| Message ID | 1515738618-3617-3-git-send-email-jagan@amarulasolutions.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, Jan 12, 2018 at 2:30 PM, Jagan Teki <jagan@amarulasolutions.com> wrote: > Add usb otg support for bananapi-m64 board, > - USB-ID connected with PH9 > - USB-DRVVBUS controlled by N_VBUSEN pin from PMIC > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> > --- > Changes for v4: > - rebase on master > - tested otg host mode. > Changes for v3: > - Move the position of reg_drivevbus as per binding documentation. > Changes for v2: > - add drvvbus regulator > - add N_VBUSEN pin > > .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 21 +++++++++++++++++++++ > 1 file changed, 21 insertions(+) > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts > index a697567..26e8534 100644 > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts > @@ -86,6 +86,10 @@ > }; > }; > > +&ehci0 { > + status = "okay"; > +}; > + > &ehci1 { > status = "okay"; > }; > @@ -156,6 +160,10 @@ > status = "okay"; > }; > > +&ohci0 { > + status = "okay"; > +}; > + > &ohci1 { > status = "okay"; > }; > @@ -168,6 +176,7 @@ > reg = <0x3a3>; > interrupt-parent = <&r_intc>; > interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ > }; > }; > > @@ -283,6 +292,11 @@ > regulator-name = "vcc-rtc"; > }; > > +®_drivevbus { Please keep the nodes in alphabetical order. Otherwise, Reviewed-by: Chen-Yu Tsai <wens@csie.org> > + regulator-name = "usb0-vbus"; > + status = "okay"; > +}; > + > &uart0 { > pinctrl-names = "default"; > pinctrl-0 = <&uart0_pins_a>; > @@ -295,6 +309,13 @@ > status = "okay"; > }; > > +&usb_otg { > + dr_mode = "otg"; > + status = "okay"; > +}; > + > &usbphy { > + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ > + usb0_vbus-supply = <®_drivevbus>; > status = "okay"; > }; > -- > 2.7.4 >
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts index a697567..26e8534 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts @@ -86,6 +86,10 @@ }; }; +&ehci0 { + status = "okay"; +}; + &ehci1 { status = "okay"; }; @@ -156,6 +160,10 @@ status = "okay"; }; +&ohci0 { + status = "okay"; +}; + &ohci1 { status = "okay"; }; @@ -168,6 +176,7 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; @@ -283,6 +292,11 @@ regulator-name = "vcc-rtc"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; @@ -295,6 +309,13 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; status = "okay"; };
Add usb otg support for bananapi-m64 board, - USB-ID connected with PH9 - USB-DRVVBUS controlled by N_VBUSEN pin from PMIC Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v4: - rebase on master - tested otg host mode. Changes for v3: - Move the position of reg_drivevbus as per binding documentation. Changes for v2: - add drvvbus regulator - add N_VBUSEN pin .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)