@@ -457,6 +457,12 @@ config IMX_IRQSTEER
help
Support for the i.MX IRQSTEER interrupt multiplexer/remapper.
+config IMX_INTMUX
+ def_bool y if ARCH_MXC
+ select IRQ_DOMAIN
+ help
+ Support for the i.MX INTMUX interrupt multiplexer.
+
config LS1X_IRQ
bool "Loongson-1 Interrupt Controller"
depends on MACH_LOONGSON32
@@ -100,6 +100,7 @@ obj-$(CONFIG_CSKY_MPINTC) += irq-csky-mpintc.o
obj-$(CONFIG_CSKY_APB_INTC) += irq-csky-apb-intc.o
obj-$(CONFIG_SIFIVE_PLIC) += irq-sifive-plic.o
obj-$(CONFIG_IMX_IRQSTEER) += irq-imx-irqsteer.o
+obj-$(CONFIG_IMX_INTMUX) += irq-imx-intmux.o
obj-$(CONFIG_MADERA_IRQ) += irq-madera.o
obj-$(CONFIG_LS1X_IRQ) += irq-ls1x.o
obj-$(CONFIG_TI_SCI_INTR_IRQCHIP) += irq-ti-sci-intr.o
new file mode 100644
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright 2017 NXP
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/spinlock.h>
+
+#define CHANIER(n) (0x10 + (0x40 * n))
+#define CHANIPR(n) (0x20 + (0x40 * n))
+
+/* INTMUX Block Diagram
+ *
+ * ________________
+ * interrupt source # 0 +---->| |
+ * | | |
+ * interrupt source # 1 +++-->| |
+ * ... | | | channel # 0 |--------->interrupt out # 0
+ * ... | | | |
+ * ... | | | |
+ * interrupt source # X-1 +++-->|________________|
+ * | | |
+ * | | |
+ * | | | ________________
+ * +---->| |
+ * | | | | |
+ * | +-->| |
+ * | | | | channel # 1 |--------->interrupt out # 1
+ * | | +>| |
+ * | | | | |
+ * | | | |________________|
+ * | | |
+ * | | |
+ * | | | ...
+ * | | | ...
+ * | | |
+ * | | | ________________
+ * +---->| |
+ * | | | |
+ * +-->| |
+ * | | channel # N |--------->interrupt out # N
+ * +>| |
+ * | |
+ * |________________|
+ *
+ *
+ * N: Interrupt Channel Instance Number (N=7)
+ * X: Interrupt Source Number for each channel (X=32)
+ *
+ * The INTMUX interrupt multiplexer has 8 channels, each channel receives 32
+ * interrupt sources and generates 1 interrupt output.
+ *
+ * The aim of INTMUX design is to route same interrupt to different cores.
+ *
+ * In this driver, we only use channel 0 to steer 32 interrupt sources into 1
+ * interrupt out. We can extend the driver to support muti-channels in the
+ * future if has requirement.
+ *
+ */
+
+struct intmux_data {
+ void __iomem *regs;
+ struct clk *ipg_clk;
+ int chan_idx;
+ int irq;
+ struct irq_domain *domain;
+ raw_spinlock_t lock;
+};
+
+static void imx_intmux_irq_mask(struct irq_data *d)
+{
+ struct intmux_data *data = d->chip_data;
+ unsigned long flags;
+ void __iomem *reg;
+ u32 val;
+
+ raw_spin_lock_irqsave(&data->lock, flags);
+ reg = data->regs + CHANIER(data->chan_idx);
+ val = readl_relaxed(reg);
+ /* disable the interrupt source of this channel */
+ val &= ~(1 << d->hwirq);
+ writel_relaxed(val, reg);
+ raw_spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static void imx_intmux_irq_unmask(struct irq_data *d)
+{
+ struct intmux_data *data = d->chip_data;
+ unsigned long flags;
+ void __iomem *reg;
+ u32 val;
+
+ raw_spin_lock_irqsave(&data->lock, flags);
+ reg = data->regs + CHANIER(data->chan_idx);
+ val = readl_relaxed(reg);
+ /* enable the interrupt source of this channel */
+ val |= 1 << d->hwirq;
+ writel_relaxed(val, reg);
+ raw_spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static struct irq_chip imx_intmux_irq_chip = {
+ .name = "intmux",
+ .irq_mask = imx_intmux_irq_mask,
+ .irq_unmask = imx_intmux_irq_unmask,
+};
+
+static int imx_intmux_irq_map(struct irq_domain *h, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_status_flags(irq, IRQ_LEVEL);
+ irq_set_chip_data(irq, h->host_data);
+ irq_set_chip_and_handler(irq, &imx_intmux_irq_chip, handle_level_irq);
