| Message ID | 1536317831-58056-2-git-send-email-jianxin.pan@amlogic.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | mtd: rawnand: meson: add Amlogic NAND driver support | expand |
On Fri, 7 Sep 2018 18:57:10 +0800 Jianxin Pan <jianxin.pan@amlogic.com> wrote: > From: Liang Yang <liang.yang@amlogic.com> > > Add Amlogic NAND controller dt-bindings for Meson SoC, > Current this driver support GXBB/GXL/AXG platform. > > Signed-off-by: Liang Yang <liang.yang@amlogic.com> > Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> > --- > .../devicetree/bindings/mtd/amlogic,meson-nand.txt | 91 ++++++++++++++++++++++ > 1 file changed, 91 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt > > diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt > new file mode 100644 > index 0000000..655a778 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt > @@ -0,0 +1,91 @@ > +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs > + > +This file documents the properties in addition to those available in > +the MTD NAND bindings. > + > +Required properties: > +- compatible : contains one of: > + - "amlogic,meson-gxl-nfc" > + - "amlogic,meson-axg-nfc" > +- clocks : > + A list of phandle + clock-specifier pairs for the clocks listed > + in clock-names. > + > +- clock-names: Should contain the following: > + "core" - NFC module gate clock > + "device" - device clock from eMMC sub clock controller > + > +- pins : Select pins which NFC need. > +- nand_pins: Detail NAND pins information. You mean pinctrl-names and pinctrl-0, right? Not sure it's necessary to document that, but if you do, please use the correct DT prop names. > +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC > + controller port C > + > +Optional children nodes: > +Children nodes represent the available nand chips. > + > + > + One too many blank lines here. > +Other properties: > +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. > + > +Example demonstrate on AXG SoC: > + > + sd_emmc_c_clkc: mmc@7000 { > + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; > + reg = <0x0 0x7000 0x0 0x800>; > + status = "okay"; > + }; > + > + nand: nfc@7800 { > + compatible = "amlogic,meson-axg-nfc"; > + reg = <0x0 0x7800 0x0 0x100>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; > + status = "disabled"; > + > + clocks = <&clkc CLKID_SD_EMMC_C>, > + <&sd_emmc_c_clkc CLKID_MMC_DIV>; > + clock-names = "core", "device"; > + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; > + > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&nand_pins>; > + > + nand@0 { > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + nand-on-flash-bbt; > + nand-ecc-mode = "hw"; > + nand-ecc-strength = <8>; > + nand-ecc-step-size = <1024>; Drop nand-ecc- props. I guess you have a sensible default value and I prefer when ECC requirements are directly extracted during chip detection. Defining that in the DT is a bad habit. The only one that could make sense (assuming you support it) is nand-ecc-maximize. > + > + amlogic,nand-enable-scrambler; Please drop this property (it's not longer documented). > + > + partition@0 { > + label = "boot"; > + reg = <0x00000000 0x00200000>; > + read-only; > + }; > + partition@200000 { > + label = "env"; > + reg = <0x00200000 0x00400000>; > + }; > + partition@600000 { > + label = "system"; > + reg = <0x00600000 0x00a00000>; > + }; > + partition@1000000 { > + label = "rootfs"; > + reg = <0x01000000 0x03000000>; > + }; > + partition@4000000 { > + label = "media"; > + reg = <0x04000000 0x8000000>; > + }; No need to define the partitions in your example, especially since they should be placed in a partitions subnode with a "fixed-partitions" compat. > + }; > + };
Hi boric, Thanks for your quick reply. On 9/7/2018 8:19 PM, Boris Brezillon wrote: > On Fri, 7 Sep 2018 18:57:10 +0800 > Jianxin Pan <jianxin.pan@amlogic.com> wrote: > >> From: Liang Yang <liang.yang@amlogic.com> >> >> Add Amlogic NAND controller dt-bindings for Meson SoC, >> Current this driver support GXBB/GXL/AXG platform. >> >> Signed-off-by: Liang Yang <liang.yang@amlogic.com> >> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> >> --- >> .../devicetree/bindings/mtd/amlogic,meson-nand.txt | 91 ++++++++++++++++++++++ >> 1 file changed, 91 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt >> >> diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt >> new file mode 100644 >> index 0000000..655a778 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt >> @@ -0,0 +1,91 @@ >> +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs >> + >> +This file documents the properties in addition to those available in >> +the MTD NAND bindings. >> + >> +Required properties: >> +- compatible : contains one of: >> + - "amlogic,meson-gxl-nfc" >> + - "amlogic,meson-axg-nfc" >> +- clocks : >> + A list of phandle + clock-specifier pairs for the clocks listed >> + in clock-names. >> + >> +- clock-names: Should contain the following: >> + "core" - NFC module gate clock >> + "device" - device clock from eMMC sub clock controller >> + >> +- pins : Select pins which NFC need. >> +- nand_pins: Detail NAND pins information. > > You mean pinctrl-names and pinctrl-0, right? Not sure it's necessary to > document that, but if you do, please use the correct DT prop names. > I find no documentation for that in other xx_nand.txt; I will consider to remove it. >> +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC >> + controller port C >> + >> +Optional children nodes: >> +Children nodes represent the available nand chips. >> + >> + >> + > > One too many blank lines here. > ok, i will remove it. >> +Other properties: >> +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. >> + >> +Example demonstrate on AXG SoC: >> + >> + sd_emmc_c_clkc: mmc@7000 { >> + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; >> + reg = <0x0 0x7000 0x0 0x800>; >> + status = "okay"; >> + }; >> + >> + nand: nfc@7800 { >> + compatible = "amlogic,meson-axg-nfc"; >> + reg = <0x0 0x7800 0x0 0x100>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; >> + status = "disabled"; >> + >> + clocks = <&clkc CLKID_SD_EMMC_C>, >> + <&sd_emmc_c_clkc CLKID_MMC_DIV>; >> + clock-names = "core", "device"; >> + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; >> + >> + status = "okay"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&nand_pins>; >> + >> + nand@0 { >> + reg = <0>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + nand-on-flash-bbt; >> + nand-ecc-mode = "hw"; >> + nand-ecc-strength = <8>; >> + nand-ecc-step-size = <1024>; > > Drop nand-ecc- props. I guess you have a sensible default value and I > prefer when ECC requirements are directly extracted during chip > detection. Defining that in the DT is a bad habit. The only one that > could make sense (assuming you support it) is nand-ecc-maximize. > ok, i will drop them. we adopt auto detection during init stage, it works too. >> + >> + amlogic,nand-enable-scrambler; > > Please drop this property (it's not longer documented). > em, we should have removed it when nfc driver never use it. >> + >> + partition@0 { >> + label = "boot"; >> + reg = <0x00000000 0x00200000>; >> + read-only; >> + }; >> + partition@200000 { >> + label = "env"; >> + reg = <0x00200000 0x00400000>; >> + }; >> + partition@600000 { >> + label = "system"; >> + reg = <0x00600000 0x00a00000>; >> + }; >> + partition@1000000 { >> + label = "rootfs"; >> + reg = <0x01000000 0x03000000>; >> + }; >> + partition@4000000 { >> + label = "media"; >> + reg = <0x04000000 0x8000000>; >> + }; > > No need to define the partitions in your example, especially since they > should be placed in a partitions subnode with a "fixed-partitions" > compat. > ok, i will remove it. >> + }; >> + }; > > . >
diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt new file mode 100644 index 0000000..655a778 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt @@ -0,0 +1,91 @@ +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +This file documents the properties in addition to those available in +the MTD NAND bindings. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gxl-nfc" + - "amlogic,meson-axg-nfc" +- clocks : + A list of phandle + clock-specifier pairs for the clocks listed + in clock-names. + +- clock-names: Should contain the following: + "core" - NFC module gate clock + "device" - device clock from eMMC sub clock controller + +- pins : Select pins which NFC need. +- nand_pins: Detail NAND pins information. +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC + controller port C + +Optional children nodes: +Children nodes represent the available nand chips. + + + +Other properties: +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example demonstrate on AXG SoC: + + sd_emmc_c_clkc: mmc@7000 { + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; + reg = <0x0 0x7000 0x0 0x800>; + status = "okay"; + }; + + nand: nfc@7800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0x0 0x7800 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + status = "disabled"; + + clocks = <&clkc CLKID_SD_EMMC_C>, + <&sd_emmc_c_clkc CLKID_MMC_DIV>; + clock-names = "core", "device"; + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; + + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-strength = <8>; + nand-ecc-step-size = <1024>; + + amlogic,nand-enable-scrambler; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x00200000>; + read-only; + }; + partition@200000 { + label = "env"; + reg = <0x00200000 0x00400000>; + }; + partition@600000 { + label = "system"; + reg = <0x00600000 0x00a00000>; + }; + partition@1000000 { + label = "rootfs"; + reg = <0x01000000 0x03000000>; + }; + partition@4000000 { + label = "media"; + reg = <0x04000000 0x8000000>; + }; + }; + };