@@ -13794,6 +13794,13 @@ F: arch/arm/mach-davinci/
F: drivers/i2c/busses/i2c-davinci.c
F: arch/arm/boot/dts/da850*
+TI DAVINCI SERIES CLOCK DRIVER
+M: David Lechner <david@lechnology.com>
+R: Sekhar Nori <nsekhar@ti.com>
+S: Maintained
+F: Documentation/devicetree/bindings/clock/ti/davinci/
+F: drivers/clk/davinci/
+
TI DAVINCI SERIES GPIO DRIVER
M: Keerthy <j-keerthy@ti.com>
L: linux-gpio@vger.kernel.org
@@ -61,6 +61,7 @@ obj-$(CONFIG_ARCH_ARTPEC) += axis/
obj-$(CONFIG_ARC_PLAT_AXS10X) += axs10x/
obj-y += bcm/
obj-$(CONFIG_ARCH_BERLIN) += berlin/
+obj-$(CONFIG_ARCH_DAVINCI) += davinci/
obj-$(CONFIG_H8300) += h8300/
obj-$(CONFIG_ARCH_HISI) += hisilicon/
obj-y += imgtec/
new file mode 100644
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+
+ifeq ($(CONFIG_COMMON_CLK), y)
+obj-y += pll.o
+endif
new file mode 100644
@@ -0,0 +1,864 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PLL clock driver for TI Davinci SoCs
+ *
+ * Copyright (C) 2018 David Lechner <david@lechnology.com>
+ *
+ * Based on arch/arm/mach-davinci/clock.c
+ * Copyright (C) 2006-2007 Texas Instruments.
+ * Copyright (C) 2008-2009 Deep Root Systems, LLC
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/notifier.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include "pll.h"
+
+#define MAX_NAME_SIZE 20
+#define OSCIN_CLK_NAME "oscin"
+
+#define REVID 0x000
+#define PLLCTL 0x100
+#define OCSEL 0x104
+#define PLLSECCTL 0x108
+#define PLLM 0x110
+#define PREDIV 0x114
+#define PLLDIV1 0x118
+#define PLLDIV2 0x11c
+#define PLLDIV3 0x120
+#define OSCDIV 0x124
+#define POSTDIV 0x128
+#define BPDIV 0x12c
+#define PLLCMD 0x138
+#define PLLSTAT 0x13c
+#define ALNCTL 0x140
+#define DCHANGE 0x144
+#define CKEN 0x148
+#define CKSTAT 0x14c
+#define SYSTAT 0x150
+#define PLLDIV4 0x160
+#define PLLDIV5 0x164
+#define PLLDIV6 0x168
+#define PLLDIV7 0x16c
+#define PLLDIV8 0x170
+#define PLLDIV9 0x174
+
+#define PLLCTL_PLLEN BIT(0)
+#define PLLCTL_PLLPWRDN BIT(1)
+#define PLLCTL_PLLRST BIT(3)
+#define PLLCTL_PLLDIS BIT(4)
+#define PLLCTL_PLLENSRC BIT(5)
+#define PLLCTL_CLKMODE BIT(8)
+
+/* shared by most *DIV registers */
+#define DIV_RATIO_SHIFT 0
+#define DIV_RATIO_WIDTH 5
+#define DIV_ENABLE_SHIFT 15
+
+#define PLLCMD_GOSET BIT(0)
+#define PLLSTAT_GOSTAT BIT(0)
+
+#define CKEN_OBSCLK_SHIFT 1
+#define CKEN_AUXEN_SHIFT 0
+
+/*
+ * OMAP-L138 system reference guide recommends a wait for 4 OSCIN/CLKIN
+ * cycles to ensure that the PLLC has switched to bypass mode. Delay of 1us
+ * ensures we are good for all > 4MHz OSCIN/CLKIN inputs. Typically the input
+ * is ~25MHz. Units are micro seconds.
+ */
+#define PLL_BYPASS_TIME 1
+
+/* From OMAP-L138 datasheet table 6-4. Units are micro seconds */
+#define PLL_RESET_TIME 1
+
+/*
+ * From OMAP-L138 datasheet table 6-4; assuming prediv = 1, sqrt(pllm) = 4
+ * Units are micro seconds.
