diff mbox

[1/2] clk: uniphier: add NAND 200MHz clock

Message ID 1532075856-1723-1-git-send-email-yamada.masahiro@socionext.com (mailing list archive)
State New, archived
Headers show

Commit Message

Masahiro Yamada July 20, 2018, 8:37 a.m. UTC 
The Denali NAND controller IP needs three clocks:

 - clk: controller core clock

 - clk_x: bus interface clock

 - ecc_clk: clock at which ECC circuitry is run

Currently, only the first one (50MHz) is provided.  The rest of the
two clock ports must be connected to the 200MHz clock line.  Add this.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---

 drivers/clk/uniphier/clk-uniphier-sys.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)

Comments

Stephen Boyd July 25, 2018, 11:23 p.m. UTC | #1 
Quoting Masahiro Yamada (2018-07-20 01:37:35)
> The Denali NAND controller IP needs three clocks:
> 
>  - clk: controller core clock
> 
>  - clk_x: bus interface clock
> 
>  - ecc_clk: clock at which ECC circuitry is run
> 
> Currently, only the first one (50MHz) is provided.  The rest of the
> two clock ports must be connected to the 200MHz clock line.  Add this.
> 
> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
> ---

Applied to clk-next
diff mbox

Patch

diff --git a/drivers/clk/uniphier/clk-uniphier-sys.c b/drivers/clk/uniphier/clk-uniphier-sys.c
index 4f5ff9f..a582446 100644
--- a/drivers/clk/uniphier/clk-uniphier-sys.c
+++ b/drivers/clk/uniphier/clk-uniphier-sys.c
@@ -29,18 +29,20 @@ 
 	UNIPHIER_CLK_FACTOR("sd-200m", -1, "spll", 1, 10),		\
 	UNIPHIER_CLK_FACTOR("sd-133m", -1, "spll", 1, 15)
 
-/* Denali driver requires clk_x rate (clk: 50MHz, clk_x & ecc_clk: 200MHz) */
 #define UNIPHIER_LD4_SYS_CLK_NAND(idx)					\
-	UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 8),		\
-	UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x2104, 2)
+	UNIPHIER_CLK_FACTOR("nand-50m", -1, "spll", 1, 32),		\
+	UNIPHIER_CLK_GATE("nand", (idx), "nand-50m", 0x2104, 2)
 
 #define UNIPHIER_PRO5_SYS_CLK_NAND(idx)					\
-	UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 12),		\
-	UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x2104, 2)
+	UNIPHIER_CLK_FACTOR("nand-50m", -1, "spll", 1, 48),		\
+	UNIPHIER_CLK_GATE("nand", (idx), "nand-50m", 0x2104, 2)
 
 #define UNIPHIER_LD11_SYS_CLK_NAND(idx)					\
-	UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 10),		\
-	UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x210c, 0)
+	UNIPHIER_CLK_FACTOR("nand-50m", -1, "spll", 1, 40),		\
+	UNIPHIER_CLK_GATE("nand", (idx), "nand-50m", 0x210c, 0)
+
+#define UNIPHIER_SYS_CLK_NAND_4X(idx)					\
+	UNIPHIER_CLK_FACTOR("nand-4x", (idx), "nand", 4, 1)
 
 #define UNIPHIER_LD11_SYS_CLK_EMMC(idx)					\
 	UNIPHIER_CLK_GATE("emmc", (idx), NULL, 0x210c, 2)
@@ -94,6 +96,7 @@  const struct uniphier_clk_data uniphier_ld4_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "a2pll", 1, 16),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 16),
 	UNIPHIER_LD4_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD4_SYS_CLK_SD,
 	UNIPHIER_CLK_FACTOR("usb2", -1, "upll", 1, 12),
 	UNIPHIER_LD4_SYS_CLK_STDMAC(8),			/* Ether, HSC, MIO */
@@ -109,6 +112,7 @@  const struct uniphier_clk_data uniphier_pro4_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "a2pll", 1, 8),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 32),
 	UNIPHIER_LD4_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD4_SYS_CLK_SD,
 	UNIPHIER_CLK_FACTOR("usb2", -1, "upll", 1, 12),
 	UNIPHIER_PRO4_SYS_CLK_ETHER(6),
@@ -131,6 +135,7 @@  const struct uniphier_clk_data uniphier_sld8_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "spll", 1, 20),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 16),
 	UNIPHIER_LD4_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD4_SYS_CLK_SD,
 	UNIPHIER_CLK_FACTOR("usb2", -1, "upll", 1, 12),
 	UNIPHIER_LD4_SYS_CLK_STDMAC(8),			/* Ether, HSC, MIO */
@@ -144,6 +149,7 @@  const struct uniphier_clk_data uniphier_pro5_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "dapll2", 1, 40),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 48),
 	UNIPHIER_PRO5_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_PRO5_SYS_CLK_SD,
 	UNIPHIER_LD4_SYS_CLK_STDMAC(8),				/* HSC */
 	UNIPHIER_PRO4_SYS_CLK_GIO(12),				/* PCIe, USB3 */
@@ -159,6 +165,7 @@  const struct uniphier_clk_data uniphier_pxs2_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "spll", 1, 27),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 48),
 	UNIPHIER_PRO5_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_PRO5_SYS_CLK_SD,
 	UNIPHIER_PRO4_SYS_CLK_ETHER(6),
 	UNIPHIER_LD4_SYS_CLK_STDMAC(8),				/* HSC, RLE */
@@ -181,6 +188,7 @@  const struct uniphier_clk_data uniphier_ld11_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "spll", 1, 34),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 40),
 	UNIPHIER_LD11_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD11_SYS_CLK_EMMC(4),
 	/* Index 5 reserved for eMMC PHY */
 	UNIPHIER_LD11_SYS_CLK_ETHER(6),
@@ -214,6 +222,7 @@  const struct uniphier_clk_data uniphier_ld20_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("uart", 0, "spll", 1, 34),
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 40),
 	UNIPHIER_LD11_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD11_SYS_CLK_EMMC(4),
 	/* Index 5 reserved for eMMC PHY */
 	UNIPHIER_LD20_SYS_CLK_SD,
@@ -256,6 +265,7 @@  const struct uniphier_clk_data uniphier_pxs3_sys_clk_data[] = {
 	UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 40),
 	UNIPHIER_LD20_SYS_CLK_SD,
 	UNIPHIER_LD11_SYS_CLK_NAND(2),
+	UNIPHIER_SYS_CLK_NAND_4X(3),
 	UNIPHIER_LD11_SYS_CLK_EMMC(4),
 	UNIPHIER_CLK_GATE("ether0", 6, NULL, 0x210c, 9),
 	UNIPHIER_CLK_GATE("ether1", 7, NULL, 0x210c, 10),