@@ -75,6 +75,14 @@ config DWMAC_LPC18XX
---help---
Support for NXP LPC18xx/43xx DWMAC Ethernet.
+config DWMAC_MEDIATEK
+ tristate "MediaTek MT27xx GMAC support"
+ depends on OF && (ARCH_MEDIATEK || COMPILE_TEST)
+ help
+ Support for MediaTek GMAC Ethernet controller.
+
+ This selects the MT2712 SoC support for the stmmac driver.
+
config DWMAC_MESON
tristate "Amlogic Meson dwmac support"
default ARCH_MESON
@@ -13,6 +13,7 @@ obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
obj-$(CONFIG_DWMAC_ANARION) += dwmac-anarion.o
obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o
obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o
+obj-$(CONFIG_DWMAC_MEDIATEK) += dwmac-mediatek.o
obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o
obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o
obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
new file mode 100644
@@ -0,0 +1,408 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ */
+#include <linux/bitfield.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_net.h>
+#include <linux/regmap.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+/* Peri Configuration register for mt2712 */
+#define PERI_ETH_PHY_INTF_SEL 0x418
+#define PHY_INTF_MII 0
+#define PHY_INTF_RGMII 1
+#define PHY_INTF_RMII 4
+#define RMII_CLK_SRC_RXC BIT(4)
+#define RMII_CLK_SRC_INTERNAL BIT(5)
+
+#define PERI_ETH_DLY 0x428
+#define ETH_DLY_GTXC_INV BIT(6)
+#define ETH_DLY_GTXC_ENABLE BIT(5)
+#define ETH_DLY_GTXC_STAGES GENMASK(4, 0)
+#define ETH_DLY_TXC_INV BIT(20)
+#define ETH_DLY_TXC_ENABLE BIT(19)
+#define ETH_DLY_TXC_STAGES GENMASK(18, 14)
+#define ETH_DLY_RXC_INV BIT(13)
+#define ETH_DLY_RXC_ENABLE BIT(12)
+#define ETH_DLY_RXC_STAGES GENMASK(11, 7)
+
+#define PERI_ETH_DLY_FINE 0x800
+#define ETH_RMII_DLY_TX_INV BIT(2)
+#define ETH_FINE_DLY_GTXC BIT(1)
+#define ETH_FINE_DLY_RXC BIT(0)
+
+struct mac_delay_struct {
+ u32 tx_delay;
+ u32 rx_delay;
+ bool tx_inv;
+ bool rx_inv;
+ bool fine_tune;
+};
+
+struct mediatek_dwmac_plat_data {
+ const struct mediatek_dwmac_variant *variant;
+ struct mac_delay_struct mac_delay;
+ struct clk_bulk_data *clks;
+ struct device_node *np;
+ struct regmap *peri_regmap;
+ struct device *dev;
+ int phy_mode;
+ bool rmii_rxc;
+};
+
+struct mediatek_dwmac_variant {
+ int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
+ int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
+
+ /* clock ids to be requested */
+ const char * const *clk_list;
+ int num_clks;
+
+ u32 dma_bit_mask;
+ u32 rx_delay_max;
+ u32 tx_delay_max;
+};
+
+/* list of clocks required for mac */
+static const char * const mt2712_dwmac_clk_l[] = {
+ "axi", "apb", "mac_main", "ptp_ref"
+};
+
+static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
+{
+ int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
+ u32 intf_val = 0;
+
+ /* select phy interface in top control domain */
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ intf_val |= PHY_INTF_MII;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ intf_val |= (PHY_INTF_RMII | rmii_rxc);
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ intf_val |= PHY_INTF_RGMII;
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ regmap_write(plat->peri_regmap, PERI_ETH_PHY_INTF_SEL, intf_val);
+
+ return 0;
+}
+
+static void mt2712_delay_ps2stage(struct mac_delay_struct *mac_delay)
+{
+ if (mac_delay->fine_tune) {
+ /* 170ps per stage for fine tune delay macro circuit*/
+ mac_delay->tx_delay /= 170;
+ mac_delay->rx_delay /= 170;
+ } else {
+ /* 550ps per stage for coarse tune delay macro circuit*/
+ mac_delay->tx_delay /= 550;
+ mac_delay->rx_delay /= 550;
+ }
+}
+
+static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 delay_val = 0, fine_val = 0;
+
+ mt2712_delay_ps2stage(mac_delay);
+
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ /* the rmii reference clock is from external phy,
+ * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+ * the reference clk is connected to. The reference clock is a
+ * received signal, so rx_delay/rx_inv are used to indicate
+ * the reference clock timing adjustment
+ */
+ if (plat->rmii_rxc) {
+ /* the rmii reference clock from outside is connected
+ * to RXC pin, the reference clock will be adjusted
+ * by RXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+ } else {
+ /* the rmii reference clock from outside is connected
+ * to TXC pin, the reference clock will be adjusted
+ * by TXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv);
+ }
+ /* tx_inv will inverse the tx clock inside mac relateive to
+ * reference clock from external phy,
+ * and this bit is located in the same register with fine-tune
+ */
+ if (mac_delay->tx_inv)
+ fine_val = ETH_RMII_DLY_TX_INV;
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ /* the PHY is not responsible for inserting any internal
+ * delay by itself in PHY_INTERFACE_MODE_RGMII case,
+ * so Ethernet MAC will insert delays for both transmit
+ * and receive path here.