+ */
+#define PLL_LOCK_TIME 20
+
+/**
+ * struct davinci_pll_clk - Main PLL clock (aka PLLOUT)
+ * @hw: clk_hw for the pll
+ * @base: Base memory address
+ * @pllm_min: The minimum allowable PLLM[PLLM] value
+ * @pllm_max: The maxiumum allowable PLLM[PLLM] value
+ * @pllm_mask: Bitmask for PLLM[PLLM] value
+ */
+struct davinci_pll_clk {
+ struct clk_hw hw;
+ void __iomem *base;
+ u32 pllm_min;
+ u32 pllm_max;
+ u32 pllm_mask;
+};
+
+#define to_davinci_pll_clk(_hw) \
+ container_of((_hw), struct davinci_pll_clk, hw)
+
+static unsigned long davinci_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct davinci_pll_clk *pll = to_davinci_pll_clk(hw);
+ unsigned long rate = parent_rate;
+ u32 mult;
+
+ mult = readl(pll->base + PLLM) & pll->pllm_mask;
+ rate *= mult + 1;
+
+ return rate;
+}
+
+static int davinci_pll_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct davinci_pll_clk *pll = to_davinci_pll_clk(hw);
+ struct clk_hw *parent = req->best_parent_hw;
+ unsigned long parent_rate = req->best_parent_rate;
+ unsigned long rate = req->rate;
+ unsigned long best_rate, r;
+ u32 mult;
+
+ /* there is a limited range of valid outputs (see datasheet) */
+ if (rate < req->min_rate)
+ return -EINVAL;
+
+ rate = min(rate, req->max_rate);
+ mult = rate / parent_rate;
+ best_rate = parent_rate * mult;
+
+ /* easy case when there is no PREDIV */
+ if (!(clk_hw_get_flags(hw) & CLK_SET_RATE_PARENT)) {
+ if (best_rate < req->min_rate)
+ return -EINVAL;
+
+ if (mult < pll->pllm_min || mult > pll->pllm_max)
+ return -EINVAL;
+
+ req->rate = best_rate;
+
+ return 0;
+ }
+
+ /* see if the PREDIV clock can help us */
+ best_rate = 0;
+
+ for (mult = pll->pllm_min; mult <= pll->pllm_max; mult++) {
+ parent_rate = clk_hw_round_rate(parent, rate / mult);
+ r = parent_rate * mult;
+ if (r < req->min_rate)
+ continue;
+ if (r > rate || r > req->max_rate)
+ break;
+ if (r > best_rate) {
+ best_rate = r;
+ req->rate = best_rate;
+ req->best_parent_rate = parent_rate;
+ if (best_rate == rate)
+ break;
+ }
+ }
+
+ return 0;
+}
+
+static int davinci_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct davinci_pll_clk *pll = to_davinci_pll_clk(hw);
+ u32 mult;
+
+ mult = rate / parent_rate;
+ writel(mult - 1, pll->base + PLLM);
+
+ return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static int davinci_pll_debug_init(struct clk_hw *hw, struct dentry *dentry);
+#else
+#define davinci_pll_debug_init NULL
+#endif
+
+static const struct clk_ops davinci_pll_ops = {
+ .recalc_rate = davinci_pll_recalc_rate,
+ .determine_rate = davinci_pll_determine_rate,
+ .set_rate = davinci_pll_set_rate,
+ .debug_init = davinci_pll_debug_init,
+};
+
+/* PLLM works differently on DM365 */
+static unsigned long dm365_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct davinci_pll_clk *pll = to_davinci_pll_clk(hw);
+ unsigned long rate = parent_rate;
+ u32 mult;
+
+ mult = readl(pll->base + PLLM) & pll->pllm_mask;
+ rate *= mult * 2;
+
+ return rate;
+}
+
+static const struct clk_ops dm365_pll_ops = {
+ .recalc_rate = dm365_pll_recalc_rate,
+ .debug_init = davinci_pll_debug_init,
+};
+
+/**
+ * davinci_pll_div_register - common *DIV clock implementation
+ * @name: the clock name
+ * @parent_name: the parent clock name
+ * @reg: the *DIV register
+ * @fixed: if true, the divider is a fixed value
+ * @flags: bitmap of CLK_* flags from clock-provider.h
+ */
+static struct clk *davinci_pll_div_register(struct device *dev,
+ const char *name,
+ const char *parent_name,
+ void __iomem *reg,
+ bool fixed, u32 flags)
+{
+ const char * const *parent_names = parent_name ? &parent_name : NULL;
+ int num_parents = parent_name ? 1 : 0;
+ const struct clk_ops *divider_ops = &clk_divider_ops;
+ struct clk_gate *gate;
+ struct clk_divider *divider;
+
+ gate = devm_kzalloc(dev, sizeof(*gate), GFP_KERNEL);
+ if (!gate)
+ return ERR_PTR(-ENOMEM);
+
+ gate->reg = reg;
+ gate->bit_idx = DIV_ENABLE_SHIFT;
+
+ divider = devm_kzalloc(dev, sizeof(*divider), GFP_KERNEL);
+ if (!divider)
+ return ERR_PTR(-ENOMEM);
+
+ divider->reg = reg;
+ divider->shift = DIV_RATIO_SHIFT;
+ divider->width = DIV_RATIO_WIDTH;
+
+ if (fixed) {
+ divider->flags |= CLK_DIVIDER_READ_ONLY;
+ divider_ops = &clk_divider_ro_ops;
+ }
+
+ return clk_register_composite(dev, name, parent_names, num_parents,
+ NULL, NULL, ÷r->hw, divider_ops,
+ &gate->hw, &clk_gate_ops, flags);
+}
+
+struct davinci_pllen_clk {
+ struct clk_hw hw;
+ void __iomem *base;
+};
+
+#define to_davinci_pllen_clk(_hw) \
+ container_of((_hw), struct davinci_pllen_clk, hw)
+
+static const struct clk_ops davinci_pllen_ops = {
+ /* this clocks just uses the clock notification feature */
+};
+
+/*
+ * The PLL has to be switched into bypass mode while we are chaning the rate,
+ * so we do that on the PLLEN clock since it is the end of the line. This will
+ * switch to bypass before any of the parent clocks (PREDIV, PLL, POSTDIV) are
+ * changed and will switch back to the PLL after the changes have been made.
