diff mbox series

[5/5] ARM: dts: imx7ulp: Move usdhc clocks assignment to board DT

Message ID 1571192067-19600-5-git-send-email-Anson.Huang@nxp.com (mailing list archive)
State Mainlined
Commit 59cf1496672cd34f47f85aa1af280909e7b58762
Headers show
Series [1/5] arm64: dts: imx8qxp: Move usdhc clocks assignment to board DT | expand

Commit Message

Anson Huang Oct. 16, 2019, 2:14 a.m. UTC 
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm/boot/dts/imx7ulp-evk.dts | 2 ++
 arch/arm/boot/dts/imx7ulp.dtsi    | 4 ----
 2 files changed, 2 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx7ulp-evk.dts b/arch/arm/boot/dts/imx7ulp-evk.dts
index 4245b33..f1093d2 100644
--- a/arch/arm/boot/dts/imx7ulp-evk.dts
+++ b/arch/arm/boot/dts/imx7ulp-evk.dts
@@ -77,6 +77,8 @@ 
 };
 
 &usdhc0 {
+	assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>;
+	assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc0>;
 	cd-gpios = <&gpio_ptc 10 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
index 25e6f09..d37a192 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -223,8 +223,6 @@ 
 				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
 				 <&pcc2 IMX7ULP_CLK_USDHC0>;
 			clock-names = "ipg", "ahb", "per";
-			assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>;
-			assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
 			bus-width = <4>;
 			fsl,tuning-start-tap = <20>;
 			fsl,tuning-step = <2>;
@@ -239,8 +237,6 @@ 
 				 <&scg1 IMX7ULP_CLK_NIC1_DIV>,
 				 <&pcc2 IMX7ULP_CLK_USDHC1>;
 			clock-names = "ipg", "ahb", "per";
-			assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC1>;
-			assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
 			bus-width = <4>;
 			fsl,tuning-start-tap = <20>;
 			fsl,tuning-step = <2>;