IN, gpa1-7, NONE, LV1); + + PIN(IN, gpa2-0, NONE, LV1); + PIN(IN, gpa2-1, NONE, LV1); + PIN(IN, gpa2-2, NONE, LV1); + PIN(IN, gpa2-3, DOWN, LV1); + PIN(IN, gpa2-4, NONE, LV1); + PIN(IN, gpa2-5, DOWN, LV1); + PIN(IN, gpa2-6, DOWN, LV1); + PIN(IN, gpa2-7, NONE, LV1); + + PIN(IN, gpa3-0, DOWN, LV1); + PIN(IN, gpa3-1, DOWN, LV1); + PIN(IN, gpa3-2, NONE, LV1); + PIN(IN, gpa3-3, DOWN, LV1); + PIN(IN, gpa3-4, NONE, LV1); + PIN(IN, gpa3-5, DOWN, LV1); + PIN(IN, gpa3-6, DOWN, LV1); + PIN(IN, gpa3-7, DOWN, LV1); + + PIN(IN, gpf1-0, NONE, LV1); + PIN(IN, gpf1-1, NONE, LV1); + PIN(IN, gpf1-2, DOWN, LV1); + PIN(IN, gpf1-4, UP, LV1); + PIN(OUT, gpf1-5, NONE, LV1); + PIN(IN, gpf1-6, DOWN, LV1); + PIN(IN, gpf1-7, DOWN, LV1); + + PIN(IN, gpf2-0, DOWN, LV1); + PIN(IN, gpf2-1, DOWN, LV1); + PIN(IN, gpf2-2, DOWN, LV1); + PIN(IN, gpf2-3, DOWN, LV1); + + PIN(IN, gpf3-0, DOWN, LV1); + PIN(IN, gpf3-1, DOWN, LV1); + PIN(IN, gpf3-2, NONE, LV1); + PIN(IN, gpf3-3, DOWN, LV1); + + PIN(IN, gpf4-0, DOWN, LV1); + PIN(IN, gpf4-1, DOWN, LV1); + PIN(IN, gpf4-2, DOWN, LV1); + PIN(IN, gpf4-3, DOWN, LV1); + PIN(IN, gpf4-4, DOWN, LV1); + PIN(IN, gpf4-5, DOWN, LV1); + PIN(IN, gpf4-6, DOWN, LV1); + PIN(IN, gpf4-7, DOWN, LV1); + + PIN(IN, gpf5-0, DOWN, LV1); + PIN(IN, gpf5-1, DOWN, LV1); + PIN(IN, gpf5-2, DOWN, LV1); + PIN(IN, gpf5-3, DOWN, LV1); + PIN(OUT, gpf5-4, NONE, LV1); + PIN(IN, gpf5-5, DOWN, LV1); + PIN(IN, gpf5-6, DOWN, LV1); + PIN(IN, gpf5-7, DOWN, LV1); + }; + + te_irq: te_irq { + samsung,pins = "gpf1-3"; + samsung,pin-function = <0xf>; + }; +}; + +&pinctrl_cpif { + pinctrl-names = "default"; + pinctrl-0 = <&initial_cpif>; + + initial_cpif: initial-state { + PIN(IN, gpv6-0, DOWN, LV1); + PIN(IN, gpv6-1, DOWN, LV1); + }; +}; + +&pinctrl_ese { + pinctrl-names = "default"; + pinctrl-0 = <&initial_ese>; + + initial_ese: initial-state { + PIN(IN, gpj2-0, DOWN, LV1); + PIN(IN, gpj2-1, DOWN, LV1); + PIN(IN, gpj2-2, DOWN, LV1); + }; +}; + +&pinctrl_fsys { + pinctrl-names = "default"; + pinctrl-0 = <&initial_fsys>; + + initial_fsys: initial-state { + PIN(IN, gpr3-0, NONE, LV1); + PIN(IN, gpr3-1, DOWN, LV1); + PIN(IN, gpr3-2, DOWN, LV1); + PIN(IN, gpr3-3, DOWN, LV1); + PIN(IN, gpr3-7, NONE, LV1); + }; +}; + +&pinctrl_imem { + pinctrl-names = "default"; + pinctrl-0 = <&initial_imem>; + + initial_imem: initial-state { + PIN(IN, gpf0-0, UP, LV1); + PIN(IN, gpf0-1, UP, LV1); + PIN(IN, gpf0-2, DOWN, LV1); + PIN(IN, gpf0-3, UP, LV1); + PIN(IN, gpf0-4, DOWN, LV1); + PIN(IN, gpf0-5, NONE, LV1); + PIN(IN, gpf0-6, DOWN, LV1); + PIN(IN, gpf0-7, UP, LV1); + }; +}; + +&pinctrl_nfc { + pinctrl-names = "default"; + pinctrl-0 = <&initial_nfc>; + + initial_nfc: initial-state { + PIN(IN, gpj0-2, DOWN, LV1); + }; +}; + +&pinctrl_peric { + pinctrl-names = "default"; + pinctrl-0 = <&initial_peric>; + + initial_peric: initial-state { + PIN(IN, gpv7-0, DOWN, LV1); + PIN(IN, gpv7-1, DOWN, LV1); + PIN(IN, gpv7-2, NONE, LV1); + PIN(IN, gpv7-3, DOWN, LV1); + PIN(IN, gpv7-4, DOWN, LV1); + PIN(IN, gpv7-5, DOWN, LV1); + + PIN(IN, gpb0-4, DOWN, LV1); + + PIN(IN, gpc0-2, DOWN, LV1); + PIN(IN, gpc0-5, DOWN, LV1); + PIN(IN, gpc0-7, DOWN, LV1); + + PIN(IN, gpc1-1, DOWN, LV1); + + PIN(IN, gpc3-4, NONE, LV1); + PIN(IN, gpc3-5, NONE, LV1); + PIN(IN, gpc3-6, NONE, LV1); + PIN(IN, gpc3-7, NONE, LV1); + + PIN(OUT, gpg0-0, NONE, LV1); + PIN(FUNC1, gpg0-1, DOWN, LV1); + + PIN(IN, gpd2-5, DOWN, LV1); + + PIN(IN, gpd4-0, NONE, LV1); + PIN(IN, gpd4-1, DOWN, LV1); + PIN(IN, gpd4-2, DOWN, LV1); + PIN(IN, gpd4-3, DOWN, LV1); + PIN(IN, gpd4-4, DOWN, LV1); + + PIN(IN, gpd6-3, DOWN, LV1); + + PIN(IN, gpd8-1, UP, LV1); + + PIN(IN, gpg1-0, DOWN, LV1); + PIN(IN, gpg1-1, DOWN, LV1); + PIN(IN, gpg1-2, DOWN, LV1); + PIN(IN, gpg1-3, DOWN, LV1); + PIN(IN, gpg1-4, DOWN, LV1); + + PIN(IN, gpg2-0, DOWN, LV1); + PIN(IN, gpg2-1, DOWN, LV1); + + PIN(IN, gpg3-0, DOWN, LV1); + PIN(IN, gpg3-1, DOWN, LV1); + PIN(IN, gpg3-5, DOWN, LV1); + PIN(IN, gpg3-7, DOWN, LV1); + }; +}; + +&pinctrl_touch { + pinctrl-names = "default"; + pinctrl-0 = <&initial_touch>; + + initial_touch: initial-state { + PIN(IN, gpj1-2, DOWN, LV1); + }; +}; + +&pwm { + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&mic { + status = "okay"; + + i80-if-timings { + }; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_3 { + assigned-clocks = <&cmu_aud CLK_MOUT_AUD_PLL_USER>; + assigned-clock-parents = <&cmu_top CLK_FOUT_AUD_PLL>; + status = "okay"; +}; + +&spi_1 { + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>; + status = "okay"; + + wm5110: wm5110-codec@0 { + compatible = "wlf,wm5110"; + reg = <0x0>; + spi-max-frequency = <20000000>; + interrupt-parent = <&gpa0>; + interrupts = <4 IRQ_TYPE_NONE>; + clocks = <&pmu_system_controller 0>, + <&s2mps13_osc S2MPS11_CLK_BT>; + clock-names = "mclk1", "mclk2"; + + gpio-controller; + #gpio-cells = <2>; + + wlf,micd-detect-debounce = <300>; + wlf,micd-bias-start-time = <0x1>; + wlf,micd-rate = <0x7>; + wlf,micd-dbtime = <0x1>; + wlf,micd-force-micbias; + wlf,micd-configs = <0x0 1 0>; + wlf,hpdet-channel = <1>; + wlf,gpsw = <0x1>; + wlf,inmode = <2 0 2 0>; + + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>; + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>; + + /* core supplies */ + AVDD-supply = <&ldo18_reg>; + DBVDD1-supply = <&ldo18_reg>; + CPVDD-supply = <&ldo18_reg>; + DBVDD2-supply = <&ldo18_reg>; + DBVDD3-supply = <&ldo18_reg>; + + controller-data { + samsung,spi-feedback-delay = <0>; + }; + }; +}; + +&timer { + clock-frequency = <24000000>; +}; + +&tmu_atlas0 { + vtmu-supply = <&ldo3_reg>; + status = "okay"; +}; + +&tmu_apollo { + vtmu-supply = <&ldo3_reg>; + status = "okay"; +}; + +&tmu_g3d { + vtmu-supply = <&ldo3_reg>; + status = "okay"; +}; + +&usbdrd30 { + vdd33-supply = <&ldo10_reg>; + vdd10-supply = <&ldo6_reg>; + status = "okay"; +}; + +&usbdrd_dwc3_0 { + dr_mode = "otg"; +}; + +&usbdrd30_phy { + vbus-supply = <&safeout1_reg>; + status = "okay"; +}; + +&xxti { + clock-frequency = <24000000>; +};