| Message ID | 1481536123-9279-1-git-send-email-rasmus.villemoes@prevas.dk (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 12/12/2016 01:48 AM, Rasmus Villemoes wrote: > A bootloader may start the watchdog device before handing control to > the kernel - in that case, we should tell the kernel about it so the > watchdog framework can keep it alive until userspace opens > /dev/watchdog0. > > Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Guenter Roeck <linux@roeck-us.net> > --- > drivers/watchdog/bcm2835_wdt.c | 20 ++++++++++++++++++++ > 1 file changed, 20 insertions(+) > > diff --git a/drivers/watchdog/bcm2835_wdt.c b/drivers/watchdog/bcm2835_wdt.c > index 4dddd82..c32c45b 100644 > --- a/drivers/watchdog/bcm2835_wdt.c > +++ b/drivers/watchdog/bcm2835_wdt.c > @@ -55,6 +55,15 @@ struct bcm2835_wdt { > static unsigned int heartbeat; > static bool nowayout = WATCHDOG_NOWAYOUT; > > +static bool bcm2835_wdt_is_running(struct bcm2835_wdt *wdt) > +{ > + uint32_t cur; > + > + cur = readl(wdt->base + PM_RSTC); > + > + return !!(cur & PM_RSTC_WRCFG_FULL_RESET); > +} > + > static int bcm2835_wdt_start(struct watchdog_device *wdog) > { > struct bcm2835_wdt *wdt = watchdog_get_drvdata(wdog); > @@ -181,6 +190,17 @@ static int bcm2835_wdt_probe(struct platform_device *pdev) > watchdog_init_timeout(&bcm2835_wdt_wdd, heartbeat, dev); > watchdog_set_nowayout(&bcm2835_wdt_wdd, nowayout); > bcm2835_wdt_wdd.parent = &pdev->dev; > + if (bcm2835_wdt_is_running(wdt)) { > + /* > + * The currently active timeout value (set by the > + * bootloader) may be different from the module > + * heartbeat parameter or the value in device > + * tree. But we just need to set WDOG_HW_RUNNING, > + * because then the framework will "immediately" ping > + * the device, updating the timeout. > + */ > + set_bit(WDOG_HW_RUNNING, &bcm2835_wdt_wdd.status); > + } > err = watchdog_register_device(&bcm2835_wdt_wdd); > if (err) { > dev_err(dev, "Failed to register watchdog device"); >
Rasmus Villemoes <rasmus.villemoes@prevas.dk> writes: > A bootloader may start the watchdog device before handing control to > the kernel - in that case, we should tell the kernel about it so the > watchdog framework can keep it alive until userspace opens > /dev/watchdog0. I don't believe our current bootloaders (the closed firmware or u-boot) set up the watchdog, but this seems reasonable since they might want to later. Acked-by: Eric Anholt <eric@anholt.net>
diff --git a/drivers/watchdog/bcm2835_wdt.c b/drivers/watchdog/bcm2835_wdt.c index 4dddd82..c32c45b 100644 --- a/drivers/watchdog/bcm2835_wdt.c +++ b/drivers/watchdog/bcm2835_wdt.c @@ -55,6 +55,15 @@ struct bcm2835_wdt { static unsigned int heartbeat; static bool nowayout = WATCHDOG_NOWAYOUT; +static bool bcm2835_wdt_is_running(struct bcm2835_wdt *wdt) +{ + uint32_t cur; + + cur = readl(wdt->base + PM_RSTC); + + return !!(cur & PM_RSTC_WRCFG_FULL_RESET); +} + static int bcm2835_wdt_start(struct watchdog_device *wdog) { struct bcm2835_wdt *wdt = watchdog_get_drvdata(wdog); @@ -181,6 +190,17 @@ static int bcm2835_wdt_probe(struct platform_device *pdev) watchdog_init_timeout(&bcm2835_wdt_wdd, heartbeat, dev); watchdog_set_nowayout(&bcm2835_wdt_wdd, nowayout); bcm2835_wdt_wdd.parent = &pdev->dev; + if (bcm2835_wdt_is_running(wdt)) { + /* + * The currently active timeout value (set by the + * bootloader) may be different from the module + * heartbeat parameter or the value in device + * tree. But we just need to set WDOG_HW_RUNNING, + * because then the framework will "immediately" ping + * the device, updating the timeout. + */ + set_bit(WDOG_HW_RUNNING, &bcm2835_wdt_wdd.status); + } err = watchdog_register_device(&bcm2835_wdt_wdd); if (err) { dev_err(dev, "Failed to register watchdog device");
A bootloader may start the watchdog device before handing control to the kernel - in that case, we should tell the kernel about it so the watchdog framework can keep it alive until userspace opens /dev/watchdog0. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> --- drivers/watchdog/bcm2835_wdt.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)