@@ -1,17 +1,28 @@
-* Marvell Armada 375 Ethernet Controller (PPv2)
+* Marvell Armada 375 Ethernet Controller (PPv2.1)
+ Marvell Armada 7K/8K Ethernet Controller (PPv2.2)
Required properties:
-- compatible: should be "marvell,armada-375-pp2"
+- compatible: should be one of:
+ "marvell,armada-375-pp2"
+ "marvell,armada-7k-pp2"
- reg: addresses and length of the register sets for the device.
- Must contain the following register sets:
+ For "marvell,armada-375-pp2", must contain the following register
+ sets:
- common controller registers
- LMS registers
- In addition, at least one port register set is required.
-- clocks: a pointer to the reference clocks for this device, consequently:
- - main controller clock
- - GOP clock
-- clock-names: names of used clocks, must be "pp_clk" and "gop_clk".
+ - one register area per Ethernet port
+ For "marvell,armada-7k-pp2", must contain the following register
+ sets:
+ - packet processor registers
+ - networking interfaces registers
+
+- clocks: pointers to the reference clocks for this device, consequently:
+ - main controller clock (for both armada-375-pp2 and armada-7k-pp2)
+ - GOP clock (for both armada-375-pp2 and armada-7k-pp2)
+ - MG clock (only for armada-7k-pp2)
+- clock-names: names of used clocks, must be "pp_clk", "gop_clk" and
+ "mg_clk" (the latter only for armada-7k-pp2).
The ethernet ports are represented by subnodes. At least one port is
required.
@@ -19,8 +30,10 @@ required.
Required properties (port):
- interrupts: interrupt for the port
-- port-id: should be '0' or '1' for ethernet ports, and '2' for the
- loopback port
+- port-id: ID of the port from the MAC point of view
+- gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the
+ GOP (Group Of Ports) point of view. This ID is used to index the
+ per-port registers in the second register area.
- phy-mode: See ethernet.txt file in the same directory
Optional properties (port):
@@ -29,7 +42,7 @@ Optional properties (port):
- phy: a phandle to a phy node defining the PHY address (as the reg
property, a single integer).
-Example:
+Example for marvell,armada-375-pp2:
ethernet@f0000 {
compatible = "marvell,armada-375-pp2";
@@ -57,3 +70,30 @@ ethernet@f0000 {
phy-mode = "gmii";
};
};
+
+Example for marvell,armada-7k-pp2:
+
+cpm_ethernet: ethernet@0 {
+ compatible = "marvell,armada-7k-pp22";
+ reg = <0x0 0x100000>, <0x129000 0xb000>;
+ clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, <&cpm_syscon0 1 5>;
+ clock-names = "pp_clk", "gop_clk", "gp_clk";
+
+ eth0: eth0 {
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ port-id = <0>;
+ gop-port-id = <0>;
+ };
+
+ eth1: eth1 {
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ port-id = <1>;
+ gop-port-id = <2>;
+ };
+
+ eth2: eth2 {
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ port-id = <2>;
+ gop-port-id = <3>;
+ };
+};
The Marvell PPv2 Device Tree binding was so far only used to describe the PPv2.1 network controller, used in the Marvell Armada 375. A new version of this IP block, PPv2.2 is used in the Marvell Armada 7K/8K processor. This commit extends the existing binding so that it can also be used to describe PPv2.2 hardware. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> --- .../devicetree/bindings/net/marvell-pp2.txt | 62 ++++++++++++++++++---- 1 file changed, 51 insertions(+), 11 deletions(-)