+ */
+ if (mac_delay->fine_tune)
+ fine_val = ETH_FINE_DLY_GTXC | ETH_FINE_DLY_RXC;
+
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ /* the PHY should insert an internal delay for the transmit
+ * path in PHY_INTERFACE_MODE_RGMII_TXID case,
+ * so Ethernet MAC will insert the delay for receive path here.
+ */
+ if (mac_delay->fine_tune)
+ fine_val = ETH_FINE_DLY_RXC;
+
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ /* the PHY should insert an internal delay for the receive
+ * path in PHY_INTERFACE_MODE_RGMII_RXID case,
+ * so Ethernet MAC will insert the delay for transmit path here.
+ */
+ if (mac_delay->fine_tune)
+ fine_val = ETH_FINE_DLY_GTXC;
+
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ /* the PHY should insert internal delays for both transmit
+ * and receive path in PHY_INTERFACE_MODE_RGMII_RXID case,
+ * so Ethernet MAC will NOT insert any delay here.
+ */
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+ regmap_write(plat->peri_regmap, PERI_ETH_DLY, delay_val);
+ regmap_write(plat->peri_regmap, PERI_ETH_DLY_FINE, fine_val);
+
+ return 0;
+}
+
+static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
+ .dwmac_set_phy_interface = mt2712_set_interface,
+ .dwmac_set_delay = mt2712_set_delay,
+ .clk_list = mt2712_dwmac_clk_l,
+ .num_clks = ARRAY_SIZE(mt2712_dwmac_clk_l),
+ .dma_bit_mask = 33,
+ .rx_delay_max = 17600,
+ .tx_delay_max = 17600,
+};
+
+static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 tx_delay_ps, rx_delay_ps;
+
+ plat->peri_regmap = syscon_regmap_lookup_by_phandle(plat->np, "mediatek,pericfg");
+ if (IS_ERR(plat->peri_regmap)) {
+ dev_err(plat->dev, "Failed to get pericfg syscon\n");
+ return PTR_ERR(plat->peri_regmap);
+ }
+
+ plat->phy_mode = of_get_phy_mode(plat->np);
+ if (plat->phy_mode < 0) {
+ dev_err(plat->dev, "not find phy-mode\n");
+ return -EINVAL;
+ }
+
+ if (!of_property_read_u32(plat->np, "mediatek,tx-delay-ps", &tx_delay_ps)) {
+ if (tx_delay_ps < plat->variant->tx_delay_max) {
+ mac_delay->tx_delay = tx_delay_ps;
+ } else {
+ dev_err(plat->dev, "Invalid TX clock delay: %dps\n", tx_delay_ps);
+ return -EINVAL;
+ }
+ }
+
+ if (!of_property_read_u32(plat->np, "mediatek,rx-delay-ps", &rx_delay_ps)) {
+ if (rx_delay_ps < plat->variant->rx_delay_max) {
+ mac_delay->rx_delay = rx_delay_ps;
+ } else {
+ dev_err(plat->dev, "Invalid RX clock delay: %dps\n", rx_delay_ps);
+ return -EINVAL;
+ }
+ }
+
+ mac_delay->tx_inv = of_property_read_bool(plat->np, "mediatek,txc-inverse");
+ mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
+ mac_delay->fine_tune = of_property_read_bool(plat->np, "mediatek,fine-tune");
+ plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
+
+ return 0;
+}
+
+static int mediatek_dwmac_clk_init(struct mediatek_dwmac_plat_data *plat)
+{
+ const struct mediatek_dwmac_variant *variant = plat->variant;
+ int i, num = variant->num_clks;
+
+ plat->clks = devm_kcalloc(plat->dev, num, sizeof(*plat->clks), GFP_KERNEL);
+ if (!plat->clks)
+ return -ENOMEM;
+
+ for (i = 0; i < num; i++)
+ plat->clks[i].id = variant->clk_list[i];
+
+ return devm_clk_bulk_get(plat->dev, num, plat->clks);
+}
+