+ */
+static int davinci_pllen_rate_change(struct notifier_block *nb,
+ unsigned long flags, void *data)
+{
+ struct clk_notifier_data *cnd = data;
+ struct clk_hw *hw = __clk_get_hw(cnd->clk);
+ struct davinci_pllen_clk *pll = to_davinci_pllen_clk(hw);
+ u32 ctrl;
+
+ ctrl = readl(pll->base + PLLCTL);
+
+ if (flags == PRE_RATE_CHANGE) {
+ /* Switch the PLL to bypass mode */
+ ctrl &= ~(PLLCTL_PLLENSRC | PLLCTL_PLLEN);
+ writel(ctrl, pll->base + PLLCTL);
+
+ udelay(PLL_BYPASS_TIME);
+
+ /* Reset and enable PLL */
+ ctrl &= ~(PLLCTL_PLLRST | PLLCTL_PLLDIS);
+ writel(ctrl, pll->base + PLLCTL);
+ } else {
+ udelay(PLL_RESET_TIME);
+
+ /* Bring PLL out of reset */
+ ctrl |= PLLCTL_PLLRST;
+ writel(ctrl, pll->base + PLLCTL);
+
+ udelay(PLL_LOCK_TIME);
+
+ /* Remove PLL from bypass mode */
+ ctrl |= PLLCTL_PLLEN;
+ writel(ctrl, pll->base + PLLCTL);
+ }
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block davinci_pllen_notifier = {
+ .notifier_call = davinci_pllen_rate_change,
+};
+
+/**
+ * davinci_pll_clk_register - Register a PLL clock
+ * @info: The device-specific clock info
+ * @parent_name: The parent clock name
+ * @base: The PLL's memory region
+ *
+ * This creates a series of clocks that represent the PLL.
+ *
+ * OSCIN > [PREDIV >] PLL > [POSTDIV >] PLLEN
+ *
+ * - OSCIN is the parent clock (on secondary PLL, may come from primary PLL)
+ * - PREDIV and POSTDIV are optional (depends on the PLL controller)
+ * - PLL is the PLL output (aka PLLOUT)
+ * - PLLEN is the bypass multiplexer
+ *
+ * Returns: The PLLOUT clock or a negative error code.
+ */
+struct clk *davinci_pll_clk_register(struct device *dev,
+ const struct davinci_pll_clk_info *info,
+ const char *parent_name,
+ void __iomem *base)
+{
+ char prediv_name[MAX_NAME_SIZE];
+ char pllout_name[MAX_NAME_SIZE];
+ char postdiv_name[MAX_NAME_SIZE];
+ char pllen_name[MAX_NAME_SIZE];
+ struct clk_init_data init;
+ struct davinci_pll_clk *pllout;
+ struct davinci_pllen_clk *pllen;
+ struct clk *pllout_clk, *clk;
+
+ if (info->flags & PLL_HAS_CLKMODE) {
+ /*
+ * If a PLL has PLLCTL[CLKMODE], then it is the primary PLL.
+ * We register a clock named "oscin" that serves as the internal
+ * "input clock" domain shared by both PLLs (if there are 2)
+ * and will be the parent clock to the AUXCLK, SYSCLKBP and
+ * OBSCLK domains. NB: The various TRMs use "OSCIN" to mean
+ * a number of different things. In this driver we use it to
+ * mean the signal after the PLLCTL[CLKMODE] switch.
+ */
+ clk = clk_register_fixed_factor(dev, OSCIN_CLK_NAME,
+ parent_name, 0, 1, 1);
+ if (IS_ERR(clk))
+ return clk;
+
+ parent_name = OSCIN_CLK_NAME;
+ }
+
+ if (info->flags & PLL_HAS_PREDIV) {
+ bool fixed = info->flags & PLL_PREDIV_FIXED_DIV;
+ u32 flags = 0;
+
+ snprintf(prediv_name, MAX_NAME_SIZE, "%s_prediv", info->name);
+
+ if (info->flags & PLL_PREDIV_ALWAYS_ENABLED)
+ flags |= CLK_IS_CRITICAL;
+
+ /* Some? DM355 chips don't correctly report the PREDIV value */
+ if (info->flags & PLL_PREDIV_FIXED8)
+ clk = clk_register_fixed_factor(dev, prediv_name,
+ parent_name, flags, 1, 8);
+ else
+ clk = davinci_pll_div_register(dev, prediv_name,
+ parent_name, base + PREDIV, fixed, flags);
+ if (IS_ERR(clk))
+ return clk;
+
+ parent_name = prediv_name;
+ }
+
+ /* Unlock writing to PLL registers */
+ if (info->unlock_reg) {
+ struct regmap *cfgchip;
+
+ cfgchip = syscon_regmap_lookup_by_compatible("ti,da830-cfgchip");
+ if (IS_ERR(cfgchip))
+ dev_warn(dev, "Failed to get CFGCHIP (%ld)\n",
+ PTR_ERR(cfgchip));
+ else
+ regmap_write_bits(cfgchip, info->unlock_reg,
+ info->unlock_mask, 0);
+ }
+
+ pllout = devm_kzalloc(dev, sizeof(*pllout), GFP_KERNEL);
+ if (!pllout)
+ return ERR_PTR(-ENOMEM);
+
+ snprintf(pllout_name, MAX_NAME_SIZE, "%s_pllout", info->name);
+
+ init.name = pllout_name;
+ if (info->flags & PLL_PLLM_2X)
+ init.ops = &dm365_pll_ops;
+ else
+ init.ops = &davinci_pll_ops;
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+ init.flags = 0;
+
+ if (info->flags & PLL_HAS_PREDIV)
+ init.flags |= CLK_SET_RATE_PARENT;
+
+ pllout->hw.init = &init;
+ pllout->base = base;
+ pllout->pllm_mask = info->pllm_mask;
+ pllout->pllm_min = info->pllm_min;
+ pllout->pllm_max = info->pllm_max;
+
+ pllout_clk = devm_clk_register(dev, &pllout->hw);
+ if (IS_ERR(pllout_clk))
+ return pllout_clk;
+
+ clk_hw_set_rate_range(&pllout->hw, info->pllout_min_rate,
+ info->pllout_max_rate);
+
+ parent_name = pllout_name;
+
+ if (info->flags & PLL_HAS_POSTDIV) {
+ bool fixed = info->flags & PLL_POSTDIV_FIXED_DIV;
+ u32 flags = CLK_SET_RATE_PARENT;
+
+ snprintf(postdiv_name, MAX_NAME_SIZE, "%s_postdiv", info->name);
+
+ if (info->flags & PLL_POSTDIV_ALWAYS_ENABLED)
+ flags |= CLK_IS_CRITICAL;
+
+ clk = davinci_pll_div_register(dev, postdiv_name, parent_name,
+ base + POSTDIV, fixed, flags);
+ if (IS_ERR(clk))
+ return clk;
+
+ parent_name = postdiv_name;
+ }
+
+ pllen = devm_kzalloc(dev, sizeof(*pllout), GFP_KERNEL);
+ if (!pllen)
+ return ERR_PTR(-ENOMEM);
+
+ snprintf(pllen_name, MAX_NAME_SIZE, "%s_pllen", info->name);
+
+ init.name = pllen_name;
+ init.ops = &davinci_pllen_ops;
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+ init.flags = CLK_SET_RATE_PARENT;
+
+ pllen->hw.init = &init;
+ pllen->base = base;
+
+ clk = devm_clk_register(dev, &pllen->hw);
+ if (IS_ERR(clk))
+ return clk;
+
+ clk_notifier_register(clk, &davinci_pllen_notifier);
+
+ return pllout_clk;
+}
+
+/**
+ * davinci_pll_auxclk_register - Register bypass clock (AUXCLK)
+ * @name: The clock name
+ * @base: The PLL memory region
+ */
+struct clk *davinci_pll_auxclk_register(struct device *dev,
+ const char *name,
+ void __iomem *base)
+{
+ return clk_register_gate(dev, name, OSCIN_CLK_NAME, 0, base + CKEN,
+ CKEN_AUXEN_SHIFT, 0, NULL);
+}
+
+/**
+ * davinci_pll_sysclkbp_clk_register - Register bypass divider clock (SYSCLKBP)
+ * @name: The clock name
+ * @base: The PLL memory region
+ */
+struct clk *davinci_pll_sysclkbp_clk_register(struct device *dev,
+ const char *name,
+ void __iomem *base)
+{
+ return clk_register_divider(dev, name, OSCIN_CLK_NAME, 0, base + BPDIV,
+ DIV_RATIO_SHIFT, DIV_RATIO_WIDTH,
+ CLK_DIVIDER_READ_ONLY, NULL);
+}
+
+/**
+ * davinci_pll_obsclk_register - Register oscillator divider clock (OBSCLK)
+ * @info: The clock info
+ * @base: The PLL memory region
+ */
+struct clk *
+davinci_pll_obsclk_register(struct device *dev,
+ const struct davinci_pll_obsclk_info *info,
+ void __iomem *base)
+{
+ struct clk_mux *mux;
+ struct clk_gate *gate;
+ struct clk_divider *divider;
+ u32 oscdiv;
+
+ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
+ if (!mux)
+ return ERR_PTR(-ENOMEM);
+
+ mux->reg = base + OCSEL;
+ mux->table = info->table;
+ mux->mask = info->ocsrc_mask;
+
+ gate = devm_kzalloc(dev, sizeof(*gate), GFP_KERNEL);
+ if (!gate)
+ return ERR_PTR(-ENOMEM);
+
+ gate->reg = base + CKEN;
+ gate->bit_idx = CKEN_OBSCLK_SHIFT;
+
+ divider = devm_kzalloc(dev, sizeof(*divider), GFP_KERNEL);
+ if (!divider)
+ return ERR_PTR(-ENOMEM);
+
+ divider->reg = base + OSCDIV;
+ divider->shift = DIV_RATIO_SHIFT;
+ divider->width = DIV_RATIO_WIDTH;
+
+ /* make sure divider is enabled just in case bootloader disabled it */
+ oscdiv = readl(base + OSCDIV);
+ oscdiv |= BIT(DIV_ENABLE_SHIFT);
+ writel(oscdiv, base + OSCDIV);
+
+ return clk_register_composite(dev, info->name, info->parent_names,
+ info->num_parents,
+ &mux->hw, &clk_mux_ops,
+ ÷r->hw, &clk_divider_ops,
+ &gate->hw, &clk_gate_ops, 0);
+}
+
+/* The PLL SYSCLKn clocks have a mechanism for synchronizing rate changes. */
+static int davinci_pll_sysclk_rate_change(struct notifier_block *nb,
+ unsigned long flags, void *data)
+{
+ struct clk_notifier_data *cnd = data;
+ struct clk_hw *hw = __clk_get_hw(clk_get_parent(cnd->clk));
+ struct davinci_pllen_clk *pll = to_davinci_pllen_clk(hw);
+ u32 pllcmd, pllstat;
+
+ switch (flags) {
+ case POST_RATE_CHANGE:
+ /* apply the changes */
+ pllcmd = readl(pll->base + PLLCMD);
+ pllcmd |= PLLCMD_GOSET;
+ writel(pllcmd, pll->base + PLLCMD);
+ /* fallthrough */
+ case PRE_RATE_CHANGE:
+ /* Wait until for outstanding changes to take effect */
+ do {
+ pllstat = readl(pll->base + PLLSTAT);
+ } while (pllstat & PLLSTAT_GOSTAT);
+ break;
+ }
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block davinci_pll_sysclk_notifier = {
+ .notifier_call = davinci_pll_sysclk_rate_change,
+};
+
+/**
+ * davinci_pll_sysclk_register - Register divider clocks (SYSCLKn)
+ * @info: The clock info
+ * @base: The PLL memory region
+ */
+struct clk *
+davinci_pll_sysclk_register(struct device *dev,
+ const struct davinci_pll_sysclk_info *info,
+ void __iomem *base)
+{
+ const struct clk_ops *divider_ops = &clk_divider_ops;
+ struct clk_gate *gate;
+ struct clk_divider *divider;
+ struct clk *clk;
+ u32 reg;
+ u32 flags = 0;
+
+ /* PLLDIVn registers are not entirely consecutive */
+ if (info->id < 4)
+ reg = PLLDIV1 + 4 * (info->id - 1);
+ else
+ reg = PLLDIV4 + 4 * (info->id - 4);
+
+ gate = devm_kzalloc(dev, sizeof(*gate), GFP_KERNEL);
+ if (!gate)
+ return ERR_PTR(-ENOMEM);
+
+ gate->reg = base + reg;
+ gate->bit_idx = DIV_ENABLE_SHIFT;
+
+ divider = devm_kzalloc(dev, sizeof(*divider), GFP_KERNEL);
+ if (!divider)
+ return ERR_PTR(-ENOMEM);
+
+ divider->reg = base + reg;
+ divider->shift = DIV_RATIO_SHIFT;
+ divider->width = info->ratio_width;
+ divider->flags = 0;
+
+ if (info->flags & SYSCLK_FIXED_DIV) {
+ divider->flags |= CLK_DIVIDER_READ_ONLY;
+ divider_ops = &clk_divider_ro_ops;
+ }
+
+ /* Only the ARM clock can change the parent PLL rate */
+ if (info->flags & SYSCLK_ARM_RATE)
+ flags |= CLK_SET_RATE_PARENT;
+
+ if (info->flags & SYSCLK_ALWAYS_ENABLED)
+ flags |= CLK_IS_CRITICAL;
+
+ clk = clk_register_composite(dev, info->name, &info->parent_name, 1,
+ NULL, NULL, ÷r->hw, divider_ops,
+ &gate->hw, &clk_gate_ops, flags);
+ if (IS_ERR(clk))
+ return clk;
+
+ clk_notifier_register(clk, &davinci_pll_sysclk_notifier);
+
+ return clk;
+}
+
+int of_davinci_pll_init(struct device *dev,
+ const struct davinci_pll_clk_info *info,
+ const struct davinci_pll_obsclk_info *obsclk_info,
+ const struct davinci_pll_sysclk_info *div_info,
+ u8 max_sysclk_id,
+ void __iomem *base)
+{
+ struct device_node *node = dev->of_node;
+ struct device_node *child;
+ const char *parent_name;
+ struct clk *clk;
+
+ if (info->flags & PLL_HAS_CLKMODE)
+ parent_name = of_clk_get_parent_name(node, 0);
+ else
+ parent_name = OSCIN_CLK_NAME;
+
+ clk = davinci_pll_clk_register(dev, info, parent_name, base);
+ if (IS_ERR(clk)) {
+ dev_err(dev, "failed to register %s\n", info->name);
+ return PTR_ERR(clk);
+ }
+
+ child = of_get_child_by_name(node, "pllout");
+ if (of_device_is_available(child))
+ of_clk_add_provider(child, of_clk_src_simple_get, clk);
+ of_node_put(child);
+
+ child = of_get_child_by_name(node, "sysclk");
+ if (of_device_is_available(child)) {
+ struct clk_onecell_data *clk_data;
+ struct clk **clks;
+ int n_clks = max_sysclk_id + 1;
+ int i;
+
+ clk_data = devm_kzalloc(dev, sizeof(*clk_data), GFP_KERNEL);
+ if (!clk_data)
+ return -ENOMEM;
+
+ clks = devm_kmalloc_array(dev, n_clks, sizeof(*clks), GFP_KERNEL);
+ if (!clks)
+ return -ENOMEM;
+
+ clk_data->clks = clks;
+ clk_data->clk_num = n_clks;
+
+ for (i = 0; i < n_clks; i++)
+ clks[i] = ERR_PTR(-ENOENT);
+
+ for (; div_info->name; div_info++) {
+ clk = davinci_pll_sysclk_register(dev, div_info, base);
+ if (IS_ERR(clk))
+ dev_warn(dev, "failed to register %s (%ld)\n",
+ div_info->name, PTR_ERR(clk));
+ else
+ clks[div_info->id] = clk;
+ }
+ of_clk_add_provider(child, of_clk_src_onecell_get, clk_data);
+ }
+ of_node_put(child);
+
+ child = of_get_child_by_name(node, "auxclk");
+ if (of_device_is_available(child)) {
+ char child_name[MAX_NAME_SIZE];
+
+ snprintf(child_name, MAX_NAME_SIZE, "%s_auxclk", info->name);
+
+ clk = davinci_pll_auxclk_register(dev, child_name, base);
+ if (IS_ERR(clk))
+ dev_warn(dev, "failed to register %s (%ld)\n",
+ child_name, PTR_ERR(clk));
+ else
+ of_clk_add_provider(child, of_clk_src_simple_get, clk);
+ }
+ of_node_put(child);
+
+ child = of_get_child_by_name(node, "obsclk");
+ if (of_device_is_available(child)) {
+ if (obsclk_info)
+ clk = davinci_pll_obsclk_register(dev, obsclk_info, base);
+ else
+ clk = ERR_PTR(-EINVAL);
+
+ if (IS_ERR(clk))
+ dev_warn(dev, "failed to register obsclk (%ld)\n",
+ PTR_ERR(clk));
+ else
+ of_clk_add_provider(child, of_clk_src_simple_get, clk);
+ }
+ of_node_put(child);
+
+ return 0;
+}
+
+static const struct of_device_id davinci_pll_of_match[] = {
+ { }
+};
+
+static const struct platform_device_id davinci_pll_id_table[] = {
+ { }
+};
+
+typedef int (*davinci_pll_init)(struct device *dev, void __iomem *base);
+
+static int davinci_pll_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *of_id;
+ davinci_pll_init pll_init = NULL;
+ struct resource *res;
+ void __iomem *base;
+
+ of_id = of_match_device(davinci_pll_of_match, dev);
+ if (of_id)
+ pll_init = of_id->data;
+ else if (pdev->id_entry)
+ pll_init = (void *)pdev->id_entry->driver_data;
+
+ if (!pll_init) {
+ dev_err(dev, "unable to find driver data\n");
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base)) {
+ dev_err(dev, "ioremap failed\n");
+ return PTR_ERR(base);
+ }
+
+ return pll_init(dev, base);
+}
+
+static struct platform_driver davinci_pll_driver = {
+ .probe = davinci_pll_probe,
+ .driver = {
+ .name = "davinci-pll-clk",
+ .of_match_table = davinci_pll_of_match,
+ },
+ .id_table = davinci_pll_id_table,
+};
+
+static int __init davinci_pll_driver_init(void)
+{
+ return platform_driver_register(&davinci_pll_driver);
+}
+
+/* has to be postcore_initcall because PSC devices depend on PLL parent clocks */
+postcore_initcall(davinci_pll_driver_init);
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+
+#define DEBUG_REG(n) \
+{ \
+ .name = #n, \
+ .offset = n, \
+}
+
+static const struct debugfs_reg32 davinci_pll_regs[] = {
+ DEBUG_REG(REVID),
+ DEBUG_REG(PLLCTL),
+ DEBUG_REG(OCSEL),
+ DEBUG_REG(PLLSECCTL),
+ DEBUG_REG(PLLM),
+ DEBUG_REG(PREDIV),
+ DEBUG_REG(PLLDIV1),
+ DEBUG_REG(PLLDIV2),
+ DEBUG_REG(PLLDIV3),
+ DEBUG_REG(OSCDIV),
+ DEBUG_REG(POSTDIV),
+ DEBUG_REG(BPDIV),
+ DEBUG_REG(PLLCMD),
+ DEBUG_REG(PLLSTAT),
+ DEBUG_REG(ALNCTL),
+ DEBUG_REG(DCHANGE),
+ DEBUG_REG(CKEN),
+ DEBUG_REG(CKSTAT),
+ DEBUG_REG(SYSTAT),
+ DEBUG_REG(PLLDIV4),
+ DEBUG_REG(PLLDIV5),
+ DEBUG_REG(PLLDIV6),
+ DEBUG_REG(PLLDIV7),
+ DEBUG_REG(PLLDIV8),
+ DEBUG_REG(PLLDIV9),
+};
+
+static int davinci_pll_debug_init(struct clk_hw *hw, struct dentry *dentry)
+{
+ struct davinci_pll_clk *pll = to_davinci_pll_clk(hw);
+ struct debugfs_regset32 *regset;
+ struct dentry *d;
+
+ regset = kzalloc(sizeof(regset), GFP_KERNEL);
+ if (!regset)
+ return -ENOMEM;
+
+ regset->regs = davinci_pll_regs;
+ regset->nregs = ARRAY_SIZE(davinci_pll_regs);
+ regset->base = pll->base;
+
+ d = debugfs_create_regset32("registers", 0400, dentry, regset);
+ if (IS_ERR(d)) {
+ kfree(regset);
+ return PTR_ERR(d);
+ }
+
+ return 0;
+}
+#endif
new file mode 100644
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Clock driver for TI Davinci PSC controllers
+ *
+ * Copyright (C) 2018 David Lechner <david@lechnology.com>
+ */
+
+#ifndef __CLK_DAVINCI_PLL_H___
+#define __CLK_DAVINCI_PLL_H___
+
+#include <linux/bitops.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/types.h>
+
+#define PLL_HAS_CLKMODE BIT(0) /* PLL has PLLCTL[CLKMODE] */
+#define PLL_HAS_PREDIV BIT(1) /* has prediv before PLL */
+#define PLL_PREDIV_ALWAYS_ENABLED BIT(2) /* don't clear DEN bit */
+#define PLL_PREDIV_FIXED_DIV BIT(3) /* fixed divider value */
+#define PLL_HAS_POSTDIV BIT(4) /* has postdiv after PLL */
+#define PLL_POSTDIV_ALWAYS_ENABLED BIT(5) /* don't clear DEN bit */
+#define PLL_POSTDIV_FIXED_DIV BIT(6) /* fixed divider value */
+#define PLL_HAS_EXTCLKSRC BIT(7) /* has selectable bypass */
+#define PLL_PLLM_2X BIT(8) /* PLLM value is 2x (DM365) */
+#define PLL_PREDIV_FIXED8 BIT(9) /* DM355 quirk */
+
+/** davinci_pll_clk_info - controller-specific PLL info
+ * @name: The name of the PLL
+ * @unlock_reg: Option CFGCHIP register for unlocking PLL
+ * @unlock_mask: Bitmask used with @unlock_reg
+ * @pllm_mask: Bitmask for PLLM[PLLM] value
+ * @pllm_min: Minimum allowable value for PLLM[PLLM]
+ * @pllm_max: Maximum allowable value for PLLM[PLLM]
+ * @pllout_min_rate: Minimum allowable rate for PLLOUT
+ * @pllout_max_rate: Maximum allowable rate for PLLOUT
+ * @flags: Bitmap of PLL_* flags.
+ */
+struct davinci_pll_clk_info {
+ const char *name;
+ u32 unlock_reg;
+ u32 unlock_mask;
+ u32 pllm_mask;
+ u32 pllm_min;
+ u32 pllm_max;
+ unsigned long pllout_min_rate;
+ unsigned long pllout_max_rate;
+ u32 flags;
+};
+
+#define SYSCLK_ARM_RATE BIT(0) /* Controls ARM rate */
+#define SYSCLK_ALWAYS_ENABLED BIT(1) /* Or bad things happen */
+#define SYSCLK_FIXED_DIV BIT(2) /* Fixed divider */
+
+/** davinci_pll_sysclk_info - SYSCLKn-specific info
+ * @name: The name of the clock
+ * @parent_name: The name of the parent clock
+ * @id: "n" in "SYSCLKn"
+ * @ratio_width: Width (in bits) of RATIO in PLLDIVn register
+ * @flags: Bitmap of SYSCLK_* flags.
+ */
+struct davinci_pll_sysclk_info {
+ const char *name;
+ const char *parent_name;
+ u32 id;
+ u32 ratio_width;
+ u32 flags;
+};
+
+#define SYSCLK(i, n, p, w, f) \
+{ \
+ .name = #n, \
+ .parent_name = #p, \
+ .id = (i), \
+ .ratio_width = (w), \
+ .flags = (f), \
+}
+
+/** davinci_pll_obsclk_info - OBSCLK-specific info
+ * @name: The name of the clock
+ * @parent_names: Array of names of the parent clocks
+ * @num_parents: Length of @parent_names
+ * @table: Array of values to write to OCSEL[OCSRC] cooresponding to
+ * @parent_names
+ * @ocsrc_mask: Bitmask for OCSEL[OCSRC]
+ */
+struct davinci_pll_obsclk_info {
+ const char *name;
+ const char * const *parent_names;
+ u8 num_parents;
+ u32 *table;
+ u32 ocsrc_mask;
+};
+
+struct clk *davinci_pll_clk_register(struct device *dev,
+ const struct davinci_pll_clk_info *info,
+ const char *parent_name,
+ void __iomem *base);
+struct clk *davinci_pll_auxclk_register(struct device *dev,
+ const char *name,
+ void __iomem *base);
+struct clk *davinci_pll_sysclkbp_clk_register(struct device *dev,
+ const char *name,
+ void __iomem *base);
+struct clk *
+davinci_pll_obsclk_register(struct device *dev,
+ const struct davinci_pll_obsclk_info *info,
+ void __iomem *base);
+struct clk *
+davinci_pll_sysclk_register(struct device *dev,
+ const struct davinci_pll_sysclk_info *info,
+ void __iomem *base);
+
+int of_davinci_pll_init(struct device *dev,
+ const struct davinci_pll_clk_info *info,
+ const struct davinci_pll_obsclk_info *obsclk_info,
+ const struct davinci_pll_sysclk_info *div_info,
+ u8 max_sysclk_id,
+ void __iomem *base);
+
+#endif /* __CLK_DAVINCI_PLL_H___ */
This adds a new driver for mach-davinci PLL clocks. This is porting the code from arch/arm/mach-davinci/clock.c to the common clock framework. Additionally, it adds device tree support for these clocks. The ifeq ($(CONFIG_COMMON_CLK), y) in the Makefile is needed to prevent compile errors until the clock code in arch/arm/mach-davinci is removed. Note: although there are similar clocks for TI Keystone we are not able to share the code for a few reasons. The keystone clocks are device tree only and use legacy one-node-per-clock bindings. Also the register layouts are a bit different, which would add even more if/else mess to the keystone clocks. And the keystone PLL driver doesn't support setting clock rates. Signed-off-by: David Lechner <david@lechnology.com> --- v7 changes: - convert to platform device driver - rename PLL_HAS_OSCIN to PLL_HAS_CLKMODE - add comments to clarify which clock domain "oscin" is v6 changes: - Added R: Sekhar Nori <nsekhar@ti.com> to MAINTAINERS - Split main PLL clock into oscdiv, prediv, pllout, postdiv and pllen clocks - Added min/max rate checking for pllout in set_rate - Added min/max PLLM value checking for pllout in set_rate - Fixed sysclk set_rate (checking GOSTAT and setting GOSET) - Added *_clk_info structs for passing controller-specific info - Added quirks for optional PREDIV and POSTDIV registers - Added quirk for DM355 broken PREDIV register - Added quirk for DM365 2x PLLM register - Handle unlocking PLL registers via CFGCHIP - Use pr_fmt macro MAINTAINERS | 7 + drivers/clk/Makefile | 1 + drivers/clk/davinci/Makefile | 5 + drivers/clk/davinci/pll.c | 864 +++++++++++++++++++++++++++++++++++++++++++ drivers/clk/davinci/pll.h | 120 ++++++ 5 files changed, 997 insertions(+) create mode 100644 drivers/clk/davinci/Makefile create mode 100644 drivers/clk/davinci/pll.c create mode 100644 drivers/clk/davinci/pll.h