diff mbox

[09/19] mmc: mmci: add variant property to write datactrl before command

Message ID 1528809280-31116-10-git-send-email-ludovic.Barre@st.com (mailing list archive)
State New, archived
Headers show

Commit Message

Ludovic BARRE June 12, 2018, 1:14 p.m. UTC 
From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 6 ++++--
 drivers/mmc/host/mmci.h | 2 ++
 2 files changed, 6 insertions(+), 2 deletions(-)
diff mbox

Patch

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 5fd3ffb6..83c3572 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -855,7 +855,8 @@  mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
 		mmci_request_end(host, host->mrq);
 	} else if (sbc) {
 		mmci_start_command(host, host->mrq->cmd, 0);
-	} else if (!(cmd->data->flags & MMC_DATA_READ)) {
+	} else if (!host->variant->datactrl_first &&
+		   !(cmd->data->flags & MMC_DATA_READ)) {
 		mmci_start_data(host, cmd->data);
 	}
 }
@@ -1119,7 +1120,8 @@  static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	if (mrq->data)
 		mmci_dma_get_next_data(host, mrq->data);
 
-	if (mrq->data && mrq->data->flags & MMC_DATA_READ)
+	if (mrq->data &&
+	    (host->variant->datactrl_first || mrq->data->flags & MMC_DATA_READ))
 		mmci_start_data(host, mrq->data);
 
 	if (mrq->sbc)
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index b91b130..5091025 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -259,6 +259,7 @@  struct mmci_host;
  * @datactrl_mask_sdio: SDIO enable mask in datactrl register
  * @datactrl_blksz: block size in power of two
  * @datactrl_dpsm_enable: enable value for DPSM
+ * @datactrl_first: true if data must be setup before send command
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -301,6 +302,7 @@  struct variant_data {
 	unsigned int		datactrl_mask_sdio;
 	unsigned int		datactrl_blocksz;
 	unsigned int		datactrl_dpsm_enable;
+	bool			datactrl_first;
 	bool			st_sdio;
 	bool			st_clkdiv;
 	bool			blksz_datactrl16;