+static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
+{
+ struct mediatek_dwmac_plat_data *plat = priv;
+ const struct mediatek_dwmac_variant *variant = plat->variant;
+ int ret;
+
+ ret = dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(variant->dma_bit_mask));
+ if (ret) {
+ dev_err(plat->dev, "No suitable DMA available, err = %d\n", ret);
+ return ret;
+ }
+
+ ret = variant->dwmac_set_phy_interface(plat);
+ if (ret) {
+ dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
+ return ret;
+ }
+
+ ret = variant->dwmac_set_delay(plat);
+ if (ret) {
+ dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_bulk_prepare_enable(variant->num_clks, plat->clks);
+ if (ret) {
+ dev_err(plat->dev, "failed to enable clks, err = %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct mediatek_dwmac_plat_data *plat = priv;
+ const struct mediatek_dwmac_variant *variant = plat->variant;
+
+ clk_bulk_disable_unprepare(variant->num_clks, plat->clks);
+}
+
+static int mediatek_dwmac_probe(struct platform_device *pdev)
+{
+ struct mediatek_dwmac_plat_data *priv_plat;
+ struct plat_stmmacenet_data *plat_dat;
+ struct stmmac_resources stmmac_res;
+ int ret;
+
+ priv_plat = devm_kzalloc(&pdev->dev, sizeof(*priv_plat), GFP_KERNEL);
+ if (!priv_plat)
+ return -ENOMEM;
+
+ priv_plat->variant = of_device_get_match_data(&pdev->dev);
+ if (!priv_plat->variant) {
+ dev_err(&pdev->dev, "Missing dwmac-mediatek variant\n");
+ return -EINVAL;
+ }
+
+ priv_plat->dev = &pdev->dev;
+ priv_plat->np = pdev->dev.of_node;
+
+ ret = mediatek_dwmac_config_dt(priv_plat);
+ if (ret)
+ return ret;
+
+ ret = mediatek_dwmac_clk_init(priv_plat);
+ if (ret)
+ return ret;
+
+ ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+ if (ret)
+ return ret;
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
+
+ plat_dat->interface = priv_plat->phy_mode;
+ /* clk_csr_i = 250-300MHz & MDC = clk_csr_i/124 */
+ plat_dat->clk_csr = 5;
+ plat_dat->has_gmac4 = 1;
+ plat_dat->has_gmac = 0;
+ plat_dat->pmt = 0;
+ plat_dat->maxmtu = ETH_DATA_LEN;
+ plat_dat->bsp_priv = priv_plat;
+ plat_dat->init = mediatek_dwmac_init;
+ plat_dat->exit = mediatek_dwmac_exit;
+ mediatek_dwmac_init(pdev, priv_plat);
+
+ ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+ if (ret) {
+ stmmac_remove_config_dt(pdev, plat_dat);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id mediatek_dwmac_match[] = {
+ { .compatible = "mediatek,mt2712-gmac",
+ .data = &mt2712_gmac_variant },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, mediatek_dwmac_match);
+
+static struct platform_driver mediatek_dwmac_driver = {
+ .probe = mediatek_dwmac_probe,
+ .remove = stmmac_pltfr_remove,
+ .driver = {
+ .name = "dwmac-mediatek",
+ .pm = &stmmac_pltfr_pm_ops,
+ .of_match_table = mediatek_dwmac_match,
+ },
+};
+module_platform_driver(mediatek_dwmac_driver);
Add Ethernet support for MediaTek SoCs from the mt2712 family Signed-off-by: Biao Huang <biao.huang@mediatek.com> --- drivers/net/ethernet/stmicro/stmmac/Kconfig | 8 + drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 408 ++++++++++++++++++++ 3 files changed, 417 insertions(+) create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c