+
+ return 0;
+}
+
+static const struct irq_domain_ops imx_intmux_domain_ops = {
+ .map = imx_intmux_irq_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static void imx_intmux_irq_handler(struct irq_desc *desc)
+{
+ struct intmux_data *data = irq_desc_get_handler_data(desc);
+ unsigned long irqstat;
+ int pos, virq;
+
+ chained_irq_enter(irq_desc_get_chip(desc), desc);
+
+ /* read the interrupt source pending status of this channel */
+ irqstat = readl_relaxed(data->regs + CHANIPR(data->chan_idx));
+
+ for_each_set_bit(pos, &irqstat, 32) {
+ virq = irq_find_mapping(data->domain, pos);
+ if (virq)
+ generic_handle_irq(virq);
+ }
+
+ chained_irq_exit(irq_desc_get_chip(desc), desc);
+}
+
+static int imx_intmux_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct intmux_data *data;
+ int ret;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(data->regs)) {
+ dev_err(&pdev->dev, "failed to initialize reg\n");
+ return PTR_ERR(data->regs);
+ }
+
+ data->ipg_clk = devm_clk_get(&pdev->dev, "ipg");
+ if (IS_ERR(data->ipg_clk)) {
+ ret = PTR_ERR(data->ipg_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev, "failed to get ipg clk: %d\n", ret);
+ return ret;
+ }
+
+ raw_spin_lock_init(&data->lock);
+
+ ret = clk_prepare_enable(data->ipg_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable ipg clk: %d\n", ret);
+ return ret;
+ }
+
+ data->domain = irq_domain_add_linear(np, 32, &imx_intmux_domain_ops,
+ data);
+ if (!data->domain) {
+ dev_err(&pdev->dev, "failed to create IRQ domain\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ /* use channel 0 for interrupt output */
+ data->chan_idx = 0;
+
+ data->irq = irq_of_parse_and_map(np, data->chan_idx);
+ if (!data->irq) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ irq_set_chained_handler_and_data(data->irq, imx_intmux_irq_handler,
+ data);
+
+ /* disable all interrupt sources of this channel */
+ writel_relaxed(0, data->regs + CHANIER(data->chan_idx));
+
+ platform_set_drvdata(pdev, data);
+
+ return 0;
+out:
+ clk_disable_unprepare(data->ipg_clk);
+ return ret;
+}
+
+static int imx_intmux_remove(struct platform_device *pdev)
+{
+ struct intmux_data *data = platform_get_drvdata(pdev);
+
+ /* clear all interrupt sources pending status of this channel */
+ writel_relaxed(0, data->regs + CHANIPR(data->chan_idx));
+
+ irq_set_chained_handler_and_data(data->irq, NULL, NULL);
+
+ irq_domain_remove(data->domain);
+
+ clk_disable_unprepare(data->ipg_clk);
+
+ return 0;
+}
+
+static const struct of_device_id imx_intmux_id[] = {
+ { .compatible = "fsl,imx-intmux", },
+ { /* sentinel */ },
+};
+
+static struct platform_driver imx_intmux_driver = {
+ .driver = {
+ .name = "imx-intmux",
+ .of_match_table = imx_intmux_id,
+ },
+ .probe = imx_intmux_probe,
+ .remove = imx_intmux_remove,
+};
+builtin_platform_driver(imx_intmux_driver);
The Interrupt Multiplexer (INTMUX) expands the number of peripherals that can interrupt the core: * The INTMUX has 8 channels that are assigned to 8 NVIC interrupt slots. * Each INTMUX channel can receive up to 32 interrupt sources and has 1 interrupt output. * The INTMUX routes the interrupt sources to the interrupt outputs. In the driver, we only use channel 0 to steer 32 interrupt sources into 1 interrupt out. Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> --- drivers/irqchip/Kconfig | 6 + drivers/irqchip/Makefile | 1 + drivers/irqchip/irq-imx-intmux.c | 240 +++++++++++++++++++++++++++++++ 3 files changed, 247 insertions(+) create mode 100644 drivers/irqchip/irq-imx-intmux.c