| Message ID | 1498035645-22804-3-git-send-email-xuejiancheng@hisilicon.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Wed, Jun 21, 2017 at 05:00:42PM +0800, Jiancheng Xue wrote: > Add support for hisi-inno-usb2 phy. > > Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com> > --- > .../devicetree/bindings/phy/phy-hisi-inno-usb2.txt | 36 ++++++++++++++++++++++ > 1 file changed, 36 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt > > diff --git a/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt > new file mode 100644 > index 0000000..21f8208 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt > @@ -0,0 +1,36 @@ > +HiSilicon INNO USB2 PHY > +----------------------- > +Required properties: > +- compatible: Should be one of the following strings: > + "hisilicon,inno-usb2-phy", > + "hisilicon,hi3798cv200-usb2-phy", > +- #phy-cells: Must be 0 > +- hisilicon,peripheral-syscon: Phandle of syscon used to control phy. > +- clocks: Phandle and clock specifier pair for reference clock utmi_refclk. > +- resets: List of phandle and reset specifier pairs for each reset signal in > +reset-names. > +- reset-names: Should be "por_rst" and "test_rst". The test_rst only > +exists in some of SOCs, so it is optional. _rst is redundant. > + > +Phy node can include up to four subnodes. Each subnode represents one port. > +The required properties of port node are as follows: > +- clocks: Phandle and clock specifier pair for utmi_clock. > +- resets: List of phandle and reset specifier pairs for port reset and utmi reset. > +- reset-names: List of reset signal names. Should be "port_rst" and "utmi_rst" > + > +Refer to phy/phy-bindings.txt for the generic PHY binding properties > + > +Example: > +usb_phy: phy { > + compatible = "hisilicon,inno_usb2_phy"; Doesn't match the above compatible. > + #phy-cells = <0>; > + hisilicon,peripheral-syscon = <&peri_ctrl>; > + clocks = <&crg USB2_REF_CLK>; > + resets = <&crg 0xb4 2>; > + reset-names = "por_rst"; > + port0 { port@0 and provide a reg property. > + clocks = <&crg USB2_UTMI0_CLK>; > + resets = <&crg 0xb4 5>, <&crg 0xb4 1>; > + reset-names = "port_rst", "utmi_rst"; > + }; > + }; > -- > 1.9.1 > > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt new file mode 100644 index 0000000..21f8208 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt @@ -0,0 +1,36 @@ +HiSilicon INNO USB2 PHY +----------------------- +Required properties: +- compatible: Should be one of the following strings: + "hisilicon,inno-usb2-phy", + "hisilicon,hi3798cv200-usb2-phy", +- #phy-cells: Must be 0 +- hisilicon,peripheral-syscon: Phandle of syscon used to control phy. +- clocks: Phandle and clock specifier pair for reference clock utmi_refclk. +- resets: List of phandle and reset specifier pairs for each reset signal in +reset-names. +- reset-names: Should be "por_rst" and "test_rst". The test_rst only +exists in some of SOCs, so it is optional. + +Phy node can include up to four subnodes. Each subnode represents one port. +The required properties of port node are as follows: +- clocks: Phandle and clock specifier pair for utmi_clock. +- resets: List of phandle and reset specifier pairs for port reset and utmi reset. +- reset-names: List of reset signal names. Should be "port_rst" and "utmi_rst" + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: +usb_phy: phy { + compatible = "hisilicon,inno_usb2_phy"; + #phy-cells = <0>; + hisilicon,peripheral-syscon = <&peri_ctrl>; + clocks = <&crg USB2_REF_CLK>; + resets = <&crg 0xb4 2>; + reset-names = "por_rst"; + port0 { + clocks = <&crg USB2_UTMI0_CLK>; + resets = <&crg 0xb4 5>, <&crg 0xb4 1>; + reset-names = "port_rst", "utmi_rst"; + }; + };
Add support for hisi-inno-usb2 phy. Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com> --- .../devicetree/bindings/phy/phy-hisi-inno-usb2.txt | 36 ++++++++++++++++++++++ 1 file changed, 36 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt