@@ -31,6 +31,8 @@ SoC is on the same page.
Required properties:
- compatible: should be one of:
+ - "rockchip,px30-io-voltage-domain" for px30
+ - "rockchip,px30-pmu-io-voltage-domain" for px30 pmu-domains
- "rockchip,rk3188-io-voltage-domain" for rk3188
- "rockchip,rk3228-io-voltage-domain" for rk3228
- "rockchip,rk3288-io-voltage-domain" for rk3288
@@ -51,6 +53,19 @@ a phandle the relevant regulator. All specified supplies must be able
to report their voltage. The IO Voltage Domain for any non-specified
supplies will be not be touched.
+Possible supplies for PX30:
+- vccio6-supply: The supply connected to VCCIO6.
+- vccio1-supply: The supply connected to VCCIO1.
+- vccio2-supply: The supply connected to VCCIO2.
+- vccio3-supply: The supply connected to VCCIO3.
+- vccio4-supply: The supply connected to VCCIO4.
+- vccio5-supply: The supply connected to VCCIO5.
+- vccio-oscgpi-supply: The supply connected to VCCIO_OSCGPI.
+
+Possible supplies for PX30 pmu-domains:
+- pmuio1-supply: The supply connected to PMUIO1.
+- pmuio2-supply: The supply connected to PMUIO2.
+
Possible supplies for rk3188:
- ap0-supply: The supply connected to AP0_VCC.
- ap1-supply: The supply connected to AP1_VCC.
@@ -39,6 +39,10 @@
#define MAX_VOLTAGE_1_8 1980000
#define MAX_VOLTAGE_3_3 3600000
+#define PX30_IO_VSEL 0x180
+#define PX30_IO_VSEL_VCCIO6_SRC BIT(0)
+#define PX30_IO_VSEL_VCCIO6_SUPPLY_NUM 1
+
#define RK3288_SOC_CON2 0x24c
#define RK3288_SOC_CON2_FLASH0 BIT(7)
#define RK3288_SOC_FLASH_SUPPLY_NUM 2
@@ -151,6 +155,25 @@ static int rockchip_iodomain_notify(struct notifier_block *nb,
return NOTIFY_OK;
}
+static void px30_iodomain_init(struct rockchip_iodomain *iod)
+{
+ int ret;
+ u32 val;
+
+ /* if no VCCIO0 supply we should leave things alone */
+ if (!iod->supplies[PX30_IO_VSEL_VCCIO6_SUPPLY_NUM].reg)
+ return;
+
+ /*
+ * set vccio0 iodomain to also use this framework
+ * instead of a special gpio.
+ */
+ val = PX30_IO_VSEL_VCCIO6_SRC | (PX30_IO_VSEL_VCCIO6_SRC << 16);
+ ret = regmap_write(iod->grf, PX30_IO_VSEL, val);
+ if (ret < 0)
+ dev_warn(iod->dev, "couldn't update vccio0 ctrl\n");
+}
+
static void rk3288_iodomain_init(struct rockchip_iodomain *iod)
{
int ret;
@@ -227,6 +250,43 @@ static void rk3399_pmu_iodomain_init(struct rockchip_iodomain *iod)
dev_warn(iod->dev, "couldn't update pmu io iodomain ctrl\n");
}
+static const struct rockchip_iodomain_soc_data soc_data_px30 = {
+ .grf_offset = 0x180,
+ .supply_names = {
+ NULL,
+ "vccio6",
+ "vccio1",
+ "vccio2",
+ "vccio3",
+ "vccio4",
+ "vccio5",
+ "vccio-oscgpi",
+ },
+ .init = px30_iodomain_init,
+};
+
+static const struct rockchip_iodomain_soc_data soc_data_px30_pmu = {
+ .grf_offset = 0x100,
+ .supply_names = {
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ NULL,
+ "pmuio1",
+ "pmuio2",
+ },
+};
+
/*
* On the rk3188 the io-domains are handled by a shared register with the
* lower 8 bits being still being continuing drive-strength settings.
@@ -381,6 +441,14 @@ static const struct rockchip_iodomain_soc_data soc_data_rv1108_pmu = {
static const struct of_device_id rockchip_iodomain_match[] = {
{
+ .compatible = "rockchip,px30-io-voltage-domain",
+ .data = (void *)&soc_data_px30
+ },
+ {
+ .compatible = "rockchip,px30-pmu-io-voltage-domain",
+ .data = (void *)&soc_data_px30_pmu
+ },
+ {
.compatible = "rockchip,rk3188-io-voltage-domain",
.data = &soc_data_rk3188
},
This adds the necessary data for handling io voltage domains on PX30. As interesting tidbit, the PX30 contains two separate iodomain areas. One in the regular General Register Files (GRF) and one in PMUGRF in the pmu power domain. Signed-off-by: David Wu <david.wu@rock-chips.com> --- .../bindings/power/rockchip-io-domain.txt | 15 +++++ drivers/power/avs/rockchip-io-domain.c | 68 ++++++++++++++++++++++ 2 files changed, 83 insertions(+)